component
M24M01-RMN6TP
Public Unreviewedby Ray
STMicroelectronics EEPROM, SOIC-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads on click. Unloads when scrolled away or the tab is hidden.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads on click. Unloads when scrolled away or the tab is hidden.
PCB Footprint
Open full view ↗Loads on click. Unloads when scrolled away or the tab is hidden.
Datasheet
Open in new tab ↗Loads on click. Unloads when scrolled away or the tab is hidden.
Contents
README
markdownM24M01-RMN6TP
STMicroelectronics · EEPROM · SOIC-8
M24M01-RMN6TP from STMicroelectronics, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DU | unconnected | Don't Use. No signal should be applied to this pin; if connected, it must be tied to VSS. Reserved by the manufacturer for test/factory use. |
| 2 | E1 | input | Chip Enable input bit 1. Sets bit b2 of the 7-bit I2C device select code. Must be tied to VCC or VSS; when left floating it is read as low (0). Enables up to 4 M24M01 devices on a single I2C bus. |
| 3 | E2 | input | Chip Enable input bit 2. Sets bit b3 of the 7-bit I2C device select code. Must be tied to VCC or VSS; when left floating it is read as low (0). |
| 4 | VSS | power_in | Ground reference for the VCC supply. Connect to the system 0 V rail with a low-inductance path; place the VCC decoupling capacitor (10 nF-100 nF) close to VCC/VSS pins. |
| 5 | SDA | bidirectional | Serial Data line (I2C). Open-drain input/output used to transfer data in and out of the device; may be wire-OR'ed with other open-drain/open-collector signals. Requires an external pull-up resistor to VCC sized for the bus capacitance. |
| 6 | SCL | input | Serial Clock input (I2C). Strobes data on SDA (input on rising edge, output changes on falling edge). Supports 100 kHz, 400 kHz, and 1 MHz I2C bus modes. Requires an external pull-up resistor to VCC. |
| 7 | WC | input | Write Control, active low (WC). When driven high, all write operations to the memory array are inhibited (device-select and address bytes are still ACK'd, but data bytes are not ACK'd). When driven low or left floating, writes are enabled. |
| 8 | VCC | power_in | Supply voltage. Operating range 1.7 V to 5.5 V (M24M01-DF grade) or 1.8 V to 5.5 V (M24M01-R grade). Decouple with a 10 nF-100 nF capacitor placed close to the VCC/VSS pins. A power-on-reset (POR) circuit inhibits writes until VCC is valid. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | SOIC-8 |
| Category | Memory |
| Pins | 8 |
Ordering variants
Same part, different packaging or reel option.
M24M01-RMN6TPM24M01-RMN6PM24M01-RMN6TPDFMN6TPM24M01-RMN6TPDFMN6PM24M01-RMN6TPRDW6TPM24M01-RMN6TPRDW6PM24M01-RMN6TPDFDW6TPM24M01-RMN6TPDFDW6PM24M01-RMN6TPDFCS6TPM24M01-RMN6TPDFCS6TP/K
CAD (KiCad official)
- Symbol:
M24M01-RMN6TP - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
3D model downloads
Two STEP files. Same geometry, different body top:
| File | Size | Use it when |
|---|---|---|
m24m01-rmn6tp.step |
122 KB | You want the bare part, or you mark your own boards. |
m24m01-rmn6tp-etched.step |
2.2 MB | You want the part with M24M01-RMN6TP already on it. |
The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 568 faces against 147 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (41 pp, sha256
1cc733fc15649559, retrieved 2026-08-17, tier: manufacturer) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).