← Commit history
README.md+32−8
@@ -1,8 +1,10 @@ # ZD1117ILTR50 -**Zetta** · Linear Voltage Regulators (LDO) · SOT-223-4+> Zetta's datasheet does not state the tab connection; this land follows the 1117-family convention (tab = Vout). Check before use. -ZD1117ILTR50 from Zetta, in a SOT-223-4. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.+**Zetta** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-223-4++ZD1117ILTR50 from Zetta, in a SOT-223-4. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.  ## Pinout @@ -11,7 +13,6 @@ ZD1117ILTR50 from Zetta, in a SOT-223-4. Pinout and pin descriptions extracted f | 1 | Vss/ADJ | power_in | Ground pin on the fixed-output versions such as the 5.0V ZD1117ILTR50, and the adjust pin on the ZD1117-ADJ version. | | 2 | Vout | power_out | Regulated output voltage, 5.0V (4.9V to 5.1V at 0 to 1A) for the ZD1117-5.0V, with a recommended 10uF tantalum output capacitor. | | 3 | Vin | power_in | Supply voltage input with a maximum of 18V absolute and 16V recommended, bypassed with a recommended 10uF tantalum capacitor. |-| 4 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |  ## Key specifications @@ -19,13 +20,36 @@ ZD1117ILTR50 from Zetta, in a SOT-223-4. Pinout and pin descriptions extracted f |---|---| | Manufacturer | Zetta | | Package | SOT-223-4 |-| Category | Power Supply Chip |-| Pins | 4 |+| Category | Power Management (PMIC) |+| Pins | 3 |++## Electrical characteristics++Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).++| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |+|---|---|---|---|---|---|---|---|+| Output Voltage (ZD1117-5.0V) | Vout | 4.9 | 5 | 5.1 | V | 0≤Iout≤1A, Vin=7.0V | 4 |+| Line Regulation (ZD1117-5.0V) | ΔVout |  | 0.1 | 0.2 | %/V | Iout=10mA, 6.5V≤Vin≤16V | 4 |+| Load Regulation (ZD1117-5.0V) | ΔVout |  | 10 | 30 | mV | Vin=6.5V,10mA≤Iout≤1A | 4 |+| Dropout Voltage | Vdrop |  | 1.23 | 1.3 | V | Iout=100mA | 5 |+| Dropout Voltage | Vdrop |  | 1.3 | 1.5 | V | Iout=1A | 5 |+| Current Limit | Ilimit |  | 1 |  | A | Vin-Vout=2V, Tj=25°C | 5 |+| Quiescent Current (ZD1117-5.0V) | Iq |  | 2 | 5 | mA | ZD1117-5.0V, Vin =12V | 5 |+| Temperature Coefficient | ΔV/ΔT | -100 |  | 100 | ppm |  | 5 |+| Thermal Resistance Junction-to-Case, SOT-223 | JC |  | 20 |  | °C/W | SOT-223 | 5 |+| Max Input Voltage | Vin |  |  | 18 | V |  | 3 |+| Max Operating Junction Temperature | Tj |  |  | 150 | °C |  | 3 |+| Ambient Temperature | Ta | -40 |  | 85 | °C |  | 3 |+| Storage Temperature | Ts | -40 |  | 150 | °C |  | 3 |+| Lead Temperature |  |  |  | 260 | °C | 10 s | 3 |+| Input Voltage Range | Vin |  |  | 16 | V |  | 3 |+| Operating Junction Temperature | Tj | -40 |  | 125 | °C |  | 3 |  ## CAD (KiCad official)  - Symbol: `ZD1117ILTR50`-- Footprint: `Package_TO_SOT_SMD:SOT-223`+- Footprint: `Package_TO_SOT_SMD:SOT-223-3_TabPin2` - 3D model: SOT-223-4 (KiCad packages3D, STEP) - 3D model files: `zd1117iltr50-etched.step` / `zd1117iltr50-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `zd1117iltr50.step` / `zd1117iltr50.glb` are the bare package body. @@ -33,8 +57,8 @@ ZD1117ILTR50 from Zetta, in a SOT-223-4. Pinout and pin descriptions extracted f  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Zetta datasheet](docs/zd1117iltr50-datasheet.pdf) (9 pp, sha256 `69324c98cfc0544d`, retrieved 2026-11-10, tier: lcsc)-- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **Datasheet:** [Zetta datasheet](docs/zd1117iltr50-datasheet.pdf) (9 pp, sha256 `69324c98cfc0544d`, retrieved 2026-11-13, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - **CAD:** KiCad official libraries (CC-BY-SA 4.0).  [Datasheet PDF](docs/zd1117iltr50-datasheet.pdf)
docs/hero.png
⋯ 1 unchanged line ⋯
package.json+17−40
@@ -1,11 +1,11 @@ {   "slug": "zd1117iltr50",-  "version": "0.1.0",+  "version": "0.2.0",   "type": "component",-  "description": "Zetta Linear Voltage Regulators (LDO), SOT-223-4. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "description": "Zetta Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, SOT-223-4. Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.",   "tags": [     "component",-    "power supply chip",+    "power management (pmic)",     "zd1117iltr50",     "factory-2.0.0",     "extractor-text"@@ -28,22 +28,22 @@     "viewers/symbol.html",     "viewers/footprint.html",     "zd1117iltr50-hero.glb",-    "zd1117iltr50-hero.overlay.json",-    "zd1117iltr50-etched.glb"+    "zd1117iltr50-hero.overlay.json"   ],   "component": {     "mpn": "ZD1117ILTR50",+    "build_note": "Zetta's datasheet does not state the tab connection; this land follows the 1117-family convention (tab = Vout). Check before use",     "manufacturer": "Zetta",     "package": "SOT-223-4",-    "pin_count": 4,-    "category": "Power Supply Chip",-    "subcategory": "Linear Voltage Regulators (LDO)",+    "pin_count": 3,+    "category": "Power Management (PMIC)",+    "subcategory": "Voltage Regulators - Linear, Low Drop Out (LDO) Regulators",     "datasheet": "https://datasheet.lcsc.com/datasheet/pdf/483708bcf5a5f52f4ebdf78449cd1264.pdf",     "parts": {       "symbol": "zd1117iltr50.kicad_sym",       "footprint": "zd1117iltr50.kicad_mod",       "model_3d": "zd1117iltr50-hero.glb",-      "model_3d_plain": "zd1117iltr50-etched.glb",+      "model_3d_plain": "zd1117iltr50.glb",       "model_3d_step": "zd1117iltr50-etched.step",       "model_3d_step_plain": "zd1117iltr50.step",       "lbr": "zd1117iltr50.lbr"@@ -52,7 +52,7 @@       "lcsc": "C2928931"     },     "distributor_check": {-      "checked_at": "2026-11-10T03:39:11Z",+      "checked_at": "2026-11-13T02:02:33Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": null,@@ -81,43 +81,20 @@         "name": "Vin",         "type": "power_in",         "description": "Supply voltage input with a maximum of 18V absolute and 16V recommended, bypassed with a recommended 10uF tantalum capacitor."-      },-      {-        "number": "4",-        "name": "EP",-        "type": "passive",-        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."       }     ],     "provenance": {-      "extractor": "extract_pins 0.3",-      "factory_chain": {-        "factory": "2.0.0",-        "extractor": "extract_pins 0.3",-        "primary_model": "claude-sonnet-5-5",-        "primary_mode": "text+vision",-        "consensus_model": "claude-opus-5-5",-        "consensus": "agreed",-        "guards": "pin_guards 0.1: passed",-        "guard_notes": [-          "extractor flagged: The package hint is SOT-223-4, but the datasheet pin table for SOT-223 (page 2) numbers only three p; Pin 1 is labeled 'Vss/ADJ', described as 'Ground Pin/Adjustable'. For the ordered fixed 5.0V part (s",-          "exposed pad 4 added from the footprint",-          "vision extraction: provenance cannot be text-verified; needs consensus"-        ],-        "pages_sent": 9,-        "cost_usd": 0.043,-        "at": "2026-11-10T03:38:55"-      },+      "extractor": "ds2sf",       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/483708bcf5a5f52f4ebdf78449cd1264.pdf",         "pages": 9,         "sha256": "69324c98cfc0544d",-        "source_tier": "lcsc"+        "source_tier": "mfr"       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {-        "total": 4,-        "described": 4,+        "total": 3,+        "described": 3,         "cites_pages": true,         "refuses_to_fabricate": true       }@@ -143,7 +120,7 @@         "centre_offset_mm": 0.0,         "footprint_binding": "identity",         "sha256": "77ad6dbacc493cb619c728f26d2ddcf461eb0feb6b977b47d01d51e67016f654",-        "checked": "2026-11-10",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -161,8 +138,8 @@         "zmin_mm": -0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "bc56e32da45357dae9c0be2df81a4999b350c931b6e6c32a00593807df2f9cba",-        "checked": "2026-11-10",+        "sha256": "97e44449af1333b26f914332a438401d79fea8fbf50c097da419ca3f1ce933f2",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]
page.json+19−42
@@ -4,28 +4,29 @@   "slug": "zd1117iltr50",   "title": "ZD1117ILTR50",   "brief": "Zetta Linear Voltage Regulators (LDO), SOT-223-4. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.2.0",   "license": "CC-BY-SA-4.0",   "tags": [     "component",-    "power supply chip",+    "power management (pmic)",     "zd1117iltr50",     "factory-2.0.0",     "extractor-text"   ],   "component": {     "mpn": "ZD1117ILTR50",+    "build_note": "Zetta's datasheet does not state the tab connection; this land follows the 1117-family convention (tab = Vout). Check before use",     "manufacturer": "Zetta",     "package": "SOT-223-4",-    "pin_count": 4,-    "category": "Power Supply Chip",-    "subcategory": "Linear Voltage Regulators (LDO)",+    "pin_count": 3,+    "category": "Power Management (PMIC)",+    "subcategory": "Voltage Regulators - Linear, Low Drop Out (LDO) Regulators",     "datasheet": "https://datasheet.lcsc.com/datasheet/pdf/483708bcf5a5f52f4ebdf78449cd1264.pdf",     "parts": {       "symbol": "zd1117iltr50.kicad_sym",       "footprint": "zd1117iltr50.kicad_mod",       "model_3d": "zd1117iltr50-hero.glb",-      "model_3d_plain": "zd1117iltr50-etched.glb",+      "model_3d_plain": "zd1117iltr50.glb",       "model_3d_step": "zd1117iltr50-etched.step",       "model_3d_step_plain": "zd1117iltr50.step",       "lbr": "zd1117iltr50.lbr"@@ -34,7 +35,7 @@       "lcsc": "C2928931"     },     "distributor_check": {-      "checked_at": "2026-11-10T03:39:11Z",+      "checked_at": "2026-11-13T02:02:33Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": null,@@ -63,43 +64,20 @@         "name": "Vin",         "type": "power_in",         "description": "Supply voltage input with a maximum of 18V absolute and 16V recommended, bypassed with a recommended 10uF tantalum capacitor."-      },-      {-        "number": "4",-        "name": "EP",-        "type": "passive",-        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."       }     ],     "provenance": {-      "extractor": "extract_pins 0.3",-      "factory_chain": {-        "factory": "2.0.0",-        "extractor": "extract_pins 0.3",-        "primary_model": "claude-sonnet-5-5",-        "primary_mode": "text+vision",-        "consensus_model": "claude-opus-5-5",-        "consensus": "agreed",-        "guards": "pin_guards 0.1: passed",-        "guard_notes": [-          "extractor flagged: The package hint is SOT-223-4, but the datasheet pin table for SOT-223 (page 2) numbers only three p; Pin 1 is labeled 'Vss/ADJ', described as 'Ground Pin/Adjustable'. For the ordered fixed 5.0V part (s",-          "exposed pad 4 added from the footprint",-          "vision extraction: provenance cannot be text-verified; needs consensus"-        ],-        "pages_sent": 9,-        "cost_usd": 0.043,-        "at": "2026-11-10T03:38:55"-      },+      "extractor": "ds2sf",       "datasheet": {         "url": "https://datasheet.lcsc.com/datasheet/pdf/483708bcf5a5f52f4ebdf78449cd1264.pdf",         "pages": 9,         "sha256": "69324c98cfc0544d",-        "source_tier": "lcsc"+        "source_tier": "mfr"       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {-        "total": 4,-        "described": 4,+        "total": 3,+        "described": 3,         "cites_pages": true,         "refuses_to_fabricate": true       }@@ -125,7 +103,7 @@         "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "77ad6dbacc493cb619c728f26d2ddcf461eb0feb6b977b47d01d51e67016f654",-        "checked": "2026-11-10",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -143,8 +121,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "bc56e32da45357dae9c0be2df81a4999b350c931b6e6c32a00593807df2f9cba",-        "checked": "2026-11-10",+        "sha256": "97e44449af1333b26f914332a438401d79fea8fbf50c097da419ca3f1ce933f2",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]@@ -191,10 +169,9 @@     "viewers/symbol.html",     "viewers/footprint.html",     "zd1117iltr50-hero.glb",-    "zd1117iltr50-hero.overlay.json",-    "zd1117iltr50-etched.glb"+    "zd1117iltr50-hero.overlay.json"   ],-  "visibility": {-    "public": true-  }+  "visibility": "public",+  "description": "Zetta Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, SOT-223-4. Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file
zd1117iltr50-hero.glb
⋯ 1 unchanged line ⋯
zd1117iltr50-hero.overlay.json+164−168
@@ -1,172 +1,168 @@ {-  "spec": "adom-hero 1.4",-  "mpn": "ZD1117ILTR50",-  "kind": "component + footprint reference art",-  "board_use": false,-  "plane_z_mm": -0.02,-  "units": "metre",-  "upAxis": "Z",-  "layers": {-    "pad_outlines": {-      "material": "Footprint pads - teal dashed outlines - 50 percent opacity",-      "rgba": [-        0.0,-        0.902,-        0.863,-        0.5-      ],-      "pads": 4,-      "span_mm": 8.4,-      "dash_mm": 0.21,-      "gap_mm": 0.126,-      "pad_stroke_mm": 0.0504-    },-    "silkscreen": {-      "material": "Silkscreen reference lines - 30 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.3-      ],-      "footprint_items": 5,-      "pin1": {-        "source": "footprint silkscreen",-        "pad": "1"-      }-    },-    "signal_names": {-      "material": "Signal names - 50 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.5-      ],-      "font": "DejaVu Sans Mono",-      "labels": 4,-      "sides": "top + mirrored underside (single-sided)",-      "fallback_to_pad_number": 0-    }+ "spec": "adom-hero 1.4",+ "mpn": "ZD1117ILTR50",+ "kind": "component + footprint reference art",+ "board_use": false,+ "plane_z_mm": -0.02,+ "units": "metre",+ "upAxis": "Z",+ "layers": {+  "pad_outlines": {+   "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+   "rgba": [+    0.0,+    0.902,+    0.863,+    0.5+   ],+   "pads": 4,+   "span_mm": 8.4,+   "dash_mm": 0.21,+   "gap_mm": 0.126,+   "pad_stroke_mm": 0.0504   },-  "align": {-    "ok": true,-    "centre_offset_mm": 0.0,-    "tolerance_mm": 0.664,-    "orientation_flipped": false,-    "contacts_bbox_mm": [-      -3.5,-      3.5,-      -2.684,-      2.684-    ],-    "pads_bbox_mm": [-      -4.15,-      4.15,-      -3.05,-      3.05-    ],-    "seating_z_mm": 0.0+  "silkscreen": {+   "material": "Silkscreen reference lines - 30 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.3+   ],+   "footprint_items": 5,+   "pin1": {+    "source": "footprint silkscreen",+    "pad": "1"+   }   },-  "sources": {-    "glb": "zd1117iltr50-etched.glb",-    "glb_sha256": "95da9b5b0fd01f1ee62dd553071f991c2d8cc089847497566dca3c5776c0d1d1",-    "footprint": "zd1117iltr50.kicad_mod",-    "footprint_sha256": "4c832c82814b3e769970f3738bb3d2f73db768b42c5c7cae38d390739cc249fc",-    "pins": "page.json component.pins",-    "pins_sha256": "8ef2a942d53096cfb1a646417f54381991fc5769bb7d7b1fcd576d0d25ac0f95"-  },-  "generator": "adom-wiki 1.8.15 (component_hero)",-  "labels": [-    {-      "pad": "1",-      "text": "Vss/ADJ",-      "x": -4.3,-      "y": -2.3,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "2",-      "text": "Vout",-      "x": -4.3,-      "y": 0.0,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "3",-      "text": "Vin",-      "x": -4.3,-      "y": 2.3,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "4",-      "text": "EP",-      "x": 4.3,-      "y": 0.0,-      "align": "left",-      "vertical": false,-      "h": 0.6-    }+  "signal_names": {+   "material": "Signal names - 50 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.5+   ],+   "font": "DejaVu Sans Mono",+   "labels": 3,+   "sides": "top + mirrored underside (single-sided)",+   "omitted": null,+   "fallback_to_pad_number": 0+  }+ },+ "align": {+  "ok": true,+  "board_underside": false,+  "electrical_pads_without_contact": [],+  "mounting_pads_left_out": [],+  "centre_offset_mm": 0.0,+  "over_pads": true,+  "tolerance_mm": 0.664,+  "orientation_flipped": false,+  "contacts_bbox_mm": [+   -3.5,+   3.5,+   -2.684,+   2.684+  ],+  "pads_bbox_mm": [+   -4.15,+   4.15,+   -3.05,+   3.05   ],-  "pads": [-    {-      "number": "1",-      "shape": "roundrect",-      "center_mm": [-        -3.15,-        -2.3-      ],-      "size_mm": [-        2.0,-        1.5-      ],-      "rot": 0.0-    },-    {-      "number": "2",-      "shape": "roundrect",-      "center_mm": [-        -3.15,-        0.0-      ],-      "size_mm": [-        2.0,-        1.5-      ],-      "rot": 0.0-    },-    {-      "number": "3",-      "shape": "roundrect",-      "center_mm": [-        -3.15,-        2.3-      ],-      "size_mm": [-        2.0,-        1.5-      ],-      "rot": 0.0-    },-    {-      "number": "4",-      "shape": "roundrect",-      "center_mm": [-        3.15,-        0.0-      ],-      "size_mm": [-        2.0,-        3.8-      ],-      "rot": 0.0-    }-  ]-}+  "seating_z_mm": 0.0+ },+ "sources": {+  "glb": "zd1117iltr50-etched.glb",+  "glb_sha256": "95da9b5b0fd01f1ee62dd553071f991c2d8cc089847497566dca3c5776c0d1d1",+  "footprint": "zd1117iltr50.kicad_mod",+  "footprint_sha256": "5f6cad94d6c821d01d360a4a09cca4b89e63ae0ce12c33d1dd0ba4e30e86c523",+  "pins": "page.json component.pins",+  "pins_sha256": "ea1383d85013658ddafd6fb766b4b96efba10038b0afbe8beac29dd24f55f78c"+ },+ "generator": "factory/hero_glb.py",+ "labels": [+  {+   "pad": "1",+   "text": "Vss/ADJ",+   "x": -4.3,+   "y": -2.3,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "2",+   "text": "Vout",+   "x": -4.3,+   "y": 0.0,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "3",+   "text": "Vin",+   "x": -4.3,+   "y": 2.3,+   "align": "right",+   "vertical": false,+   "h": 0.6+  }+ ],+ "pads": [+  {+   "number": "1",+   "shape": "roundrect",+   "center_mm": [+    -3.15,+    -2.3+   ],+   "size_mm": [+    2.0,+    1.5+   ],+   "rot": 0.0+  },+  {+   "number": "2",+   "shape": "roundrect",+   "center_mm": [+    -3.15,+    0.0+   ],+   "size_mm": [+    2.0,+    1.5+   ],+   "rot": 0.0+  },+  {+   "number": "2",+   "shape": "roundrect",+   "center_mm": [+    3.15,+    0.0+   ],+   "size_mm": [+    2.0,+    3.8+   ],+   "rot": 0.0+  },+  {+   "number": "3",+   "shape": "roundrect",+   "center_mm": [+    -3.15,+    2.3+   ],+   "size_mm": [+    2.0,+    1.5+   ],+   "rot": 0.0+  }+ ]+}\ No newline at end of file
zd1117iltr50.kicad_mod+32−32
@@ -1,4 +1,4 @@-(footprint "SOT-223"+(footprint "SOT-223-3_TabPin2" 	(version 20260206) 	(generator "pcbnew") 	(generator_version "10.0")@@ -8,7 +8,7 @@ 	(property "Reference" "REF**" 		(at 0 -4.5 0) 		(layer "F.SilkS")-		(uuid "4497a1e1-94b1-4cba-abfc-02d82a04371f")+		(uuid "095b50a5-76ce-476b-aa10-37a37fa441f1") 		(effects 			(font 				(size 1 1)@@ -16,10 +16,10 @@ 			) 		) 	)-	(property "Value" "SOT-223"+	(property "Value" "SOT-223-3_TabPin2" 		(at 0 4.5 0) 		(layer "F.Fab")-		(uuid "222a057b-4f1f-481e-81c0-82276f6e2fbf")+		(uuid "a763838d-1dc3-4eda-bbc0-fbcf1edf1449") 		(effects 			(font 				(size 1 1)@@ -27,12 +27,12 @@ 			) 		) 	)-	(property "Datasheet" "https://datasheet.lcsc.com/datasheet/pdf/483708bcf5a5f52f4ebdf78449cd1264.pdf"+	(property "Datasheet" "" 		(at 0 0 0) 		(unlocked yes) 		(layer "F.Fab") 		(hide yes)-		(uuid "cf35375b-a35a-4ccf-b401-52356d4eb3ab")+		(uuid "0fecb949-4744-4c65-8091-70f595847ba4") 		(effects 			(font 				(size 1.27 1.27)@@ -45,7 +45,7 @@ 		(unlocked yes) 		(layer "F.Fab") 		(hide yes)-		(uuid "e0b857b7-85f4-442e-9375-43b7f0b65024")+		(uuid "7dd6192e-e612-428f-816e-6f28697542d5") 		(effects 			(font 				(size 1.27 1.27)@@ -63,7 +63,7 @@ 			(type solid) 		) 		(layer "F.SilkS")-		(uuid "10341b74-de1d-44f8-b919-9dc7b01c77a6")+		(uuid "e98ec803-a6f4-4196-9fa0-d9f7619efa9d") 	) 	(fp_line 		(start -1.85 3.41)@@ -73,7 +73,7 @@ 			(type solid) 		) 		(layer "F.SilkS")-		(uuid "9eaaee9c-d787-4c4e-9409-486f5d803253")+		(uuid "6e43f798-7915-403c-b947-4851bde35045") 	) 	(fp_line 		(start 1.91 -3.41)@@ -83,7 +83,7 @@ 			(type solid) 		) 		(layer "F.SilkS")-		(uuid "668bbda1-c7e1-4e23-9d62-dd4d052018b0")+		(uuid "ddfc40c4-e33c-493e-b735-24282440d539") 	) 	(fp_line 		(start 1.91 3.41)@@ -93,7 +93,7 @@ 			(type solid) 		) 		(layer "F.SilkS")-		(uuid "7b7161b8-bc72-4822-9d67-8c4bc120433f")+		(uuid "79366377-6a9f-460a-b0d1-788467590954") 	) 	(fp_poly 		(pts@@ -105,27 +105,27 @@ 		) 		(fill yes) 		(layer "F.SilkS")-		(uuid "818bd365-7a79-40a2-b037-dacc75b8af05")+		(uuid "27420593-f422-495a-9e17-88a99bcd8a3d") 	) 	(fp_line-		(start -1.85 -2.3)+		(start -1.85 -2.35) 		(end -1.85 3.35) 		(stroke 			(width 0.1) 			(type solid) 		) 		(layer "F.Fab")-		(uuid "2a9ca989-6b38-468d-a714-75a033988b2c")+		(uuid "659fc817-2286-4dd8-ba60-8e62262ce6cc") 	) 	(fp_line-		(start -1.85 -2.3)-		(end -0.8 -3.35)+		(start -1.85 -2.35)+		(end -0.85 -3.35) 		(stroke 			(width 0.1) 			(type solid) 		) 		(layer "F.Fab")-		(uuid "bcb7341f-c5b7-4cf0-ac84-66c574c5e61c")+		(uuid "f393364a-2641-4746-ba4c-6509ea1de503") 	) 	(fp_line 		(start -1.85 3.35)@@ -135,17 +135,17 @@ 			(type solid) 		) 		(layer "F.Fab")-		(uuid "c011dc66-40ad-4f1e-a34f-e251dae0cd31")+		(uuid "27db54e0-f4a8-4972-bcbc-256787416dcd") 	) 	(fp_line-		(start -0.8 -3.35)+		(start -0.85 -3.35) 		(end 1.85 -3.35) 		(stroke 			(width 0.1) 			(type solid) 		) 		(layer "F.Fab")-		(uuid "80711826-0dce-449b-af78-388864936159")+		(uuid "be579ebe-38db-4860-98f0-9f530f704760") 	) 	(fp_line 		(start 1.85 -3.35)@@ -155,12 +155,12 @@ 			(type solid) 		) 		(layer "F.Fab")-		(uuid "a66ee799-671f-4902-ac92-f94d39f82acf")+		(uuid "9d748ff0-f43a-42f3-a9ff-3a463972b1ca") 	) 	(fp_text user "${REFERENCE}" 		(at 0 0 90) 		(layer "F.Fab")-		(uuid "184c46b5-a004-48e0-8f63-d7d63dc324be")+		(uuid "aff1cd04-29c5-47f0-8349-1badf43ec67b") 		(effects 			(font 				(size 0.8 0.8)@@ -173,28 +173,28 @@ 		(size 2 1.5) 		(layers "F.Cu" "F.Mask" "F.Paste") 		(roundrect_rratio 0.25)-		(uuid "ea891fee-0855-44cc-8da9-0c7b9e3b1505")+		(uuid "6c38c733-73aa-46ef-9aa8-0adc47a79448") 	) 	(pad "2" smd roundrect 		(at -3.15 0) 		(size 2 1.5) 		(layers "F.Cu" "F.Mask" "F.Paste") 		(roundrect_rratio 0.25)-		(uuid "2adbaf0f-7617-4618-9438-78a8bd4ec4b2")+		(uuid "553b4aa3-b4fc-45ee-9bbe-5eb8183ee7d8") 	)-	(pad "3" smd roundrect-		(at -3.15 2.3)-		(size 2 1.5)+	(pad "2" smd roundrect+		(at 3.15 0)+		(size 2 3.8) 		(layers "F.Cu" "F.Mask" "F.Paste") 		(roundrect_rratio 0.25)-		(uuid "1b42a1a5-e735-42f2-b87a-1df5a461081d")+		(uuid "118e82e2-9099-4e46-a269-1e2cb8448d5e") 	)-	(pad "4" smd roundrect-		(at 3.15 0)-		(size 2 3.8)+	(pad "3" smd roundrect+		(at -3.15 2.3)+		(size 2 1.5) 		(layers "F.Cu" "F.Mask" "F.Paste") 		(roundrect_rratio 0.25)-		(uuid "023f2cc5-97fb-4421-8e37-e8aa385789b4")+		(uuid "5046df04-2b74-45a5-867e-e33a5e51e59c") 	) 	(embedded_fonts no) 	(model "${KICAD10_3DMODEL_DIR}/Package_TO_SOT_SMD.3dshapes/SOT-223.step"
zd1117iltr50.kicad_sym+1−5
@@ -16,11 +16,7 @@       (name "Vout" (effects (font (size 1.27 1.27))))       (number "2" (effects (font (size 1.27 1.27))))     )-    (pin passive line (at 17.78 0.00 180) (length 5.08)-      (name "EP" (effects (font (size 1.27 1.27))))-      (number "4" (effects (font (size 1.27 1.27))))-    )-    (pin power_in line (at 17.78 -2.54 180) (length 5.08)+    (pin power_in line (at 17.78 0.00 180) (length 5.08)       (name "Vin" (effects (font (size 1.27 1.27))))       (number "3" (effects (font (size 1.27 1.27))))     )
zd1117iltr50.lbr+8−10
@@ -52,12 +52,12 @@ <library> <description>Zetta Linear Voltage Regulators (LDO), SOT-223-4. Pinout cross-checked by two models against the datasheet</description> <packages>-<package name="SOT-223">+<package name="SOT-223-3_TabPin2">   <description>4 pads, 8.3 x 6.1 mm. module CMS SOT223 4 pins</description>   <smd name="1" x="-3.1500" y="2.3000" dx="2.0000" dy="1.5000" layer="1" roundness="50"/>   <smd name="2" x="-3.1500" y="-0.0000" dx="2.0000" dy="1.5000" layer="1" roundness="50"/>+  <smd name="2@2" x="3.1500" y="-0.0000" dx="2.0000" dy="3.8000" layer="1" roundness="50"/>   <smd name="3" x="-3.1500" y="-2.3000" dx="2.0000" dy="1.5000" layer="1" roundness="50"/>-  <smd name="4" x="3.1500" y="-0.0000" dx="2.0000" dy="3.8000" layer="1" roundness="50"/>   <polygon width="0.1200" layer="21">     <vertex x="-3.1300" y="3.3100"/>     <vertex x="-3.3700" y="3.6400"/>@@ -68,10 +68,10 @@   <wire x1="-1.8500" y1="-3.4100" x2="1.9100" y2="-3.4100" width="0.1200" layer="21"/>   <wire x1="1.9100" y1="3.4100" x2="1.9100" y2="2.1500" width="0.1200" layer="21"/>   <wire x1="1.9100" y1="-3.4100" x2="1.9100" y2="-2.1500" width="0.1200" layer="21"/>-  <wire x1="-1.8500" y1="2.3000" x2="-1.8500" y2="-3.3500" width="0.1000" layer="51"/>-  <wire x1="-1.8500" y1="2.3000" x2="-0.8000" y2="3.3500" width="0.1000" layer="51"/>+  <wire x1="-1.8500" y1="2.3500" x2="-1.8500" y2="-3.3500" width="0.1000" layer="51"/>+  <wire x1="-1.8500" y1="2.3500" x2="-0.8500" y2="3.3500" width="0.1000" layer="51"/>   <wire x1="-1.8500" y1="-3.3500" x2="1.8500" y2="-3.3500" width="0.1000" layer="51"/>-  <wire x1="-0.8000" y1="3.3500" x2="1.8500" y2="3.3500" width="0.1000" layer="51"/>+  <wire x1="-0.8500" y1="3.3500" x2="1.8500" y2="3.3500" width="0.1000" layer="51"/>   <wire x1="1.8500" y1="3.3500" x2="1.8500" y2="-3.3500" width="0.1000" layer="51"/>   <text x="0" y="4.010" size="1.27" layer="25" align="bottom-center">&gt;NAME</text>   <text x="0" y="-4.010" size="1.27" layer="27" align="top-center">&gt;VALUE</text>@@ -88,8 +88,7 @@   <text x="0.0000" y="-7.6200" size="1.27" layer="96" align="center">&gt;VALUE</text>   <pin name="Vss/ADJ" x="-17.78" y="0" length="middle" direction="pwr"/>   <pin name="Vout" x="-17.78" y="-2.54" length="middle" direction="out"/>-  <pin name="EP" x="17.78" y="0" length="middle" direction="pas" rot="R180"/>-  <pin name="Vin" x="17.78" y="-2.54" length="middle" direction="pwr" rot="R180"/>+  <pin name="Vin" x="17.78" y="0" length="middle" direction="pwr" rot="R180"/> </symbol> </symbols> <devicesets>@@ -99,11 +98,10 @@     <gate name="G$1" symbol="ZD1117ILTR50" x="0" y="0"/>   </gates>   <devices>-    <device name="" package="SOT-223">+    <device name="" package="SOT-223-3_TabPin2">       <connects>         <connect gate="G$1" pin="Vss/ADJ" pad="1"/>-        <connect gate="G$1" pin="Vout" pad="2"/>-        <connect gate="G$1" pin="EP" pad="4"/>+        <connect gate="G$1" pin="Vout" pad="2 2@2"/>         <connect gate="G$1" pin="Vin" pad="3"/>       </connects>       <technologies>