24C02N

{
 "schema": "adom.pads/1",
 "slug": "24c02n",
 "footprint": "DIP-8_W7.62mm",
 "generated_from": {
  "footprint": "DIP-8_W7.62mm@sha256:222fb44370968119",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   0.0,
   0.0
  ],
  "corner": "bottom-right",
  "source": "fab-chamfer",
  "derived_from": "DIP-8_W7.62mm@sha256:222fb44370968119"
 },
 "pad_count": 8,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6",
  "7",
  "8"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "thru_hole",
   "shape": "roundrect",
   "at": [
    0.0,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "1",
   "name": "A0",
   "type": "input",
   "description": "Device/chip-select address input bit 0. Hardwired to VIH or VIL to set the low bit of the 3-bit slave address (device address bits 5-7 of the I2C address byte). Recommended pull-up/pull-down resistor 10 kohm or less; internally interpreted as VIL if left floating but external tie is strongly recommended.",
   "is_pin1": true,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    0.0,
    2.54
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "2",
   "name": "A1",
   "type": "input",
   "description": "Device/chip-select address input bit 1. Hardwired to VIH or VIL to set the middle bit of the 3-bit slave address. Recommended pull-up/pull-down resistor 10 kohm or less.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    0.0,
    5.08
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "3",
   "name": "A2",
   "type": "input",
   "description": "Device/chip-select address input bit 2. Hardwired to VIH or VIL to set the high bit of the 3-bit slave address. Together A2/A1/A0 allow up to eight 24C02 devices to share one I2C bus.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    0.0,
    7.62
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "4",
   "name": "GND",
   "type": "power_in",
   "description": "Ground reference (0 V) for the device.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    7.62,
    7.62
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "5",
   "name": "SDA",
   "type": "bidirectional",
   "description": "Serial data line for the two-wire (I2C-compatible) bus. Bidirectional, open-drain output; requires an external pull-up resistor to VCC. Data may only change when SCL is low; SDA transitions while SCL is high are interpreted as START or STOP conditions.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    7.62,
    5.08
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "6",
   "name": "SCL",
   "type": "input",
   "description": "Serial clock input for the two-wire bus. Rising edge latches data into the EEPROM; falling edge clocks data out. Supports 1 MHz at 2.5-5V and 400 kHz at 1.8V. Requires an external pull-up on the bus.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "7",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    7.62,
    2.54
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "7",
   "name": "WP",
   "type": "input",
   "description": "Write-protect input. Tied to VIL (or left floating - internally read as VIL, but tie is recommended) allows all programming operations; tied to VIH or VCC disables all write operations while still allowing reads. Recommended pull-up/pull-down resistor 10 kohm or less.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "8",
   "kind": "thru_hole",
   "shape": "circle",
   "at": [
    7.62,
    0.0
   ],
   "rot": 0.0,
   "size": [
    1.6,
    1.6
   ],
   "layers": [],
   "thermal": false,
   "pin": "8",
   "name": "VCC",
   "type": "power_in",
   "description": "Positive supply. Operating range 1.8 V to 5.5 V (industrial temperature -40 to +85 C). Absolute maximum 8 V; any input must stay within -0.3 V to VCC + 0.3 V.",
   "is_pin1": false,
   "source": {
    "geometry": "DIP-8_W7.62mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}