Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

24CS256T-E/OT

Microchip Tech · EEPROM · SOT-23-5

24CS256T-E from Microchip Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SCL input Serial clock input used to synchronize data transfer from and to the device.
2 VSS power_in Ground reference for the device.
3 SDA bidirectional Open-drain serial data pin requiring a pull-up resistor to VCC (typically 10 kΩ for 100 kHz, 2 kΩ for 400 kHz and 1 MHz, and 330 Ω for 3.4 MHz).
4 VCC power_in Device power supply pin.
5 WP input Must be tied to VSS to enable writes to the memory array and Security register, or to VCC to inhibit those writes while reads are unaffected.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOT-23-5
Category Memory
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Low-Level Input Voltage VIL -0.6 V 4
Low-Level Output Voltage VOL 0.4 V IOL = 2.1 mA, VCC ≥ 2.5V 4
Low-Level Output Voltage VOL 0.2 V IOL = 0.15 mA, VCC < 2.5V 4
Input Leakage Current ILI -1 1 µA VIN = VSS or VCC 4
Output Leakage Current ILO -1 1 µA VOUT =VSS or VCC 4
Internal Capacitance (all inputs and outputs) CINT 7 pF TAMB = +25°C, FCLK = 1 MHz, VCC = 5.5V (Note 1) 4
Operating Current (read) ICCREAD 1 mA VCC = 5.5V, FCLK = 1 MHz 4
Operating Current (write) ICCWRITE 3 mA VCC = 5.5V 4
Operating Current (write) ICCWRITE 1 mA VCC = 1.7V 4
Standby Current ICCS 3 µA SCL = SDA = VCC = 5.5V, WP = VSS, E-Temp. 4
Clock Frequency FCLK 1000 kHz 1.7V ≤ VCC ≤ 5.5V 5
Clock High Time THIGH 400 ns 1.7V ≤ VCC ≤ 5.5V 5
Clock Low Time TLOW 400 ns 1.7V ≤ VCC ≤ 5.5V 5
SDA and SCL Rise Time TR 1000 ns 1.7V ≤ VCC ≤ 5.5V (Note 1) 5
SDA and SCL Fall Time TF 300 ns 1.7V ≤ VCC ≤ 5.5V (Note 1) 5
Start Condition Hold Time THD:STA 250 ns 1.7V ≤ VCC ≤ 5.5V 5
Start Condition Setup Time TSU:STA 250 ns 1.7V ≤ VCC ≤ 5.5V 5
Data Input Hold Time THD:DAT 0 ns Note 2 5
Data Input Setup Time TSU:DAT 50 ns 1.7V ≤ VCC ≤ 5.5V 5
Stop Condition Setup Time TSU:STO 250 ns 1.7V ≤ VCC ≤ 5.5V 5
WP Setup Time TSU:WP 600 ns 5
WP Hold Time THD:WP 1300 ns 5
Output Valid from Clock TAA 400 ns 1.7V ≤ VCC ≤ 5.5V 5
Bus Free Time TBUF 500 ns 1.7V ≤ VCC ≤ 5.5V 5
Input Filter Spike Suppression (SDA and SCL pins) TSP 100 ns 1.7V ≤ VCC ≤ 5.5V (Note 3) 5
Write Cycle Time (byte or page) TWC 5 ms 5
Write Endurance 1e+06 Write Cycles TA = 25°C, 1.7V ≤ Vcc ≤ 5.5V 6
Data Retention 200 Years TA = 55°C 6
Time required after VCC is stable before the device can accept commands TPUP 100 µs 7
Power-on Reset threshold voltage VPOR 1.5 V 7
Minimum time at VCC = 0V between power cycles TPOFF 1 ms 7
VCC power-up slew rate 0.1 V/µs Power-up, VCC rising monotonically from VSS to minimum VCC 7
VCC (absolute maximum) VCC 6.5 V 4
All inputs and outputs w.r.t. VSS -0.6 6.5 V 4
Storage temperature -65 150 °C 4
Ambient temperature under bias -40 125 °C 4
Supply voltage VCC 1.7 5.5 V Extended (E) electrical characteristics 4
Ambient temperature (Extended grade) TA -40 125 °C Extended (E) electrical characteristics 4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 47

CAD (KiCad official)

  • Symbol: 24CS256T-E
  • Footprint: Package_TO_SOT_SMD:SOT-23-5
  • 3D model: SOT-23-5 (KiCad packages3D, STEP)
  • 3D model files: 24cs256t-e-etched.step / 24cs256t-e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); 24cs256t-e.step / 24cs256t-e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (66 pp, sha256 af110a1feddf4dc1, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

Other parts in this family

This page is 24CS256T-E/OT. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:

  • 24CS256T-E/ST