LM293DR2G from onsemi, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	OUTA	output	Open-collector output of comparator A. Sinks up to 16 mA typical (6 mA min) with VOL ≤ 400 mV at 4 mA; requires an external pull-up resistor to VCC (or another supply up to 36 V). Output leakage 0.1 nA typ.
2	IN-A	input	Inverting input of comparator A. Common-mode range 0 V to (VCC − 1.5 V); input bias current 20 nA typ (250 nA max), input offset current 5 nA typ. Must not go more than 0.3 V below the negative supply.
3	IN+A	input	Non-inverting input of comparator A. Common-mode range 0 V to (VCC − 1.5 V); input bias current 20 nA typ. Differential input voltage may equal the full supply voltage.
4	GND	power_in	Negative supply / ground. Tied to 0 V in single-supply operation, or to the negative rail (down to −18 V) in split-supply operation.
5	IN+B	input	Non-inverting input of comparator B. Common-mode range 0 V to (VCC − 1.5 V); input bias current 20 nA typ (250 nA max). Differential input voltage may equal the full supply voltage.
6	IN-B	input	Inverting input of comparator B. Common-mode range 0 V to (VCC − 1.5 V); input bias current 20 nA typ. Must not go more than 0.3 V below the negative supply.
7	OUTB	output	Open-collector output of comparator B. Sinks up to 16 mA typical (6 mA min) with VOL ≤ 400 mV at 4 mA; requires an external pull-up resistor. Output leakage 0.1 nA typ.
8	VCC	power_in	Positive supply. Single-supply range 2.0 V to 36 V, or ±1.0 V to ±18 V split supply. Typical supply current 0.4 mA (1.0 mA max) for both comparators, independent of supply voltage.

Key specifications

Parameter	Value
Manufacturer	onsemi
Package	SOIC-8
Category	Op-amp/Cmp
Pins	8

Ordering variants

Same part, different packaging or reel option.

LM293DR2G
LM293DR2GDG
LM293DR2GN
LM293DR2GDM
LM293DR2GDMR2

CAD (KiCad official)

Symbol: LM293DR2G
Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
3D model: SOIC-8 (KiCad packages3D, STEP)

3D model downloads

Two STEP files. Same geometry, different body top:

File	Size	Use it when
`lm293dr2g.step`	122 KB	You want the bare part, or you mark your own boards.
`lm293dr2g-etched.step`	2.1 MB	You want the part with `LM293DR2G` already on it.

The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 509 faces against 147 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: onsemi datasheet (13 pp, sha256 b87721993d627de6, retrieved 2026-08-17, tier: manufacturer)
Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF