← Commit history
README.md+48−73
@@ -8,22 +8,22 @@ XD7705B from XINLUDA, in a DIP-16. Pinout and pin descriptions extracted from th  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | SCLK | input | Serial clock input for the three-wire SPI interface, which the datasheet describes as a Schmitt-trigger input. |-| 2 | XI | input | Clock input that accepts either a crystal or an external clock source for the master clock. |-| 3 | XO | output | Clock output for the crystal oscillator, which is left unconnected when an external clock is applied to XI. |-| 4 | CSN | input | Chip select input, active low; registers can only be read or written while CSN is pulled low. |-| 5 | RESET | input | Reset input, active low, which resets the logic, digital filter and modulator and restores registers to their default state. |-| 6 | AIN2P | input | Differential analogue positive input for channel 2. |-| 7 | AIN1P | input | Differential analogue positive input for channel 1. |-| 8 | AIN1N | input | Differential analogue negative input for channel 1. |-| 9 | REF INP | input | Positive input of the differential reference voltage; the datasheet requires REFINP > REFINN for correct operation. |-| 10 | REF INN | input | Negative input of the differential reference voltage; it must be below REFINP for correct operation. |-| 11 | AIN2N | input | Differential analogue negative input for channel 2. |-| 12 | OKL | output | AD conversion completion flag output: low indicates the ADC result register is updated and can be read, high indicates conversion or update is in progress. |-| 13 | DOUT | output | Serial data output; data is output on the falling edge of SCLK with the MSB first. |-| 14 | DIN | input | Serial data input; data is written on the rising edge of SCLK with the MSB first. |-| 15 | VDD | power_in | Power supply pin for the device, which operates at 3V or 5V with a ±5% range. |-| 16 | GND | power_in | Ground pin for the device. |+| 1 | SCLK | input | Serial clock input for reading and writing the on-chip registers, with Schmitt-trigger thresholds (VT+ 1.4 to 3 V and VT- 0.8 to 1.4 V at VDD=5 V; VT+ 1 to 2.5 V and VT- 0.4 to 1.1 V at VDD=3 V). |+| 2 | XI | input | Clock input for a crystal or external master clock, with a master clock range of 400 to 2500 kHz; input low/high levels are 0.8 V / 3.5 V at 5 V and 0.4 V / 2.5 V at 3 V. |+| 3 | XO | output | Clock output for the crystal oscillator (connects to the crystal circuit at XI). |+| 4 | CSN | input | Chip select, active low; registers can only be read or written while CSN is pulled low and CSN should be pulled high after the access. |+| 5 | RESET | input | Reset, active low; pulling it low resets all logic, digital filters and modulators and sets registers to default, with a minimum pulse width of 100 ns. |+| 6 | AIN2P | input | Differential analogue positive input for channel 2; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1). |+| 7 | AIN1P | input | Differential analogue positive input for channel 1; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1). |+| 8 | AIN1N | input | Differential analogue negative input for channel 1; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1). |+| 9 | REFINP | input | Positive input of the differential reference voltage; the datasheet requires REFINP to be greater than REFINN, with a reference of 1.225 V at 3 V supply or 2.5 V at 5 V supply, and references below 1 V raise output noise. |+| 10 | REFINN | input | Negative input of the differential reference voltage; the reference voltage range is 0 to VDD and REFINN must be less than REFINP. |+| 11 | AIN2N | input | Differential analogue negative input for channel 2; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1). |+| 12 | OKL | output | Conversion-complete flag output: low means the ADC result register has been updated and can be read, high means conversion or update is in progress and data must not be read. |+| 13 | DOUT | output | Serial data output, shifting the result MSB first with data updated on the falling edge of SCLK. |+| 14 | DIN | input | Serial