component

2-1445098-3

Public Made by Adom

by adom

TE Connectivity Micro MATE-N-LOK header, right angle, 3 position, 3.00 mm pitch, plastic holddown. Footprint and 3D built from the TE drawing.

componentconnectors2-1445098-3board-derived

Verified 2-1445098-3

by Claude, at Caleb Taylor's request · last 27 Oct 2026 · 1 record · files match
SymbolFootprint3D modelPins

Verification log 3 records

27 Oct 2026Claude, at Caleb Taylor's requestValidated against TE customer drawing C-1445098 rev C; footprint and 3D rebuilt to the drawingfiles match
SymbolFootprint3D modelPinsfor all variants
  • ✓Datasheet: TE customer drawing C-1445098 rev C (12 Dec 2025, ECN-25-359104), 2 sheets, re-downloaded from te.com 2026-10-27, byte-identical to the page copy (sha256 86b030c7...).
  • ✓BOM: NTX_CCX-MIO_Carrier_v1.1 J13 is "TE: 2-1445098-3" (BOM, schematic and board value), the same MPN as the page: the page is the intended part.
  • ✓Pins 1-3: names are the contact numbers (the drawing has no signal names), all passive. Circuit 1 = right-hand cavity seen from the mating face (sheet 1 CIRCUIT NUMBER 1); 2 and 3 follow in order. Descriptions rewritten with the cavity keying from sheet 2.
  • ✓Footprint rebuilt from sheet 2 PCB LAYOUT FOR 3 POSITION: contacts at 3.00 pitch (6.00 span), drill 1.12 (middle of the 1.02 +0.20/-0 finished-hole band), pads 1.80; holddown hole 3.00 +-0.08 NPTH centred on contact 2, 4.32 from the row on the mating-face side; overlay of the drills on the layout coincides (provenance/evidence/overlay_sheet2_pcb_layout.png). Old footprint was a 2.54 mm vertical socket (pins 2 and 3 0.46 and 0.92 mm off, drill 1.00, no holddown hole).
  • ✓Pin 1 orientation: third-angle projection (title-block symbol); in the top view circuit 1 is on the right with the mating face toward the viewer, so with the mating face toward -y pad 1 is at x = -3.00. Silk triangle and F.Fab chevron mark pad 1; courtyard 0.5 mm round the body (latches +-6.57, face -8.92, contact bend +0.94).
  • ✓3D rebuilt (tier 3, cadquery, CC-BY-SA-4.0) from the drawing: 13.14 x 9.86 x 9.18 mm; DIM W 13.14 +-0.39, DIM Y 10.00, 3.86 + 0.51 housing, 1.30 latch, (8.92) face, (7.88) holddown tip, DIM X 3.30 +-0.15 barbs; overlays on the sheet 1 side view and sheet 2 3 POS view coincide. TE STEP rejected: te.com terms forbid redistribution. KiCad has no Micro MATE-N-LOK model.
  • •Undimensioned detail measured off the drawing at 47.24 px/mm; cavity depth (6.0) and mating-pin tip position are cosmetic assumptions (not shown on the drawing), recorded in provenance/3d-model.json.
  • ✓step_pose.py: plain and etched STEP PASS (Z-up, seated, THT tails and peg below, identity binding); body 3.99 mm off the pad-pattern centre by design (right-angle overhang), courtyard centred on the body, contacts in all 3 holes.
  • •Symbol Footprint property changed from Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical to 2-1445098-3:2-1445098-3 (the page footprint).
  • ✓Distributors: DigiKey A34859-ND (TE Connectivity AMP Connectors 2-1445098-3, CONN HEADER R/A 3POS 3MM) and Mouser 571-2-1445098-3 (TE Connectivity / AMP 2-1445098-3) confirmed by search 2026-10-27.
  • •Board affected: NTX_CCX-MIO_Carrier_v1.1 J13 uses Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical (2.54 pitch, drill 1.00, no holddown hole), so the part cannot be fitted there; the board is Caleb's to change.
  • ✓Symbol Datasheet / MPN / Manufacturer / DigiKey / Mouser / LCSC properties agree with page.json; footprint Datasheet property points at the manufacturer datasheet URL
  • ✓component-page-verify: all checks pass
EvidenceTE customer drawing C-1445098 rev Cte.com Terms of Use (why TE CAD is not redistributed)
Verified files✓ 2-1445098-3.kicad_sym✓ 2-1445098-3.kicad_mod✓ 2-1445098-3.step
9 Oct 2026Claude (AI build)Board uses a generic KiCad pin-header footprint and model, not a Micro MATE-N-LOK land pat...superseded
reviewfor all variants
  • •Board uses a generic KiCad pin-header footprint and model, not a Micro MATE-N-LOK land pattern (3.0 mm pitch, right angle, hold-downs). Footprint and 3D need checking against the TE drawing before use.
9 Oct 2026Claude (AI build)Automated build checks (awaiting human validation)superseded
SymbolFootprint3D modelPinsfor all variants
  • ✓Footprint extracted pad-for-pad from the source board and normalized to the footprint frame (back-side parts un-mirrored)
  • ✓3D model seated z=0 at footprint origin (placement inverse; method centroid-matched to KiCad library models on 59 cases)
  • ✓adom-lbr generate + lint passed
  • ✓3 of 3 pins described
  • •Not yet checked by a person: land pattern vs datasheet, pin-1/orientation, 3D body vs drawing
Evidencedatasheet
Verified files! 2-1445098-3.kicad_sym! 2-1445098-3.kicad_mod! 2-1445098-3.step
Spot something wrong? Report it as an issue Propose a fix Records are signed by members of adom.
Overview Files Discover Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity
main
2-1445098-3 / 2-1445098-3.kicad_mod
HistoryDownload
Caleb Publish 0.1.1 69af80b 1d ago
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342
(footprint "2-1445098-3"
	(version 20241229)
	(generator "adom")
	(generator_version "1.0")
	(layer "F.Cu")
	(descr "TE Connectivity 2-1445098-3 Micro MATE-N-LOK header, 3 position, 3.00 mm pitch, right angle, plastic holddown; land pattern per TE customer drawing C-1445098 rev C sheet 2 (PCB layout for 3 position): 1.02 +0.20/-0 holes at 3.00, 3.00 +-0.08 holddown hole 4.32 from the contact row; board 1.57 mm")
	(tags "TE Micro MATE-N-LOK 1445098 3.00mm right angle header holddown THT")
	(property "Reference" "REF**"
		(at 0 -10.52 0)
		(layer "F.SilkS")
		(uuid "4b0f18ca-1917-44ab-9c3d-29566acf5eac")
		(effects
			(font (size 1 1) (thickness 0.15))
		)
	)
	(property "Value" "2-1445098-3"
		(at 0 3.34 0)
		(layer "F.Fab")
		(uuid "79e36aee-2495-4083-ac21-85ce220cd502")
		(effects
			(font (size 1 1) (thickness 0.15))
		)
	)
	(property "Datasheet" "https://www.te.com/commerce/DocumentDelivery/DDEController?Action=srchrtrv&DocNm=1445098&DocType=Customer+Drawing&DocLang=English&DocFormat=pdf"
		(at 0 0 0)
		(layer "F.Fab")
		(hide yes)
		(uuid "37ae024f-a6f1-4883-8b28-55b6ada00813")
		(effects
			(font (size 1.27 1.27) (thickness 0.15))
		)
	)
	(property "Description" "TE Micro MATE-N-LOK right-angle header, 3 position, 3.00 mm pitch, plastic holddown"
		(at 0 0 0)
		(layer "F.Fab")
		(hide yes)
		(uuid "37b6a7bc-d9a1-4c70-8cff-42450aa1f9bb")
		(effects
			(font (size 1.27 1.27) (thickness 0.15))
		)
	)
	(attr through_hole)
	(duplicate_pad_numbers_are_jumpers no)
	(fp_line
		(start -5 -8.92)
		(end 5 -8.92)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "ff91f40a-51d6-4258-9801-365230407ea2")
	)
	(fp_line
		(start 5 -8.92)
		(end 5 -5.865)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "3e1c1987-c415-4609-88f5-843392880d8b")
	)
	(fp_line
		(start 5 -5.865)
		(end 6.57 -5.865)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "4cb92822-4087-4e72-9a77-d2aff1f08060")
	)
	(fp_line
		(start 6.57 -5.865)
		(end 6.57 -3.395)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "7930cc07-2b25-437f-a5f2-16d4b4da66a4")
	)
	(fp_line
		(start 6.57 -3.395)
		(end 5 -3.395)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "d33621fd-72c8-4018-9ee3-6cfa4d959c8c")
	)
	(fp_line
		(start 5 -3.395)
		(end 5 0.32)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "06d8d1ab-291f-4ea0-b45f-16d5bdc66722")
	)
	(fp_line
		(start 5 0.32)
		(end -5 0.32)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "2b787244-dadf-490b-a759-c69c32f83036")
	)
	(fp_line
		(start -5 0.32)
		(end -5 -3.395)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "822151cf-bbba-4d88-92f8-dc889a93bbb3")
	)
	(fp_line
		(start -5 -3.395)
		(end -6.57 -3.395)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "52c5baff-17c6-4844-9cc2-892fcc351f8f")
	)
	(fp_line
		(start -6.57 -3.395)
		(end -6.57 -5.865)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "87630ce7-812a-4484-84a0-41644e206183")
	)
	(fp_line
		(start -6.57 -5.865)
		(end -5 -5.865)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "698a7bd7-cfec-4fd9-a746-6524e67f107c")
	)
	(fp_line
		(start -5 -5.865)
		(end -5 -8.92)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "6c525e07-1068-4f4f-adba-2144ad547848")
	)
	(fp_line
		(start -3.6 0.32)
		(end -3 -0.28)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "69425d04-78d8-4095-a642-adf382139dae")
	)
	(fp_line
		(start -3 -0.28)
		(end -2.4 0.32)
		(stroke (width 0.1) (type solid))
		(layer "F.Fab")
		(uuid "63aefee2-3073-4931-bb6b-17ca1fcde2b1")
	)
	(fp_circle
		(center 0 -4.32)
		(end 1.5 -4.32)
		(stroke (width 0.1) (type solid))
		(fill no)
		(layer "F.Fab")
		(uuid "047f0b8d-f5a2-4157-9f24-584ee9e7cca0")
	)
	(fp_text user "${REFERENCE}"
		(at 0 -4.96 0)
		(layer "F.Fab")
		(uuid "c22c564b-32b4-40dc-9fe0-9aa0c77ccf92")
		(effects
			(font (size 1 1) (thickness 0.15))
		)
	)
	(fp_line
		(start -5.11 -9.03)
		(end 5.11 -9.03)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "a2ae66f0-5468-4183-9af9-309553ce6a97")
	)
	(fp_line
		(start 5.11 -9.03)
		(end 5.11 -5.975)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "726a6abe-9af2-4b57-988d-3a094c0d96a4")
	)
	(fp_line
		(start 5.11 -5.975)
		(end 6.68 -5.975)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "01a71b3a-9dd9-4fb0-8f60-20f91aff2fc4")
	)
	(fp_line
		(start 6.68 -5.975)
		(end 6.68 -3.285)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "0a92e2ec-a91f-41cc-add4-8e15c21ef20b")
	)
	(fp_line
		(start 6.68 -3.285)
		(end 5.11 -3.285)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "bca81059-76ab-4d2e-aaf2-70b4b954c95b")
	)
	(fp_line
		(start 5.11 -3.285)
		(end 5.11 0.43)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "5517afca-a46f-4bea-b073-6ca1ea205ae4")
	)
	(fp_line
		(start -5.11 0.43)
		(end -5.11 -3.285)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "46e8f8c4-b4a3-4e38-85ee-868dcf81c1ca")
	)
	(fp_line
		(start -5.11 -3.285)
		(end -6.68 -3.285)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "6dc7968d-21c0-471f-adad-7c0dd894b034")
	)
	(fp_line
		(start -6.68 -3.285)
		(end -6.68 -5.975)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "512b0b7b-eb94-4fbf-a4e2-28783488594a")
	)
	(fp_line
		(start -6.68 -5.975)
		(end -5.11 -5.975)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "210667a4-a724-42de-9901-967905e63994")
	)
	(fp_line
		(start -5.11 -5.975)
		(end -5.11 -9.03)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "d6e8efc1-2207-4915-9b03-f46dd878886c")
	)
	(fp_line
		(start -5.11 0.43)
		(end -4.01247 0.43)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "a8479fa8-9836-4684-bdd5-e4e56c65772a")
	)
	(fp_line
		(start -1.98753 0.43)
		(end -1.01247 0.43)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "eb8ca09f-569c-494f-9b06-c8bdf13d686f")
	)
	(fp_line
		(start 1.01247 0.43)
		(end 1.98753 0.43)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "c2e57b08-5294-46b5-aca0-a68ce040a503")
	)
	(fp_line
		(start 4.01247 0.43)
		(end 5.11 0.43)
		(stroke (width 0.12) (type solid))
		(layer "F.SilkS")
		(uuid "cace0595-35a8-40f7-97ff-41ba30dc8295")
	)
	(fp_poly
		(pts (xy -3 1.2) (xy -3.45 1.85) (xy -2.55 1.85))
		(stroke (width 0.12) (type solid))
		(fill yes)
		(layer "F.SilkS")
		(uuid "8e79c4f2-cc44-45e7-aad5-cc7ac05f0b82")
	)
	(fp_line
		(start -7.07 -9.42)
		(end 7.07 -9.42)
		(stroke (width 0.05) (type solid))
		(layer "F.CrtYd")
		(uuid "a2bc2645-14d3-4ad5-8941-3bbb2234ce7c")
	)
	(fp_line
		(start 7.07 -9.42)
		(end 7.07 1.44)
		(stroke (width 0.05) (type solid))
		(layer "F.CrtYd")
		(uuid "30a7e704-dd16-4d2c-98c5-390c7314568d")
	)
	(fp_line
		(start 7.07 1.44)
		(end -7.07 1.44)
		(stroke (width 0.05) (type solid))
		(layer "F.CrtYd")
		(uuid "041be420-839e-4e4f-aaa3-dafbe3a6a8a3")
	)
	(fp_line
		(start -7.07 1.44)
		(end -7.07 -9.42)
		(stroke (width 0.05) (type solid))
		(layer "F.CrtYd")
		(uuid "9bb2f2a0-c6f8-4d4e-aaa6-9e91762a8559")
	)
	(pad "1" thru_hole roundrect
		(at -3 0)
		(size 1.8 1.8)
		(drill 1.12)
		(layers "*.Cu" "*.Mask")
		(roundrect_rratio 0.138889)
		(remove_unused_layers no)
		(uuid "8ce60347-4faa-46d8-bf79-272c0285bd97")
	)
	(pad "2" thru_hole circle
		(at 0 0)
		(size 1.8 1.8)
		(drill 1.12)
		(layers "*.Cu" "*.Mask")
		(remove_unused_layers no)
		(uuid "817672dc-e817-461b-881a-aa0bab717e8a")
	)
	(pad "3" thru_hole circle
		(at 3 0)
		(size 1.8 1.8)
		(drill 1.12)
		(layers "*.Cu" "*.Mask")
		(remove_unused_layers no)
		(uuid "925ec679-4f6c-4846-a0c8-61b584a56f76")
	)
	(pad "" np_thru_hole circle
		(at 0 -4.32)
		(size 3 3)
		(drill 3)
		(layers "*.Cu" "*.Mask")
		(uuid "a94c8708-400a-4c95-8931-8c5bb204ef52")
	)
	(embedded_fonts no)
	(model "${KIPRJMOD}/2-1445098-3.step"
		(offset
			(xyz 0 0 0)
		)
		(scale
			(xyz 1 1 1)
		)
		(rotate
			(xyz 0 0 0)
		)
	)
)