main
Download ZIP Propose a change
Generated by adom_assets · KiCad file format 20240108
Name Last commit message Last updated
docs Publish 0.3.0 · Ray
viewers 24lc01bt-i-ms: viewers · Ray
24lc01bt-i-etched.fit.json 24lc01bt-i: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
24lc01bt-i-ms-etched.glb 24lc01bt-i-ms: rebuilt as a full factory component page (was a placeholder) · Ray
24lc01bt-i-ms-etched.step 24lc01bt-i-ms: rebuilt as a full factory component page (was a placeholder) · Ray
24lc01bt-i-ms-hero.glb Publish 0.3.0 · Ray
24lc01bt-i-ms-hero.overlay.json Publish 0.3.0 · Ray
24lc01bt-i-ms.glb Publish 0.3.0 · Ray
24lc01bt-i-ms.kicad_mod Publish 0.3.0 · Ray
24lc01bt-i-ms.kicad_sym Publish 0.3.0 · Ray
24lc01bt-i-ms.lbr Publish 0.3.0 · Ray
24lc01bt-i-ms.step Publish 0.3.0 · Ray
package.json Publish 0.3.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.3.0 · Ray

24LC01BT-I

Microchip makes this part in eight packages; this page is the 8-lead MSOP (ordering code 24LC01BT-I/MS). The SOT-23-5 version (24LC01BT-I/OT) has a different, 5-pin pinout.

Microchip · EEPROM · MSOP-8

24LC01BT-I from Microchip, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 A0 no_connect Not Connected. Not used by the 24XX01; may be left floating or tied to VSS or VCC (sec. 2.1).
2 A1 no_connect Not Connected. Not used by the 24XX01; may be left floating or tied to VSS or VCC (sec. 2.1).
3 A2 no_connect Not Connected. Not used by the 24XX01; may be left floating or tied to VSS or VCC (sec. 2.1).
4 VSS power_in Ground.
5 SDA bidirectional Serial Address/Data I/O. Bidirectional, open drain: needs a pull-up to VCC.
6 SCL input Serial Clock input.
7 WP input Write-Protect Input. Tie to VSS (writes enabled) or VCC (writes inhibited); must not float.
8 VCC power_in Power Supply, 2.5 V to 5.5 V (24LC01B).

Key specifications

Parameter Value
Manufacturer Microchip
Package MSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Voltage on all inputs and outputs -0.3 V w.r.t. VSS; upper limit printed as VCC +1.0V 3
Storage temperature -65 150 °C 3
Ambient temperature with power applied -40 125 °C 3
Supply voltage (24LC01B, Industrial) VCC 2.5 5.5 V Industrial (I) grade, 24LC01B 3
Ambient temperature (Industrial) TA -40 85 °C Industrial (I) grade 3
High-level input voltage VIH 0.7 VCC Printed as 0.7 VCC 3
Low-level input voltage VIL 0.3 VCC Printed as 0.3 VCC 3
Hysteresis of Schmitt trigger inputs VHYS 0.05 VCC Printed as 0.05 VCC; periodically sampled, not 100% tested 3
Low-level output voltage VOL 0.4 V IOL = 3.0 mA, VCC = 2.5V 3
Input leakage current ILI -1 1 µA VIN = VSS or VCC 3
Output leakage current ILO -1 1 µA VOUT = VSS or VCC 3
Pin capacitance (all inputs/outputs) CIN, COUT 10 pF VCC = 5.0V; TA = 25°C, FCLK = 1 MHz; periodically sampled 3
Operating current, write ICCWRITE 3 mA VCC = 5.5V, SCL = 400 kHz 3
Operating current, read ICCREAD 1 mA VCC = 5.5V, SCL = 400 kHz 3
Standby current (I-temp) ICCS 1 µA SDA = SCL = VCC, WP = VSS, I-Temp. 3
Clock frequency FCLK 400 kHz 2.5V ≤ VCC ≤ 5.5V 4
Clock high time THIGH 600 ns 2.5V ≤ VCC ≤ 5.5V 4
Clock low time TLOW 1300 ns 2.5V ≤ VCC ≤ 5.5V 4
SDA and SCL rise time TR 300 ns 2.5V ≤ VCC ≤ 5.5V (Note 1) 4
SDA and SCL fall time TF 300 ns Note 1 4
Start condition hold time THD:STA 600 ns 2.5V ≤ VCC ≤ 5.5V 4
Start condition setup time TSU:STA 600 ns 2.5V ≤ VCC ≤ 5.5V 4
Data input hold time THD:DAT 0 ns Note 2 4
Data input setup time TSU:DAT 100 ns 2.5V ≤ VCC ≤ 5.5V 4
Stop condition setup time TSU:STO 600 ns 2.5V ≤ VCC ≤ 5.5V 4
Output valid from clock TAA 900 ns 2.5V ≤ VCC ≤ 5.5V (Note 2) 4
Bus free time TBUF 1300 ns 2.5V ≤ VCC ≤ 5.5V 5
Output fall time from VIH minimum to VIL maximum TOF 250 ns 2.5V ≤ VCC ≤ 5.5V (Notes 1 and 3) 5
Input filter spike suppression (SDA and SCL) TSP 50 ns Note 1 5
Write cycle time (byte or page) TWC 5 ms 5
Endurance 1e+06 cycles 25°C, 5.5V, Page Mode (Note 4) 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 27

CAD (Adom-generated)

  • Symbol: 24LC01BT-I
  • Footprint: Adom_Gen:Microchip_Tech_24_360677
  • 3D model: generated to fit the land (STEP)
  • 3D model files: 24lc01bt-i-ms-etched.step / 24lc01bt-i-ms-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); 24lc01bt-i-ms.step / 24lc01bt-i-ms.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip datasheet (45 pp, sha256 ae7b4fad39d5eebc, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land. Land: Microchip Technology Drawing C04-2111A, 8-Lead MSOP RECOMMENDED LAND PATTERN (DS20001711L p.21): E 0.65 BSC, C 4.40, X1 0.45 max, Y1 1.45 max, G1 2.95 min, GX 0.20 min, Z 5.85 max.

Datasheet PDF