main
History Download
Ray Publish 0.1.2 08cfcd3

24LC04BHT-I

Microchip Tech · EEPROM · SOT-23-5

24LC04BHT-I from Microchip Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 SCL input Serial clock input used to synchronize data transfer to and from the device.
2 VSS power_in Ground reference for the device.
3 SDA bidirectional Open-drain serial address/data I/O that requires a pull-up resistor to VCC (typically 10 kΩ at 100 kHz, 2 kΩ at 400 kHz and 1 MHz), and may change only while SCL is low except for Start and Stop conditions.
4 VCC power_in Power supply; the 24LC04BH operates from 2.5V to 5.5V.
5 WP input Write-protect input that must be tied to VSS (write enabled for the full array 000h-1FFh) or to VCC (write inhibited for the upper half, 100h-1FFh; reads unaffected).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOT-23-5
Category Memory
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
All inputs and outputs w.r.t. VSS -0.3 V Printed upper limit is VCC + 1.0V 3
Storage temperature -65 150 °C 3
Ambient temperature with power applied -40 125 °C 3
ESD protection on all pins 4 kV 3
Supply voltage (24LC04BH) VCC 2.5 5.5 V Package Types table, 24LC04BH 1
Ambient temperature, Industrial (I) TA -40 85 °C Industrial (I) range 3
High-level input voltage VIH 0.7 VCC 3
Low-level input voltage VIL 0.3 VCC 3
Hysteresis of Schmitt trigger inputs VHYS 0.05 VCC Note 3
Low-level output voltage VOL 0.4 V IOL = 3.0 mA, VCC = 2.5V 3
Input leakage current ILI -1 1 µA VIN = VSS or VCC 3
Output leakage current ILO -1 1 µA VOUT = VSS or VCC 3
Pin capacitance (all inputs/outputs) CIN, COUT 10 pF VCC = 5.0V (Note); TA = 25°C, FCLK = 1 MHz 3
Operating current, write ICCWRITE 3 mA VCC = 5.5V, SCL = 400 kHz 3
Operating current, read ICCREAD 1 mA VCC = 5.5V, SCL = 400 kHz 3
Standby current (I-Temp) ICCS 1 µA SDA = SCL = VCC, WP = VSS, I-Temp. 3
Clock frequency FCLK 400 kHz 2.5V ≤ VCC ≤ 5.5V 4
Clock high time THIGH 600 ns 2.5V ≤ VCC ≤ 5.5V 4
Clock low time TLOW 1300 ns 2.5V ≤ VCC ≤ 5.5V 4
SDA and SCL rise time TR 300 ns 2.5V ≤ VCC ≤ 5.5V (Note 1) 4
SDA and SCL fall time TF 300 ns Note 1 4
Start condition hold time THD:STA 600 ns 2.5V ≤ VCC ≤ 5.5V 4
Start condition setup time TSU:STA 600 ns 2.5V ≤ VCC ≤ 5.5V 4
Data input hold time THD:DAT 0 ns Note 2 4
Data input setup time TSU:DAT 100 ns 2.5V ≤ VCC ≤ 5.5V 4
Stop condition setup time TSU:STO 600 ns 2.5V ≤ VCC ≤ 5.5V 4
WP setup time TSU:WP 600 ns 2.5V ≤ VCC ≤ 5.5V 4
WP hold time THD:WP 1300 ns 2.5V ≤ VCC ≤ 5.5V 4
Output valid from clock TAA 900 ns 2.5V ≤ VCC ≤ 5.5V (Note 2) 5
Bus free time TBUF 1300 ns 2.5V ≤ VCC ≤ 5.5V 5
Output fall time from VIH min to VIL max TOF 250 ns 2.5V ≤ VCC ≤ 5.5V (Notes 1, 2 and 3) 5
Input filter spike suppression (SDA and SCL) TSP 50 ns Note 1 5
Write cycle time (byte or page) TWC 5 ms 5
Endurance 1e+06 cycles 25°C, 5.5V, Page Mode (Note 4) 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 21

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: 24LC04BHT-I
  • Footprint: Package_TO_SOT_SMD:SOT-23-5
  • 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: 24lc04bht-i-etched.step / 24lc04bht-i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); 24lc04bht-i.step / 24lc04bht-i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (40 pp, sha256 40eeba59625ba6ea, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF