component
CP2102
Public Unreviewedby adom
Silicon Labs single-chip USB-to-UART bridge, QFN-28. Integrated USB, regulator, clock, EEPROM. Up to 1 Mbps. Datasheet-verified.
← Commit history
Publish 0.1.0
8 files changed
+824−9
README.md+69−2@@ -1,5 +1,72 @@ # CP2102 -USB to UART bridge, up to 1Mbps, QFN-28+**Silicon Labs** · USB-to-UART bridge · QFN-28 -The CP2102 is a USB to UART bridge controller from Silicon Labs. Supports baud rates up to 1Mbps with integrated USB transceiver and clock. Widely used in development boards and serial adapters.+The original single-chip USB-to-UART bridge from Silicon Labs, in QFN-28, and one of the most common ways to put a serial port on USB. Everything is on-chip: the USB 2.0 full-speed transceiver, a 3.3 V regulator, the oscillator, and a 1 KB EEPROM holding the USB descriptors, so the whole design is the chip plus a couple of capacitors. It presents a virtual COM port to the host and moves data at up to 1 Mbps, with the standard modem-control lines. It powers a huge share of the cheap USB-TTL adapters. The newer CP2102N adds higher rates and GPIO. Runs from USB 5 V or 3.3 V.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | DCD | input | Data Carrier Detect control input (active low). RS-232 modem control input; can be left unconnected when not used. |+| 2 | RI | input | Ring Indicator control input (active low). RS-232 modem control input; can be left unconnected when not used. |+| 3 | GND | power_in | Ground reference. Also connect the exposed center pad of the QFN-28 to GND. |+| 4 | D+ | bidirectional | USB D+ data line. Connects directly to the USB connector D+ pin; integrated 1.5 kΩ pull-up for full-speed enumeration. |+| 5 | D- | bidirectional | USB D- data line. Connects directly to the USB connector D- pin. |+| 6 | VDD | power_in | 3.0-3.6 V power supply input and 3.3 V voltage regulator output. When the on-chip regulator is used (REGIN from VBUS), VDD is driven by the regulator and requires a 4.7 µF + 0.1 µF decoupling capacitor to GND. |+| 7 | REGIN | power_in | 5 V input to the on-chip voltage regulator (typ. 4.0-5.25 V). Requires a 1.0 µF + 0.1 µF decoupling capacitor to GND. |+| 8 | VBUS | input | VBUS sense input. Connect to the VBUS signal of the USB network; a 5 V level indicates a USB connection. Detection threshold typ. 1.8 V. |+| 9 | RST | bidirectional | Device reset (active low). Open-drain output of the internal POR/VDD monitor; an external source can initiate a system reset by driving this pin low for at least 15 µs. |+| 10 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 11 | SUSPEND | output | Active-low suspend indicator. Driven low when the CP2102/9 enters the USB suspend state (inverse of SUSPEND). Floats high momentarily during reset; a 10 kΩ pulldown to GND is recommended to hold it low on power-up. |+| 12 | SUSPEND | output | Active-high suspend indicator. Driven high when the CP2102/9 enters the USB suspend state. |+| 13 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 14 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 15 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 16 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 17 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 18 | NC | unconnected | Unused on the CP2102 - leave unconnected or tie to VDD. (On the pin-compatible CP2109, this pin is VPP, the EPROM programming supply; a 4.7 µF cap to GND maintains board compatibility.) |+| 19 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 20 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 21 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 22 | NC | unconnected | No connect. Leave unconnected or tie to VDD. |+| 23 | CTS | input | Clear To Send control input (active low). RS-232 handshake input; can be left unconnected when not used. |+| 24 | RTS | output | Request To Send control output (active low). RS-232 handshake output; can be left unconnected when not used. |+| 25 | RXD | input | Asynchronous UART receive data input. |+| 26 | TXD | output | Asynchronous UART transmit data output. Baud rates from 300 bps up to 921600 bps (1 Mbps peak). |+| 27 | DSR | input | Data Set Ready control input (active low). RS-232 modem control input; can be left unconnected when not used. |+| 28 | DTR | output | Data Terminal Ready control output (active low). RS-232 modem control output; can be left unconnected when not used. |++## Key specifications++| Parameter | Value |+|---|---|+| Type | USB 2.0-to-UART bridge |+| USB | full-speed (virtual COM port) |+| Max UART rate | 1 Mbps |+| Integrated | USB PHY + regulator + clock + 1 KB EEPROM |+| Modem control | RTS/CTS/DSR/DTR/DCD/RI |+| External parts | 2 capacitors |+| Supply voltage | USB 5 V or 3.3 V |+| Package | QFN-28 (5x5 mm) |++## Ordering variants++- `CP2102-GMR (QFN-28)`+- `CP2102-GM (QFN-28)`++## CAD (KiCad official)++- Symbol: `CP2102 (generated from datasheet; KiCad has only CP2102N)`+- Footprint: `Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm`+- 3D model: QFN-28 (KiCad packages3D)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Silicon Labs datasheet](https://www.silabs.com/documents/public/data-sheets/CP2102-9.pdf) (26 pp, sha256 `f025d9c738e49065`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/cp2102-datasheet.pdf)
cp2102.glbadded⋯ 1 unchanged line ⋯
cp2102.kicad_modadded+571@@ -0,0 +1,571 @@+(footprint "QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm"+ (version 20260206)+ (generator "kicad-footprint-generator")+ (layer "F.Cu")+ (descr "QFN, 28 Pin (http://ww1.microchip.com/downloads/en/PackagingSpec/00000049BQ.pdf#page=283)")+ (tags "QFN NoLead")+ (property "Reference" "REF**"+ (at 0 -3.8 0)+ (layer "F.SilkS")+ (effects+ (font+ (size 1 1)+ (thickness 0.15)+ )+ )+ )+ (property "Value" "QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm"+ (at 0 3.8 0)+ (layer "F.Fab")+ (effects+ (font+ (size 1 1)+ (thickness 0.15)+ )+ )+ )+ (property "KiLib_Generator" "package/no_lead"+ (at 0 0 0)+ (layer "F.SilkS")+ (hide yes)+ (effects+ (font+ (size 1 1)+ (thickness 0.15)+ )+ )+ )+ (attr smd)+ (duplicate_pad_numbers_are_jumpers no)+ (fp_line+ (start -2.61 -2.61)+ (end -1.885 -2.61)+ (stroke+ (width 0.12)+ (type solid)+ )+ (layer "F.SilkS")+ )+ (fp_line+ (start -2.61 -1.885)+ (end -2.61 -2.61)+ (stroke+ (width 0.12)+ (type solid)+ )+ (layer "F.SilkS")+ )+ (fp_line+ (start -2.61 2.61)+ (end -2.61 1.885)+ (stroke+ (width 0.12)+ (type solid)+ )+ (layer "F.SilkS")+ )+ (fp_line+ (start -1.885 2.61)+ (end -2.61 2.61)+ (stroke+ (width 0.12)+ (type solid)+ )+ (layer "F.SilkS")+ )+ (fp_line+ (start 1.885 -2.61)+ (end 2.61 -2.61)+ (stroke+ (width 0.12)+ (type solid)+ )+ (layer "F.SilkS")+ )+ (fp_line+ (start 2.61 -2.61)+ (end 2.61 -1.885)+ (stroke+ (width 0.12)+ (type solid)+ )+ (layer "F.SilkS")+ )+ (fp_line+ (start 2.61 1.885)+ (end 2.61 2.61)+ (stroke+ (width 0.12)+ (type solid)+ )+ (layer "F.SilkS")+ )+ (fp_line+ (start 2.61 2.61)+ (end 1.885 2.61)+ (stroke+ (width 0.12)+ (type solid)+ )+ (layer "F.SilkS")+ )+ (fp_poly+ (pts+ (xy -3.11 -1.5)+ (xy -3.44 -1.26)+ (xy -3.44 -1.74)+ )+ (stroke+ (width 0.12)+ (type solid)+ )+ (fill yes)+ (layer "F.SilkS")+ )+ (fp_line+ (start -3.1 -1.88)+ (end -2.75 -1.88)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start -3.1 1.88)+ (end -3.1 -1.88)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start -2.75 -2.75)+ (end -1.88 -2.75)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start -2.75 -1.88)+ (end -2.75 -2.75)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start -2.75 1.88)+ (end -3.1 1.88)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start -2.75 2.75)+ (end -2.75 1.88)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start -1.88 -3.1)+ (end 1.88 -3.1)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start -1.88 -2.75)+ (end -1.88 -3.1)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start -1.88 2.75)+ (end -2.75 2.75)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start -1.88 3.1)+ (end -1.88 2.75)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 1.88 -3.1)+ (end 1.88 -2.75)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 1.88 -2.75)+ (end 2.75 -2.75)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 1.88 2.75)+ (end 1.88 3.1)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 1.88 3.1)+ (end -1.88 3.1)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 2.75 -2.75)+ (end 2.75 -1.88)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 2.75 -1.88)+ (end 3.1 -1.88)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 2.75 1.88)+ (end 2.75 2.75)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 2.75 2.75)+ (end 1.88 2.75)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 3.1 -1.88)+ (end 3.1 1.88)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_line+ (start 3.1 1.88)+ (end 2.75 1.88)+ (stroke+ (width 0.05)+ (type solid)+ )+ (layer "F.CrtYd")+ )+ (fp_poly+ (pts+ (xy -1.5 -2.5)+ (xy 2.5 -2.5)+ (xy 2.5 2.5)+ (xy -2.5 2.5)+ (xy -2.5 -1.5)+ )+ (stroke+ (width 0.1)+ (type solid)+ )+ (fill no)+ (layer "F.Fab")+ )+ (fp_text user "${REFERENCE}"+ (at 0 0 0)+ (layer "F.Fab")+ (effects+ (font+ (size 1 1)+ (thickness 0.15)+ )+ )+ )+ (pad "" smd roundrect+ (at -1.12 -1.12)+ (size 0.9 0.9)+ (layers "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "" smd roundrect+ (at -1.12 0)+ (size 0.9 0.9)+ (layers "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "" smd roundrect+ (at -1.12 1.12)+ (size 0.9 0.9)+ (layers "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "" smd roundrect+ (at 0 -1.12)+ (size 0.9 0.9)+ (layers "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "" smd roundrect+ (at 0 0)+ (size 0.9 0.9)+ (layers "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "" smd roundrect+ (at 0 1.12)+ (size 0.9 0.9)+ (layers "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "" smd roundrect+ (at 1.12 -1.12)+ (size 0.9 0.9)+ (layers "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "" smd roundrect+ (at 1.12 0)+ (size 0.9 0.9)+ (layers "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "" smd roundrect+ (at 1.12 1.12)+ (size 0.9 0.9)+ (layers "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "1" smd roundrect+ (at -2.45 -1.5)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "2" smd roundrect+ (at -2.45 -1)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "3" smd roundrect+ (at -2.45 -0.5)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "4" smd roundrect+ (at -2.45 0)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "5" smd roundrect+ (at -2.45 0.5)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "6" smd roundrect+ (at -2.45 1)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "7" smd roundrect+ (at -2.45 1.5)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "8" smd roundrect+ (at -1.5 2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "9" smd roundrect+ (at -1 2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "10" smd roundrect+ (at -0.5 2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "11" smd roundrect+ (at 0 2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "12" smd roundrect+ (at 0.5 2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "13" smd roundrect+ (at 1 2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "14" smd roundrect+ (at 1.5 2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "15" smd roundrect+ (at 2.45 1.5)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "16" smd roundrect+ (at 2.45 1)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "17" smd roundrect+ (at 2.45 0.5)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "18" smd roundrect+ (at 2.45 0)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "19" smd roundrect+ (at 2.45 -0.5)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "20" smd roundrect+ (at 2.45 -1)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "21" smd roundrect+ (at 2.45 -1.5)+ (size 0.8 0.25)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "22" smd roundrect+ (at 1.5 -2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "23" smd roundrect+ (at 1 -2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "24" smd roundrect+ (at 0.5 -2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "25" smd roundrect+ (at 0 -2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "26" smd roundrect+ (at -0.5 -2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "27" smd roundrect+ (at -1 -2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "28" smd roundrect+ (at -1.5 -2.45)+ (size 0.25 0.8)+ (layers "F.Cu" "F.Mask" "F.Paste")+ (roundrect_rratio 0.25)+ )+ (pad "29" smd rect+ (at 0 0)+ (size 3.35 3.35)+ (property pad_prop_heatsink)+ (layers "F.Cu" "F.Mask")+ (zone_connect 2)+ )+ (embedded_fonts no)+ (model "${KICAD10_3DMODEL_DIR}/Package_DFN_QFN.3dshapes/QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm.step"+ (offset+ (xyz 0 0 0)+ )+ (scale+ (xyz 1 1 1)+ )+ (rotate+ (xyz 0 0 0)+ )+ )+)
cp2102.kicad_symadded+125@@ -0,0 +1,125 @@+(kicad_symbol_lib (version 20211014) (generator ds2sf_rect)+ (symbol "CP2102" (in_bom yes) (on_board yes)+ (property "Reference" "U" (at 0 20.32 0) (effects (font (size 1.27 1.27))))+ (property "Value" "CP2102" (at 0 -22.86 0) (effects (font (size 1.27 1.27))))+ (property "Footprint" "" (at 0 0 0) (effects (font (size 1.27 1.27)) hide))+ (symbol "CP2102_0_1"+ (rectangle (start -12.70 17.78) (end 12.70 -20.32)+ (stroke (width 0.254) (type default)) (fill (type background)))+ )+ (symbol "CP2102_1_1"+ (pin input line (at -17.78 15.24 0) (length 5.08)+ (name "DCD" (effects (font (size 1.27 1.27))))+ (number "1" (effects (font (size 1.27 1.27))))+ )+ (pin input line (at -17.78 12.70 0) (length 5.08)+ (name "RI" (effects (font (size 1.27 1.27))))+ (number "2" (effects (font (size 1.27 1.27))))+ )+ (pin power_in line (at -17.78 10.16 0) (length 5.08)+ (name "GND" (effects (font (size 1.27 1.27))))+ (number "3" (effects (font (size 1.27 1.27))))+ )+ (pin bidirectional line (at -17.78 7.62 0) (length 5.08)+ (name "D+" (effects (font (size 1.27 1.27))))+ (number "4" (effects (font (size 1.27 1.27))))+ )+ (pin bidirectional line (at -17.78 5.08 0) (length 5.08)+ (name "D-" (effects (font (size 1.27 1.27))))+ (number "5" (effects (font (size 1.27 1.27))))+ )+ (pin power_in line (at -17.78 2.54 0) (length 5.08)+ (name "VDD" (effects (font (size 1.27 1.27))))+ (number "6" (effects (font (size 1.27 1.27))))+ )+ (pin power_in line (at -17.78 0.00 0) (length 5.08)+ (name "REGIN" (effects (font (size 1.27 1.27))))+ (number "7" (effects (font (size 1.27 1.27))))+ )+ (pin input line (at -17.78 -2.54 0) (length 5.08)+ (name "VBUS" (effects (font (size 1.27 1.27))))+ (number "8" (effects (font (size 1.27 1.27))))+ )+ (pin bidirectional line (at -17.78 -5.08 0) (length 5.08)+ (name "RST" (effects (font (size 1.27 1.27))))+ (number "9" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at -17.78 -7.62 0) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "10" (effects (font (size 1.27 1.27))))+ )+ (pin output line (at -17.78 -10.16 0) (length 5.08)+ (name "SUSPEND" (effects (font (size 1.27 1.27))))+ (number "11" (effects (font (size 1.27 1.27))))+ )+ (pin output line (at -17.78 -12.70 0) (length 5.08)+ (name "SUSPEND" (effects (font (size 1.27 1.27))))+ (number "12" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at -17.78 -15.24 0) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "13" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at -17.78 -17.78 0) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "14" (effects (font (size 1.27 1.27))))+ )+ (pin output line (at 17.78 15.24 180) (length 5.08)+ (name "DTR" (effects (font (size 1.27 1.27))))+ (number "28" (effects (font (size 1.27 1.27))))+ )+ (pin input line (at 17.78 12.70 180) (length 5.08)+ (name "DSR" (effects (font (size 1.27 1.27))))+ (number "27" (effects (font (size 1.27 1.27))))+ )+ (pin output line (at 17.78 10.16 180) (length 5.08)+ (name "TXD" (effects (font (size 1.27 1.27))))+ (number "26" (effects (font (size 1.27 1.27))))+ )+ (pin input line (at 17.78 7.62 180) (length 5.08)+ (name "RXD" (effects (font (size 1.27 1.27))))+ (number "25" (effects (font (size 1.27 1.27))))+ )+ (pin output line (at 17.78 5.08 180) (length 5.08)+ (name "RTS" (effects (font (size 1.27 1.27))))+ (number "24" (effects (font (size 1.27 1.27))))+ )+ (pin input line (at 17.78 2.54 180) (length 5.08)+ (name "CTS" (effects (font (size 1.27 1.27))))+ (number "23" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at 17.78 0.00 180) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "22" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at 17.78 -2.54 180) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "21" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at 17.78 -5.08 180) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "20" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at 17.78 -7.62 180) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "19" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at 17.78 -10.16 180) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "18" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at 17.78 -12.70 180) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "17" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at 17.78 -15.24 180) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "16" (effects (font (size 1.27 1.27))))+ )+ (pin no_connect line (at 17.78 -17.78 180) (length 5.08)+ (name "NC" (effects (font (size 1.27 1.27))))+ (number "15" (effects (font (size 1.27 1.27))))+ )+ )+ )+)
docs/cp2102-datasheet.pdfadded⋯ 1 unchanged line ⋯
docs/hero.pngadded⋯ 1 unchanged line ⋯
package.jsonadded+31@@ -0,0 +1,31 @@+{+ "slug": "cp2102",+ "version": "0.1.0",+ "type": "component",+ "description": "Silicon Labs single-chip USB-to-UART bridge, QFN-28. Integrated USB, regulator, clock, EEPROM. Up to 1 Mbps. Datasheet-verified.",+ "tags": [+ "component",+ "interface",+ "usb-uart",+ "usb-bridge",+ "virtual-com-port",+ "qfn-28",+ "silicon-labs"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "cp2102.kicad_sym",+ "cp2102.kicad_mod",+ "cp2102.glb",+ "docs/hero.png",+ "docs/cp2102-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ]+}
page.json+28−7@@ -4,8 +4,16 @@ "slug": "cp2102", "title": "CP2102", "brief": "USB to UART bridge, up to 1Mbps, QFN-28",- "version": "1.0.0",- "tags": [],+ "version": "0.1.0",+ "tags": [+ "component",+ "interface",+ "usb-uart",+ "usb-bridge",+ "virtual-com-port",+ "qfn-28",+ "silicon-labs"+ ], "license": "MIT", "component": { "mpn": "CP2102",@@ -20,18 +28,31 @@ }, "readme": "# CP2102\n\nUSB to UART bridge, up to 1Mbps, QFN-28\n\nThe CP2102 is a USB to UART bridge controller from Silicon Labs. Supports baud rates up to 1Mbps with integrated USB transceiver and clock. Widely used in development boards and serial adapters.", "author": {- "id": "695820315b5f1e4db2fcf602", "name": "Kyle Bergstedt", "email": "[email protected]" },- "visibility": {- "public": true+ "visibility": "public",+ "hero": {+ "type": "image",+ "path": "docs/hero.png" },- "hero": null, "sample_prompts": [], "discovery_triggers": [], "discovery_pitch": null, "metadata": {}, "created_at": "2026-05-28T05:33:24.464Z",- "updated_at": "2026-05-28T05:33:24.464Z"+ "updated_at": "2026-05-28T05:33:24.464Z",+ "description": "Silicon Labs single-chip USB-to-UART bridge, QFN-28. Integrated USB, regulator, clock, EEPROM. Up to 1 Mbps. Datasheet-verified.",+ "dependencies": {},+ "files": [+ "page.json",+ "README.md",+ "cp2102.kicad_sym",+ "cp2102.kicad_mod",+ "cp2102.glb",+ "docs/hero.png",+ "docs/cp2102-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ] }