3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdown1339-31DVGI8
RENESAS · Real-time Clocks (RTC) · MSOP-8
1339-31DVGI8 from RENESAS, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Connection for a standard 32.768 kHz quartz crystal with 7 pF specified load capacitance, or the input for an external 32.768 kHz oscillator signal (X2 left floating). |
| 2 | X2 | passive | Connection for the 32.768 kHz quartz crystal; left floating when an external oscillator drives X1. |
| 3 | VBACKUP | power_in | Backup supply input held between 1.3 V and 3.7 V, connectable to a primary lithium cell, rechargeable cell or super cap charged by the trickle charger; connect to ground if no backup supply is used. |
| 4 | GND | power_in | Ground connection; DC power is provided to the device on these pins. |
| 5 | SDA | bidirectional | I2C serial data input/output, open-drain, requires an external pull-up resistor (2 kΩ typical). |
| 6 | SCL | input | I2C serial clock input used to synchronize data movement, requires an external pull-up resistor (2 kΩ typical). |
| 7 | SQW/INT | output | Programmable square-wave or interrupt output, open-drain, requires an external pull-up resistor (10 kΩ typical). |
| 8 | VCC | power_in | Primary power supply; when voltage is within normal limits the device is fully accessible for read and write. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | MSOP-8 |
| Category | Clock and Timing |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage on all inputs and outputs | -0.3 | 6 | V | All Inputs and Outputs | 14 | ||
| Storage Temperature | -55 | 125 | °C | 14 | |||
| Soldering Temperature | 260 | °C | 14 | ||||
| Ambient Operating Temperature | TA | -40 | 85 | °C | 14 | ||
| Backup Supply Voltage | VBACKUP | 1.3 | 3 | 3.7 | V | 14 | |
| Pull-up Resistor Voltage (SQW/INT, SDA, SCL) | VPU | 5.5 | V | VCC = 0V | 14 | ||
| Supply Voltage IDT1339-31 | VCC | 3.3 | 5.5 | V | Note A (no backup supply); min printed on VPF line | 14 | |
| Power Fail Voltage IDT1339-31 | VPF | 2.45 | 2.7 | 2.97 | V | Note B | 14 |
| Input Leakage | ILI | 1 | µA | Note 2 (SCL only) | 15 | ||
| I/O Leakage | ILO | 1 | µA | Note 3 (SDA and SQW/INT) | 15 | ||
| Logic 0 Out current IDT1339-31 | IOL | 3 | mA | VOL = 0.4; VCC > VCC Min.; VCC > 2.0 V; Note 3 | 15 | ||
| VCC Active Current | ICCA | 450 | µA | Note 4 | 15 | ||
| VCC Standby Current | ICCS | 80 | 150 | µA | VCC < 3.63 V; Note 5 | 15 | |
| VCC Standby Current | ICCS | 200 | µA | 3.63 V < VCC < 5.5 V; Note 5 | 15 | ||
| Trickle-charger Resistor R1 | R1 | 250 | Ω | 10h = A5h, VCC = Typ, VBACKUP = 0V; Note 6 | 15 | ||
| Trickle-charger Resistor R2 | R2 | 2000 | Ω | 10h = A6h, VCC = Typ, VBACKUP = 0V | 15 | ||
| Trickle-charger Resistor R3 | R3 | 4000 | Ω | 10h = A7h, VCC = Typ, VBACKUP = 0V | 15 | ||
| VBACKUP Leakage Current | IBKLKG | 25 | 100 | nA | 15 | ||
| VBACKUP Current EOSC = 0, SQW Off | IBKOSC | 800 | 1200 | nA | Note 7; VCC = 0V | 15 | |
| VBACKUP Current EOSC = 0, SQW On | IBKSQW | 1025 | 1400 | nA | Note 7; VCC = 0V | 15 | |
| VBACKUP Current EOSC = 1 | IBKDR | 120 | 300 | nA | Note 7; VCC = 0V | 15 | |
| Recovery at Power-up | tREC | 2 | ms | Note 1 | 5 | ||
| VCC Fall Time; VPF(MAX) to VPF(MIN) | tVCCF | 3 | ms | Note 2 | 5 | ||
| VCC Rise Time; VPF(MIN) to VPF(MAX) | tVCCR | 0 | µs | 5 | |||
| SCL Clock Frequency | fSCL | 100 | 400 | kHz | Fast Mode | 16 | |
| SCL Clock Frequency | fSCL | 100 | kHz | Standard Mode | 16 | ||
| Bus Free Time STOP to START | tBUF | 1.3 | µs | Fast Mode | 16 | ||
| Bus Free Time STOP to START | tBUF | 4.7 | µs | Standard Mode | 16 | ||
| Hold Time (Repeated) START | tHD:STA | 0.6 | µs | Fast Mode; Note 8 | 16 | ||
| Hold Time (Repeated) START | tHD:STA | 4 | µs | Standard Mode; Note 8 | 16 | ||
| Low Period of SCL Clock | tLOW | 1.3 | µs | Fast Mode | 16 | ||
| Low Period of SCL Clock | tLOW | 4.7 | µs | Standard Mode | 16 | ||
| High Period of SCL Clock | tHIGH | 0.6 | µs | Fast Mode | 16 | ||
| High Period of SCL Clock | tHIGH | 4 | µs | Standard Mode | 16 | ||
| Setup Time for Repeated START | tSU:STA | 0.6 | µs | Fast Mode | 16 | ||
| Setup Time for Repeated START | tSU:STA | 4.7 | µs | Standard Mode | 16 | ||
| Data Hold Time | tHD:DAT | 0 | 0.9 | µs | Fast Mode; Notes 9, 10 | 16 | |
| Data Hold Time | tHD:DAT | 0 | µs | Standard Mode; Notes 9, 10 | 16 | ||
| Data Setup Time | tSU:DAT | 100 | ns | Fast Mode; Note 11 | 16 | ||
| Data Setup Time | tSU:DAT | 250 | ns | Standard Mode; Note 11 | 16 | ||
| Rise Time of SDA and SCL | tR | 300 | ns | Fast Mode; Note 12; min 20 + 0.1CB | 16 | ||
| Rise Time of SDA and SCL | tR | 1000 | ns | Standard Mode; Note 12; min 20 + 0.1CB | 16 | ||
| Fall Time of SDA and SCL | tF | 300 | ns | Fast Mode; Note 12; min 20 + 0.1CB | 16 | ||
| Setup Time for STOP Condition | tSU:STO | 0.6 | µs | Fast Mode | 16 | ||
| Setup Time for STOP Condition | tSU:STO | 4 | µs | Standard Mode | 16 | ||
| Capacitive Load for Each Bus Line | CB | 400 | pF | Note 12 | 16 | ||
| I/O Capacitance (SDA, SCL) | CI/O | 10 | pF | Note 13 | 16 | ||
| Oscillator Stop Flag Delay | tOSF | 100 | ms | Note 14 | 16 | ||
| Thermal Resistance Junction to Ambient (8 MSOP) | θJA | 95 | °C/W | Still air | 19 | ||
| Thermal Resistance Junction to Case (8 MSOP) | θJC | 48 | °C/W | 19 |
CAD (KiCad official)
- Symbol:
1339-31DVGI8 - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
1339-31dvgi8-etched.step/1339-31dvgi8-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);1339-31dvgi8.step/1339-31dvgi8.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (27 pp, sha256
7d5dd89505c58e9e, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).