Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

24CW1280T-I

Microchip Tech · Pre-ordered Chips · SOT-23-5

24CW1280T-I from Microchip Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 SCL input Serial clock input used to synchronize data transfer to and from the device.
2 VSS power_in Ground reference for the device.
3 SDA bidirectional Open-drain serial data pin that requires a pull-up resistor to VCC (typically 10 kΩ for 100 kHz and 2 kΩ for 400 kHz and 1 MHz); SDA may change only while SCL is low except for Start and Stop conditions.
4 VCC power_in Device power supply, operating from 1.6 V to 5.5 V.
5 NC unconnected No connect pin, listed as NC in the pin function table for the 5-Lead SOT-23 package.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOT-23-5
Category Interface ICs
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Low-Level Output Voltage VOL 0.4 V IOL = 2.1 mA, VCC = 3.0V 4
Low-Level Output Voltage VOL 0.2 V IOL = 0.15 mA, VCC = 1.8V 4
Input Leakage Current ILI -1 1 µA VIN = VSS or VCC 4
Output Leakage Current ILO -1 1 µA VOUT =VSS or VCC 4
Internal Capacitance (all inputs and outputs) CINT 7 pF TAMB = +25°C, FCLK = 1 MHz, VCC = 5.5V (Note 1) 4
Operating Current ICCREAD 0.3 mA VCC = 1.8V, FCLK = 400 kHz 4
Operating Current ICCREAD 1 mA VCC = 5.5V, FCLK = 1 MHz 4
Standby Current ICCS 0.5 µA SCL = SDA = VCC = 1.8V 4
Standby Current ICCS 1 µA SCL = SDA = VCC = 5.5V 4
Clock Frequency FCLK 1000 kHz 1.6V ≤ VCC ≤ 5.5V 5
Clock High Time THIGH 260 ns 1.6V ≤ VCC ≤ 5.5V 5
Clock Low Time TLOW 500 ns 1.6V ≤ VCC ≤ 5.5V 5
SDA and SCL Rise Time TR 1000 ns 1.6V ≤ VCC ≤ 5.5V (Note 1) 5
SDA and SCL Fall Time TF 300 ns 1.6V ≤ VCC ≤ 5.5V (Note 1) 5
Start Condition Hold Time THD:STA 260 ns 1.6V ≤ VCC ≤ 5.5V 5
Start Condition Setup Time TSU:STA 260 ns 1.6V ≤ VCC ≤ 5.5V 5
Data Input Hold Time THD:DAT 0 ns (Note 2) 5
Data Input Setup Time TSU:DAT 50 ns 1.6V ≤ VCC ≤ 5.5V 5
Stop Condition Setup Time TSU:STO 260 ns 1.6V ≤ VCC ≤ 5.5V 5
Output Valid from Clock TAA 450 ns 1.6V ≤ VCC ≤ 5.5V 5
Bus Free Time: Bus Time must be Free before a New Transmission can Start TBUF 500 ns 1.6V ≤ VCC ≤ 5.5V 5
Input Filter Spike Suppression (SDA and SCL pins) TSP 50 ns (Note 3) 5
Write Cycle Time (byte or page) TWC 5 ms 5
Write Endurance 1e+06 Write Cycles TA = 25°C, 1.6V VCC 5.5V 5
Data Retention 200 Years TA = 55°C 5
Time Required after VCC is Stable before the Device can Accept Commands TPUP 100 µs 6
Power-on Reset Threshold Voltage VPOR 1.5 V 6
Minimum Time at VCC = 0V between Power Cycles TPOFF 1 ms 6
Supply voltage VCC 1.6 5.5 V Industrial (I) grade 4
Ambient temperature TA -40 85 °C Industrial (I) grade 4
Supply voltage VCC 6.5 V 4
All inputs and outputs w.r.t. VSS -0.6 6.5 V 4
Storage temperature -65 150 °C 4
Ambient temperature under bias -40 85 °C 4
ESD protection on all pins 4 kV Printed as >4 kV 4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin Package: SN = 8-Lead Plastic Small Outline, Narrow, 3.90 mm Body 48

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: 24CW1280T-I
  • Footprint: Package_TO_SOT_SMD:SOT-23-5
  • 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: 24cw1280t-i-ot-etched.step / 24cw1280t-i-ot-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); 24cw1280t-i-ot.step / 24cw1280t-i-ot.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (50 pp, sha256 213f52757c654a29, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF