Generated by kicad-footprint-generator · KiCad file format 20260206
25AA160AT-I
Microchip Tech · EEPROM · MSOP-8
25AA160AT-I from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | Chip Select input; a low level selects the device, a high level deselects it and forces Standby mode, and a low level is required after power-up before any sequence. |
| 2 | SO | tri_state | Serial Data Output; data is shifted out after the falling edge of the serial clock and the pin goes high-impedance when the device is deselected or HOLD is low. |
| 3 | WP | input | Write-Protect pin; with WPEN set, WP low disables writes to the nonvolatile STATUS register bits, and WP high allows all functions to operate normally. |
| 4 | VSS | power_in | Ground. |
| 5 | SI | input | Serial Data Input that receives instructions, addresses and data, latched on the rising edge of the serial clock. |
| 6 | SCK | input | Serial Clock input that synchronizes communication, latching SI on the rising edge and updating SO after the falling edge, with max clock 10 MHz. |
| 7 | HOLD | input | Hold input that pauses serial communication when pulled low while SCK is low, and must be held high when the function is not used. |
| 8 | VCC | power_in | Supply voltage, 1.8V to 5.5V for the 25AA160A (absolute maximum 7.0V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 7 | V | 2 | |||
| Input/output voltage w.r.t. VSS | -0.6 | V | All inputs and outputs; upper limit printed as VCC +1.0V | 2 | |||
| Storage temperature | -65 | 150 | °C | 2 | |||
| Ambient temperature under bias | -40 | 125 | °C | 2 | |||
| ESD protection on all pins | 4 | kV | 2 | ||||
| Supply voltage range (Industrial) | VCC | 1.8 | 5.5 | V | Industrial (I) | 2 | |
| Ambient temperature (Industrial) | TAMB | -40 | 85 | °C | Industrial (I) | 2 | |
| High-level input voltage | VIH1 | 2 | V | VCC ≥ 2.7V (Note); max printed as VCC +1 | 2 | ||
| Low-level input voltage | VIL1 | -0.3 | 0.8 | V | VCC ≥ 2.7V (Note) | 2 | |
| Low-level input voltage | VIL2 | -0.3 | V | VCC < 2.7V (Note); max printed as 0.2 VCC | 2 | ||
| Low-level output voltage | VOL | 0.4 | V | IOL = 2.1 mA | 2 | ||
| Low-level output voltage | VOL | 0.2 | V | IOL = 1.0 mA, VCC < 2.5V | 2 | ||
| Input leakage current | ILI | -1 | 1 | μA | CS = VCC, VIN = VSS TO VCC | 2 | |
| Output leakage current | ILO | -1 | 1 | μA | CS = VCC, VOUT = VSS TO VCC | 2 | |
| Internal capacitance (all inputs and outputs) | CINT | 7 | pF | TAMB = 25°C, CLK = 1.0 MHz, VCC = 5.0V (Note) | 2 | ||
| Read operating current | ICC Read | 6 | mA | VCC = 5.5V; FCLK = 10.0 MHz; SO = Open | 2 | ||
| Read operating current | ICC Read | 2.5 | mA | VCC = 2.5V; FCLK = 5.0 MHz; SO = Open | 2 | ||
| Write operating current | ICC Write | 3 | mA | VCC = 5.5V | 2 | ||
| Standby current | ICCS | 1 | μA | CS = VCC = 2.5V, Inputs tied to VCC or VSS, TAMB = -40°C TO +85°C | 2 | ||
| Clock frequency | FCLK | 10 | MHz | 4.5V ≤ VCC ≤ 5.5V | 3 | ||
| Clock frequency | FCLK | 3 | MHz | 1.8V ≤ VCC < 2.5V | 3 | ||
| CS setup time | TCSS | 50 | ns | 4.5V ≤ VCC ≤ 5.5V | 3 | ||
| CS setup time | TCSS | 150 | ns | 1.8V ≤ VCC < 2.5V | 3 | ||
| CS hold time | TCSH | 100 | ns | 4.5V ≤ VCC ≤ 5.5V | 3 | ||
| CS hold time | TCSH | 250 | ns | 1.8V ≤ VCC < 2.5V | 3 | ||
| CS disable time | TCSD | 50 | ns | 3 | |||
| Data setup time | Tsu | 10 | ns | 4.5V ≤ VCC ≤ 5.5V | 3 | ||
| Data setup time | Tsu | 30 | ns | 1.8V ≤ VCC < 2.5V | 3 | ||
| Data hold time | THD | 20 | ns | 4.5V ≤ VCC ≤ 5.5V | 3 | ||
| Data hold time | THD | 50 | ns | 1.8V ≤ VCC < 2.5V | 3 | ||
| CLK rise time | TR | 500 | ns | (Note 1) | 3 | ||
| CLK fall time | TF | 500 | ns | (Note 1) | 3 | ||
| Clock high time | THI | 50 | ns | 4.5V ≤ VCC ≤ 5.5V | 3 | ||
| Clock high time | THI | 150 | ns | 1.8V ≤ VCC < 2.5V | 3 | ||
| Clock low time | TLO | 50 | ns | 4.5V ≤ VCC ≤ 5.5V | 3 | ||
| Clock low time | TLO | 150 | ns | 1.8V ≤ VCC < 2.5V | 3 | ||
| Clock delay time | TCLD | 50 | ns | 3 | |||
| Clock enable time | TCLE | 50 | ns | 3 | |||
| Output valid from clock low | TV | 50 | ns | 4.5V ≤ VCC ≤ 5.5V | 3 | ||
| Output valid from clock low | TV | 160 | ns | 1.8V ≤ VCC < 2.5V | 3 | ||
| Output hold time | THO | 0 | ns | (Note 1) | 3 | ||
| Output disable time | TDIS | 40 | ns | 4.5V ≤ VCC ≤ 5.5V (Note 1) | 3 | ||
| Output disable time | TDIS | 160 | ns | 1.8V ≤ VCC ≤ 2.5V (Note 1) | 3 | ||
| HOLD setup time | THS | 20 | ns | 4.5V ≤ VCC ≤ 5.5V | 3 | ||
| HOLD setup time | THS | 80 | ns | 1.8V ≤ VCC < 2.5V | 3 | ||
| HOLD hold time | THH | 20 | ns | 4.5V ≤ VCC ≤ 5.5V | 4 | ||
| HOLD hold time | THH | 80 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| HOLD low to output High-Z | THZ | 30 | ns | 4.5V ≤ VCC ≤ 5.5V (Note 1) | 4 | ||
| HOLD low to output High-Z | THZ | 160 | ns | 1.8V ≤ VCC < 2.5V (Note 1) | 4 | ||
| HOLD high to output valid | THV | 30 | ns | 4.5V ≤ VCC ≤ 5.5V | 4 | ||
| HOLD high to output valid | THV | 160 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| Internal write cycle time | TWC | 5 | ms | (NOTE 3) | 4 |
CAD (KiCad official)
- Symbol:
25AA160AT-I - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
25aa160at-i-etched.step/25aa160at-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);25aa160at-i.step/25aa160at-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (26 pp, sha256
8a706dde7121e73c, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).