component
TPS54060DGQR
Public Made by Adomby adom
Texas Instruments DC-DC Converters, MSOP-10-EP. Pinout extracted from the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads only if this page sits in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads only if this page sits in the background.
PCB Footprint
Open full view ↗Loads on click. Unloads only if this page sits in the background.
Datasheet
Open in new tab ↗Loads on click. Unloads only if this page sits in the background.
Contents
README
markdownTPS54060DGQR
Texas Instruments · DC-DC Converters · MSOP-10-EP
TPS54060DGQR from Texas Instruments, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | passive | Bootstrap capacitor node. A capacitor is required between BOOT and PH to supply gate drive for the internal high-side NMOS. If the BOOT-PH voltage falls below the required minimum the output is forced off for one cycle to refresh the bootstrap capacitor. Absolute max 73V to GND, 8V BOOT-PH. |
| 2 | VIN | power_in | Input supply voltage, 3.5V to 60V operating range (absolute max 65V). Bypass locally to GND with a low-ESR ceramic capacitor. |
| 3 | EN | input | Enable pin with internal pull-up current source. Pull below ~1.2V to disable; float or pull high to enable. Two external resistors on EN program the input UVLO threshold and hysteresis. Absolute max -0.3 to 5V. |
| 4 | SS/TR | input | Slow-start and tracking. An external capacitor on this pin sets the output voltage rise time (charge current ~2 µA). The pin can also be driven for sequencing/tracking; voltage on SS/TR overrides the internal 0.8V reference when lower. |
| 5 | RT/CLK | bidirectional | Resistor timing and external clock input. An external resistor to GND sets the switching frequency (100kHz-2.5MHz). Pulling above the PLL upper threshold converts the pin to a synchronization clock input for the internal PLL. Absolute max -0.3 to 3.6V. |
| 6 | PWRGD | output | Open-drain power-good output. Asserts low when the output voltage is out of the 93%-107% window, or during thermal shutdown, dropout, over-voltage, or EN shutdown. Requires an external pull-up resistor. Absolute max -0.3 to 6V. |
| 7 | VSENSE | input | Inverting input of the transconductance (gm) error amplifier; feedback node compared to the internal 0.8V reference. Connect an external resistor divider from VOUT to set the regulation voltage. |
| 8 | COMP | output | Error amplifier output and input to the output switch current comparator. Connect the frequency compensation network (R-C or R-C-C) from COMP to GND. |
| 9 | GND | power_in | Device ground. Must be electrically connected to the exposed thermal PowerPAD on the PCB for proper operation. |
| 10 | PH | power_out | Switch node. Source of the internal high-side power MOSFET; connect to the external inductor and catch (Schottky) diode. Absolute max -0.6 to 65V (-2 to 65V for 10ns transients). |
| 11 | POWERPAD | power_in | Exposed thermal pad on the package bottom. Must be soldered to the PCB ground plane and electrically connected to GND (pin 9) for proper thermal and electrical operation. PAD-to-GND absolute max ±200 mV. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | MSOP-10-EP |
| Category | PMIC |
| Pins | 11 |
Ordering variants
Same part, different packaging or reel option.
TPS54060DGQRTPS54060DGQRDRCTPS54060DGQRDRCR
CAD (KiCad official)
- Symbol:
TPS54060DGQR - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
tps54060dgqr-etched.step/tps54060dgqr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);tps54060dgqr.step/tps54060dgqr.glbare the bare package body.
3D model downloads
Two STEP files. Same geometry, different body top:
| File | Size | Use it when |
|---|---|---|
tps54060dgqr.step |
151 KB | You want the bare part, or you mark your own boards. |
tps54060dgqr-etched.step |
2.9 MB | You want the part with TPS54060DGQR already on it. |
The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 694 faces against 182 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (49 pp, sha256
3ba50924639f637b, retrieved 2026-08-17, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).