main
Ray
Publish 0.1.0
0c59b52
1EDC20I12AHXUMA1
Infineon Technologies · Gate Drivers · SOIC-8-300mil
1EDC20I12AHXUMA1 from Infineon Technologies, in a SOIC-8-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC1 | power_in | Logic input supply voltage with a 3.1 V to 17 V operating range (3.3 V up to 15 V wide operating range as stated in the pin description), and an 18.0 V absolute maximum. |
| 2 | IN+ | input | Non-inverted driver input (active high) that controls the output when IN- is low; it has an internal weak pull-down favoring the off-state and a minimum pulse width filter against noise. |
| 3 | IN- | input | Inverted driver input (active low) that controls the output when IN+ is high; it has an internal weak pull-up favoring the off-state and a minimum pulse width filter against noise. |
| 4 | GND1 | power_in | Ground connection of the input (logic) circuit. |
| 5 | GND2 | power_in | Reference ground of the output driving circuit; in a bipolar supply configuration it is connected to the negative supply voltage. |
| 6 | VCC2 | power_in | Positive power supply pin of the output driving circuit (operating range 13 V to 35 V referred to GND2); a proper blocking capacitor must be placed close to this pin. |
| 7 | OUT+ | output | Driver source output that turns on the external IGBT by switching to VCC2 in the on-state; it can sink approx. 100 mA during turn-off and is turned off at a UVLO event. |
| 8 | OUT- | output | Driver sink output that turns off the external IGBT by switching to GND2 in the off-state; during UVLO an active shut-down keeps the output at a low level. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | SOIC-8-300mil |
| Category | Motor Driver ICs |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply output side | VVCC2 | -0.3 | 40 | V | 10 | ||
| Positive power supply input side | VVCC1 | -0.3 | 18 | V | 10 | ||
| Logic input voltages (IN+,IN-) | VLogicIN | -0.3 | 18 | V | 10 | ||
| Input to output isolation voltage (GND2) | VGND2 | -1200 | 1200 | V | GND2 - GND1 | 10 | |
| Junction temperature | TJ | -40 | 150 | °C | 10 | ||
| Storage temperature | TS | -55 | 150 | °C | 10 | ||
| Comparative tracking index | CTI | 400 | IEC 60601-1: Material group II | 10 | |||
| Power dissipation (Input side) | PD,IN | 25 | mW | TA = 25°C | 10 | ||
| Power dissipation (Output side) | PD,OUT | 400 | mW | TA = 25°C | 10 | ||
| Thermal resistance (Input side) | RTHJA,IN | 145 | K/W | TA = 85°C | 10 | ||
| Thermal resistance (Output side) | RTHJA,OUT | 165 | K/W | TA = 85°C | 10 | ||
| ESD capability HBM | VESD,HBM | 2 | kV | Human body model | 10 | ||
| ESD capability CDM | VESD,CDM | 1 | kV | Charged device model | 10 | ||
| Power supply output side (operating) | VVCC2 | 13 | 35 | V | note 5: with respect to GND2 | 11 | |
| Power supply input side (operating) | VVCC1 | 3.1 | 17 | V | 11 | ||
| Logic input voltages (IN+,IN-) (operating) | VLogicIN | -0.3 | 17 | V | 11 | ||
| Switching frequency | fsw | 1 | MHz | do not exceed max. power dissipation | 11 | ||
| Ambient temperature | TA | -40 | 125 | °C | 11 | ||
| Thermal coefficient, junction-top | Ψth,jt | 4.8 | K/W | TA = 85°C | 11 | ||
| Common mode transient immunity (CMTI) | /dVISO/dt/ | 100 | kV/μs | at 1000 V | 11 | ||
| UVLO threshold input chip (rising) | VUVLOH1 | 2.85 | 3.1 | V | 11 | ||
| UVLO threshold input chip (falling) | VUVLOL1 | 2.55 | 2.75 | V | 11 | ||
| UVLO hysteresis input chip | VHYS1 | 0.09 | 0.1 | V | 11 | ||
| UVLO threshold output chip (rising, IGBT supply) | VUVLOH2 | 12 | 12.7 | V | note 8: with respect to GND2 | 11 | |
| UVLO threshold output chip (falling, IGBT supply) | VUVLOL2 | 10.5 | 11.1 | V | note 8: with respect to GND2 | 11 | |
| UVLO hysteresis output chip | VHYS2 | 0.7 | 0.85 | V | 12 | ||
| Quiescent current input chip | IQ1 | 0.65 | 1 | mA | VVCC1 = 5 V, IN+ = High, IN- = Low => OUT = High | 12 | |
| Quiescent current output chip | IQ2 | 1.2 | 2 | mA | VVCC2 = 15 V, IN+ = High, IN- = Low => OUT = High | 12 | |
| IN+,IN- low input voltage | VIN+L, VIN-L | 1.5 | V | VVCC1 = 5.0 V | 13 | ||
| IN+,IN- high input voltage | VIN+H, VIN-H | 3.5 | V | VVCC1 = 5.0 V | 13 | ||
| IN- input current | IIN- | 70 | 200 | μA | VVCC1 = 5.0 V, VIN- = GND1 | 13 | |
| IN+ input current | IIN+ | 70 | 200 | μA | VVCC1 = 5.0 V, VIN+ = VVCC1 | 13 | |
| High level output peak current (source) | IOUT+,PEAK | 2 | 4 | A | IN+ = High, IN- = Low, VVCC2 = 15 V | 13 | |
| Low level output peak current (sink) | IOUT-,PEAK | 2 | 3.5 | A | IN+ = Low, IN- = Low, VVCC2 = 15 V | 13 | |
| Clamping voltage (OUT+) | VCLPout | 0.9 | 1.3 | V | IN+ = High, IN- = Low, OUT = High; IOUT = 500 mA, pulse test tCLPmax = 10 μs | 14 | |
| Input IN to output propagation delay ON | TPDON | 270 | 300 | 330 | ns | CLOAD = 100 pF, VIN+ = 50%, VOUT=50% @25°C | 14 |
| Input IN to output propagation delay OFF | TPDOFF | 270 | 300 | 330 | ns | CLOAD = 100 pF, VIN+ = 50%, VOUT=50% @25°C | 14 |
| Input IN to output propagation delay distortion (TPDOFF - TPDON) | TPDISTO | -30 | 5 | 40 | ns | 14 | |
| Input pulse suppression time IN+, IN- | TMININ+, TMININ- | 230 | 240 | ns | 14 | ||
| Input IN to output propagation delay ON variation due to temp | TPDONt | 14 | ns | CLOAD = 100 pF, VIN+ = 50%, VOUT=50% | 15 | ||
| Input IN to output propagation delay OFF variation due to temp | TPDONt | 14 | ns | 15 | |||
| Input IN to output propagation delay distortion variation due to temp (TPDOFF-TPDON) | TPDISTOt | 8 | ns | 15 | |||
| Rise time | TRISE | 5 | 10 | 20 | ns | CLOAD = 1 nF | 15 |
| Fall time | TFALL | 4 | 9 | 19 | ns | VL20%, VH 80% | 15 |
| Active shut down voltage | VACTSD | 2 | 2.3 | V | IOUT-/IOUT-,PEAK=0.1, VCC2 open | 15 |
CAD (KiCad official)
- Symbol:
1EDC20I12AHXUMA1 - Footprint:
Package_SO:SOIC-8_7.5x5.85mm_P1.27mm - 3D model: SOIC-8-300mil (KiCad packages3D, STEP)
- 3D model files:
1edc20i12ahxuma1-etched.step/1edc20i12ahxuma1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);1edc20i12ahxuma1.step/1edc20i12ahxuma1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Infineon Technologies datasheet (18 pp, sha256
b02b03648102aedc, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# 1EDC20I12AHXUMA1
**Infineon Technologies** · Gate Drivers · SOIC-8-300mil
1EDC20I12AHXUMA1 from Infineon Technologies, in a SOIC-8-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VCC1 | power_in | Logic input supply voltage with a 3.1 V to 17 V operating range (3.3 V up to 15 V wide operating range as stated in the pin description), and an 18.0 V absolute maximum. |
| 2 | IN+ | input | Non-inverted driver input (active high) that controls the output when IN- is low; it has an internal weak pull-down favoring the off-state and a minimum pulse width filter against noise. |
| 3 | IN- | input | Inverted driver input (active low) that controls the output when IN+ is high; it has an internal weak pull-up favoring the off-state and a minimum pulse width filter against noise. |
| 4 | GND1 | power_in | Ground connection of the input (logic) circuit. |
| 5 | GND2 | power_in | Reference ground of the output driving circuit; in a bipolar supply configuration it is connected to the negative supply voltage. |
| 6 | VCC2 | power_in | Positive power supply pin of the output driving circuit (operating range 13 V to 35 V referred to GND2); a proper blocking capacitor must be placed close to this pin. |
| 7 | OUT+ | output | Driver source output that turns on the external IGBT by switching to VCC2 in the on-state; it can sink approx. 100 mA during turn-off and is turned off at a UVLO event. |
| 8 | OUT- | output | Driver sink output that turns off the external IGBT by switching to GND2 in the off-state; during UVLO an active shut-down keeps the output at a low level. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Infineon Technologies |
| Package | SOIC-8-300mil |
| Category | Motor Driver ICs |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply output side | VVCC2 | -0.3 | | 40 | V | | 10 |
| Positive power supply input side | VVCC1 | -0.3 | | 18 | V | | 10 |
| Logic input voltages (IN+,IN-) | VLogicIN | -0.3 | | 18 | V | | 10 |
| Input to output isolation voltage (GND2) | VGND2 | -1200 | | 1200 | V | GND2 - GND1 | 10 |
| Junction temperature | TJ | -40 | | 150 | °C | | 10 |
| Storage temperature | TS | -55 | | 150 | °C | | 10 |
| Comparative tracking index | CTI | 400 | | | | IEC 60601-1: Material group II | 10 |
| Power dissipation (Input side) | PD,IN | | | 25 | mW | TA = 25°C | 10 |
| Power dissipation (Output side) | PD,OUT | | | 400 | mW | TA = 25°C | 10 |
| Thermal resistance (Input side) | RTHJA,IN | | | 145 | K/W | TA = 85°C | 10 |
| Thermal resistance (Output side) | RTHJA,OUT | | | 165 | K/W | TA = 85°C | 10 |
| ESD capability HBM | VESD,HBM | | | 2 | kV | Human body model | 10 |
| ESD capability CDM | VESD,CDM | | | 1 | kV | Charged device model | 10 |
| Power supply output side (operating) | VVCC2 | 13 | | 35 | V | note 5: with respect to GND2 | 11 |
| Power supply input side (operating) | VVCC1 | 3.1 | | 17 | V | | 11 |
| Logic input voltages (IN+,IN-) (operating) | VLogicIN | -0.3 | | 17 | V | | 11 |
| Switching frequency | fsw | | | 1 | MHz | do not exceed max. power dissipation | 11 |
| Ambient temperature | TA | -40 | | 125 | °C | | 11 |
| Thermal coefficient, junction-top | Ψth,jt | | | 4.8 | K/W | TA = 85°C | 11 |
| Common mode transient immunity (CMTI) | /dVISO/dt/ | | | 100 | kV/μs | at 1000 V | 11 |
| UVLO threshold input chip (rising) | VUVLOH1 | | 2.85 | 3.1 | V | | 11 |
| UVLO threshold input chip (falling) | VUVLOL1 | 2.55 | 2.75 | | V | | 11 |
| UVLO hysteresis input chip | VHYS1 | 0.09 | 0.1 | | V | | 11 |
| UVLO threshold output chip (rising, IGBT supply) | VUVLOH2 | | 12 | 12.7 | V | note 8: with respect to GND2 | 11 |
| UVLO threshold output chip (falling, IGBT supply) | VUVLOL2 | 10.5 | 11.1 | | V | note 8: with respect to GND2 | 11 |
| UVLO hysteresis output chip | VHYS2 | 0.7 | 0.85 | | V | | 12 |
| Quiescent current input chip | IQ1 | | 0.65 | 1 | mA | VVCC1 = 5 V, IN+ = High, IN- = Low => OUT = High | 12 |
| Quiescent current output chip | IQ2 | | 1.2 | 2 | mA | VVCC2 = 15 V, IN+ = High, IN- = Low => OUT = High | 12 |
| IN+,IN- low input voltage | VIN+L, VIN-L | | | 1.5 | V | VVCC1 = 5.0 V | 13 |
| IN+,IN- high input voltage | VIN+H, VIN-H | 3.5 | | | V | VVCC1 = 5.0 V | 13 |
| IN- input current | IIN- | | 70 | 200 | μA | VVCC1 = 5.0 V, VIN- = GND1 | 13 |
| IN+ input current | IIN+ | | 70 | 200 | μA | VVCC1 = 5.0 V, VIN+ = VVCC1 | 13 |
| High level output peak current (source) | IOUT+,PEAK | 2 | 4 | | A | IN+ = High, IN- = Low, VVCC2 = 15 V | 13 |
| Low level output peak current (sink) | IOUT-,PEAK | 2 | 3.5 | | A | IN+ = Low, IN- = Low, VVCC2 = 15 V | 13 |
| Clamping voltage (OUT+) | VCLPout | | 0.9 | 1.3 | V | IN+ = High, IN- = Low, OUT = High; IOUT = 500 mA, pulse test tCLPmax = 10 μs | 14 |
| Input IN to output propagation delay ON | TPDON | 270 | 300 | 330 | ns | CLOAD = 100 pF, VIN+ = 50%, VOUT=50% @25°C | 14 |
| Input IN to output propagation delay OFF | TPDOFF | 270 | 300 | 330 | ns | CLOAD = 100 pF, VIN+ = 50%, VOUT=50% @25°C | 14 |
| Input IN to output propagation delay distortion (TPDOFF - TPDON) | TPDISTO | -30 | 5 | 40 | ns | | 14 |
| Input pulse suppression time IN+, IN- | TMININ+, TMININ- | 230 | 240 | | ns | | 14 |
| Input IN to output propagation delay ON variation due to temp | TPDONt | | | 14 | ns | CLOAD = 100 pF, VIN+ = 50%, VOUT=50% | 15 |
| Input IN to output propagation delay OFF variation due to temp | TPDONt | | | 14 | ns | | 15 |
| Input IN to output propagation delay distortion variation due to temp (TPDOFF-TPDON) | TPDISTOt | | | 8 | ns | | 15 |
| Rise time | TRISE | 5 | 10 | 20 | ns | CLOAD = 1 nF | 15 |
| Fall time | TFALL | 4 | 9 | 19 | ns | VL20%, VH 80% | 15 |
| Active shut down voltage | VACTSD | | 2 | 2.3 | V | IOUT-/IOUT-,PEAK=0.1, VCC2 open | 15 |
## CAD (KiCad official)
- Symbol: `1EDC20I12AHXUMA1`
- Footprint: `Package_SO:SOIC-8_7.5x5.85mm_P1.27mm`
- 3D model: SOIC-8-300mil (KiCad packages3D, STEP)
- 3D model files: `1edc20i12ahxuma1-etched.step` / `1edc20i12ahxuma1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `1edc20i12ahxuma1.step` / `1edc20i12ahxuma1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Infineon Technologies datasheet](docs/1edc20i12ahxuma1-datasheet.pdf) (18 pp, sha256 `b02b03648102aedc`, retrieved 2026-11-11, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/1edc20i12ahxuma1-datasheet.pdf)