component
24AA16T-I/OT
Public Made by Adomby adom
Microchip Tech EEPROM, SOT-23-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.2
4175d82
24AA16T-I
Microchip Tech · EEPROM · SOT-23-5
24AA16T-I from Microchip Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | The serial clock input synchronizes data transfer to and from the device, with Schmitt-trigger input and noise filtering; the 24AA16 is limited to 100 kHz when VCC is below 2.5V. |
| 2 | VSS | power_in | Ground reference for the device; the datasheet gives no further electrical limit for this pin. |
| 3 | SDA | bidirectional | Open-drain serial address/data I/O that requires a pull-up resistor to VCC (typically 10 kΩ at 100 kHz, 2 kΩ at 400 kHz and 1 MHz), and may change only while SCL is low except for Start and Stop conditions. |
| 4 | VCC | power_in | Power supply; the 24AA16 operates from 1.7V to 5.5V. |
| 5 | WP | input | Write-protect input that must be tied to VSS (writes enabled) or VCC (entire array write-protected, reads unaffected). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOT-23-5 |
| Category | Memory |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| High-Level Input Voltage | VIH | 0.7 | VCC | 3 | |||
| Low-Level Input Voltage | VIL | 0.3 | VCC | 3 | |||
| Hysteresis of Schmitt Trigger Inputs | VHYS | 0.05 | VCC | Note | 3 | ||
| Low-Level Output Voltage | VOL | 0.4 | V | IOL = 3.0 mA, VCC = 2.5V | 3 | ||
| Input Leakage Current | ILI | -1 | 1 | μA | VIN = VSS or VCC | 3 | |
| Output Leakage Current | ILO | -1 | 1 | μA | VOUT = VSS or VCC | 3 | |
| Pin Capacitance (all inputs/outputs) | CIN, COUT | 10 | pF | VCC = 5.0V (Note); TA = 25°C, FCLK = 1 MHz | 3 | ||
| Operating Current (write) | ICCWRITE | 3 | mA | VCC = 5.5V, SCL = 400 kHz | 3 | ||
| Operating Current (read) | ICCREAD | 1 | mA | VCC = 5.5V, SCL = 400 kHz | 3 | ||
| Standby Current (I-Temp.) | ICCS | 1 | μA | SDA = SCL = VCC; WP = VSS; I-Temp. | 3 | ||
| Clock Frequency | FCLK | 400 | kHz | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Clock Frequency | FCLK | 100 | kHz | 1.7V ≤ VCC < 2.5V (24AA16) | 4 | ||
| Clock High Time | THIGH | 600 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Clock High Time | THIGH | 4000 | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 | ||
| Clock Low Time | TLOW | 1300 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Clock Low Time | TLOW | 4700 | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 | ||
| SDA and SCL Rise Time | TR | 300 | ns | 2.5V ≤ VCC ≤ 5.5V (Note 1) | 4 | ||
| SDA and SCL Rise Time | TR | 1000 | ns | 1.7V ≤ VCC < 2.5V (24AA16) (Note 1) | 4 | ||
| SDA and SCL Fall Time | TF | 300 | ns | Note 1 | 4 | ||
| Start Condition Hold Time | THD:STA | 600 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Start Condition Hold Time | THD:STA | 4000 | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 | ||
| Start Condition Setup Time | TSU:STA | 600 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Start Condition Setup Time | TSU:STA | 4700 | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 | ||
| Data Input Hold Time | THD:DAT | 0 | ns | Note 2 | 4 | ||
| Data Input Setup Time | TSU:DAT | 100 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Data Input Setup Time | TSU:DAT | 250 | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 | ||
| Stop Condition Setup Time | TSU:STO | 600 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Stop Condition Setup Time | TSU:STO | 4000 | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 | ||
| Output Valid from Clock | TAA | 900 | ns | 2.5V ≤ VCC ≤ 5.5V (Note 2) | 4 | ||
| Output Valid from Clock | TAA | 3500 | ns | 1.7V ≤ VCC < 2.5V (24AA16) (Note 2) | 4 | ||
| Bus Free Time | TBUF | 1300 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Bus Free Time | TBUF | 4700 | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 | ||
| Output Fall Time from VIH Minimum to VIL Maximum | TOF | 250 | ns | 2.5V ≤ VCC ≤ 5.5V (Notes 1, 3 and 4) | 5 | ||
| Input Filter Spike Suppression (SDA and SCL pins) | TSP | 50 | ns | Note 1 | 5 | ||
| Write Cycle Time (byte or page) | TWC | 5 | ms | byte or page | 5 | ||
| Endurance | 1e+06 | cycles | 25°C, 5.5V, Page Mode (Note 4) | 5 | |||
| Supply voltage VCC (24AA16) | VCC | 1.7 | 5.5 | V | 24AA16 (1.7V-5.5V VCC range) | 1 | |
| Operating ambient temperature, Industrial (I) | TA | -40 | 85 | °C | Industrial (I) grade | 3 | |
| All inputs and outputs w.r.t. VSS | -0.3 | V | 3 | ||||
| Storage temperature | -65 | 150 | °C | 3 | |||
| Ambient temperature with power applied | TA | -40 | 125 | °C | 3 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 25 |
CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol:
24AA16T-I - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
24aa16t-i-ot-etched.step/24aa16t-i-ot-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);24aa16t-i-ot.step/24aa16t-i-ot.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (46 pp, sha256
dac4103ab691cf4a, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
# 24AA16T-I
**Microchip Tech** · EEPROM · SOT-23-5
24AA16T-I from Microchip Tech, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | The serial clock input synchronizes data transfer to and from the device, with Schmitt-trigger input and noise filtering; the 24AA16 is limited to 100 kHz when VCC is below 2.5V. |
| 2 | VSS | power_in | Ground reference for the device; the datasheet gives no further electrical limit for this pin. |
| 3 | SDA | bidirectional | Open-drain serial address/data I/O that requires a pull-up resistor to VCC (typically 10 kΩ at 100 kHz, 2 kΩ at 400 kHz and 1 MHz), and may change only while SCL is low except for Start and Stop conditions. |
| 4 | VCC | power_in | Power supply; the 24AA16 operates from 1.7V to 5.5V. |
| 5 | WP | input | Write-protect input that must be tied to VSS (writes enabled) or VCC (entire array write-protected, reads unaffected). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOT-23-5 |
| Category | Memory |
| Pins | 5 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| High-Level Input Voltage | VIH | 0.7 | | | VCC | | 3 |
| Low-Level Input Voltage | VIL | | | 0.3 | VCC | | 3 |
| Hysteresis of Schmitt Trigger Inputs | VHYS | 0.05 | | | VCC | Note | 3 |
| Low-Level Output Voltage | VOL | | | 0.4 | V | IOL = 3.0 mA, VCC = 2.5V | 3 |
| Input Leakage Current | ILI | -1 | | 1 | μA | VIN = VSS or VCC | 3 |
| Output Leakage Current | ILO | -1 | | 1 | μA | VOUT = VSS or VCC | 3 |
| Pin Capacitance (all inputs/outputs) | CIN, COUT | | | 10 | pF | VCC = 5.0V (Note); TA = 25°C, FCLK = 1 MHz | 3 |
| Operating Current (write) | ICCWRITE | | | 3 | mA | VCC = 5.5V, SCL = 400 kHz | 3 |
| Operating Current (read) | ICCREAD | | | 1 | mA | VCC = 5.5V, SCL = 400 kHz | 3 |
| Standby Current (I-Temp.) | ICCS | | | 1 | μA | SDA = SCL = VCC; WP = VSS; I-Temp. | 3 |
| Clock Frequency | FCLK | | | 400 | kHz | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Clock Frequency | FCLK | | | 100 | kHz | 1.7V ≤ VCC < 2.5V (24AA16) | 4 |
| Clock High Time | THIGH | 600 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Clock High Time | THIGH | 4000 | | | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 |
| Clock Low Time | TLOW | 1300 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Clock Low Time | TLOW | 4700 | | | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 |
| SDA and SCL Rise Time | TR | | | 300 | ns | 2.5V ≤ VCC ≤ 5.5V (Note 1) | 4 |
| SDA and SCL Rise Time | TR | | | 1000 | ns | 1.7V ≤ VCC < 2.5V (24AA16) (Note 1) | 4 |
| SDA and SCL Fall Time | TF | | | 300 | ns | Note 1 | 4 |
| Start Condition Hold Time | THD:STA | 600 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Start Condition Hold Time | THD:STA | 4000 | | | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 |
| Start Condition Setup Time | TSU:STA | 600 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Start Condition Setup Time | TSU:STA | 4700 | | | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 |
| Data Input Hold Time | THD:DAT | 0 | | | ns | Note 2 | 4 |
| Data Input Setup Time | TSU:DAT | 100 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Data Input Setup Time | TSU:DAT | 250 | | | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 |
| Stop Condition Setup Time | TSU:STO | 600 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Stop Condition Setup Time | TSU:STO | 4000 | | | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 |
| Output Valid from Clock | TAA | | | 900 | ns | 2.5V ≤ VCC ≤ 5.5V (Note 2) | 4 |
| Output Valid from Clock | TAA | | | 3500 | ns | 1.7V ≤ VCC < 2.5V (24AA16) (Note 2) | 4 |
| Bus Free Time | TBUF | 1300 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Bus Free Time | TBUF | 4700 | | | ns | 1.7V ≤ VCC < 2.5V (24AA16) | 4 |
| Output Fall Time from VIH Minimum to VIL Maximum | TOF | | | 250 | ns | 2.5V ≤ VCC ≤ 5.5V (Notes 1, 3 and 4) | 5 |
| Input Filter Spike Suppression (SDA and SCL pins) | TSP | | | 50 | ns | Note 1 | 5 |
| Write Cycle Time (byte or page) | TWC | | | 5 | ms | byte or page | 5 |
| Endurance | | 1e+06 | | | cycles | 25°C, 5.5V, Page Mode (Note 4) | 5 |
| Supply voltage VCC (24AA16) | VCC | 1.7 | | 5.5 | V | 24AA16 (1.7V-5.5V VCC range) | 1 |
| Operating ambient temperature, Industrial (I) | TA | -40 | | 85 | °C | Industrial (I) grade | 3 |
| All inputs and outputs w.r.t. VSS | | -0.3 | | | V | | 3 |
| Storage temperature | | -65 | | 150 | °C | | 3 |
| Ambient temperature with power applied | TA | -40 | | 125 | °C | | 3 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 25 |
## CAD (land: KiCad; 3D: generated from the datasheet)
- Symbol: `24AA16T-I`
- Footprint: `Package_TO_SOT_SMD:SOT-23-5`
- 3D model: SOT-23-5, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files: `24aa16t-i-ot-etched.step` / `24aa16t-i-ot-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `24aa16t-i-ot.step` / `24aa16t-i-ot.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/20001703M.pdf) (46 pp, sha256 `dac4103ab691cf4a`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).
[Datasheet PDF](docs/24aa16t-i-ot-datasheet.pdf)