data input, written on the rising edge of SCLK with a setup time of 30 ns and hold time of 20 ns. |+| 15 | VDD | power_in | Power supply, 3 V or 5 V operating voltage with ±5% range; absolute maximum is -0.3 V to 7 V. |+| 16 | GND | power_in | Ground pin. |  ## Key specifications @@ -40,65 +40,40 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---|-| Logic supply voltage | VDD | -0.3 |  | 7 | V |  | 3 |-| Analogue input voltage (max printed as VDD+0.3) | Vin | -0.3 |  |  | V |  | 3 |-| Digital input/output voltage (max printed as VDD+0.3) | Vout | -0.3 |  |  | V |  | 3 |-| Operating temperature range | Topr | -40 |  | 85 | ℃ |  | 3 |-| Storage temperature range | Tstg | -45 |  | 125 | ℃ |  | 3 |-| Junction temperature | Tj |  |  | 125 | ℃ |  | 3 |-| ESD Human-body model (HBM) rating |  |  |  | 2000 | V | Human-body model (HBM) | 3 |-| Integral nonlinearity |  | 0 |  | 0.01 | %of FSR |  | 3 |-| Bipolar negative full scale error |  | 0 |  | 0.01 | %of FSR/℃ |  | 3 |-| REF IN absolute/common mode voltage (max printed as VDD) |  | 0 |  |  | V |  | 3 |-| AIN absolute/common mode voltage (max printed as VDD+0.03) |  | -0.03 |  |  | V | BUFEN=0 | 3 |-| AIN absolute/common mode voltage (max printed as VDD-1.5) |  | 0.05 |  |  | V | BUFEN=1 | 3 |-| REFINP-REFINN difference |  | 1 |  | 1.75 | V | VDD=3V,Vref=1.225V | 3 |-| REFINP-REFINN difference |  | 1 |  | 3.5 | V | VDD=5V,Vref=2.5V | 3 |-| Input low level | VIL |  |  | 0.8 | V | VDD=5V | 4 |-| Input low level | VIL |  |  | 0.4 | V | VDD=3V | 4 |-| Input high level | VIH | 2 |  |  | V |  | 4 |-| Schmitt trigger input (SCLK) VT+ | VT+ | 1.4 |  | 3 | V | VDD=5V | 4 |-| Schmitt trigger input (SCLK) VT_ | VT_ | 0.8 |  | 1.4 | V |  | 4 |-| Schmitt trigger input (SCLK) hysteresis VT+-VT_ | VT+, VT_ | 0.4 |  | 0.8 | V |  | 4 |-| Schmitt trigger input (SCLK) VT+ | VT+ | 1 |  | 2.5 | V | VDD=3V | 4 |-| Schmitt trigger input (SCLK) VT_ | VT_ | 0.4 |  | 1.1 | V |  | 4 |-| Schmitt trigger input (SCLK) hysteresis VT+-VT_ (second row) | VT+ VT_ | 0.375 |  | 0.8 | V |  | 4 |+| Logic Supply Voltage | VDD | -0.3 |  | 7 | V | TA=+25℃ unless otherwise stated | 3 |+| Operating Temperature Range | Topr | -40 |  | 85 | ℃ | TA=+25℃ unless otherwise stated | 3 |+| Storage temperature range | Tstg | -45 |  | 125 | ℃ | TA=+25℃ unless otherwise stated | 3 |+| Junction temperature | Tj |  |  | 125 | ℃ | TA=+25℃ unless otherwise stated | 3 |+| Electrostatic discharge (ESD) Human-body model (HBM) |  |  |  | 2000 | V | Human-body model (HBM) | 3 |+| Analogue input voltage | Vin | -0.3 |  |  | V | TA=+25℃ unless otherwise stated; printed max is VDD+0.3 | 3 |+| Digital output voltage | Vout | -0.3 |  |  | V | TA=+25℃ unless otherwise stated; printed max is VDD+0.3 | 3 |+| Integral nonlinearity |  | 0 |  | 0.01 | %of FSR | Unless otherwise stated, VDD=+5V, REF=2.5V; TA=25℃ | 3 |+| Bipolar negative full scale error |  | 0 |  | 0.01 | %of FSR/℃ | Unless otherwise stated, VDD=+5V, REF=2.5V; TA=25℃ | 3 |+| REF IN Absolute/Common Mode Voltage |  | 0 |  |  | V | Unless otherwise stated, VDD=+5V, REF=2.5V; TA=25℃; printed max is VDD | 3 |+| AIN Absolute/Common Mode Voltage |  | -0.03 |  |  | V | BUFEN=0; printed max is VDD+0.03 | 3 |+| AIN Absolute/Common Mode Voltage |  | 0.05 |  |  | V | BUFEN=1; printed max is VDD-1.5 | 3 |+| AIN Differential voltage Unipolar input |  | 0 |  |  | V | Unipolar input; printed max is VREP/GAIN | 3 |+| REFINP-REFINN Difference |  | 1 |  | 1.75 | V | VDD=3V, Vref=1.225V | 3 |+| REFINP-REFINN Difference |  | 1 |  | 3.5 | V | VDD=5V, Vref=2.5V | 3 |+| VIL input low level | VIL |  |  | 0.8 | V | VDD=5V | 4 |+| VIL input low level | VIL |  |  | 0.4 | V | VDD=3V | 4 |+| VIH input high level | VIH | 2 |  |  | V |  | 4 |+| Schmitt trigger input (SCLK) positive threshold | VT+ | 1.4 |  | 3 | V | VDD=5V | 4 |+| Schmitt trigger input (SCLK) negative threshold | VT_ | 0.8 |  | 1.4 | V | VDD=5V | 4 |+| Schmitt trigger input (SCLK) hysteresis VT+-VT_ | VT+, VT_ | 0.4 |  | 0.8 | V | VDD=5V | 4 |+| Schmitt trigger input (SCLK) positive threshold | VT+ | 1 |  | 2.5 | V | VDD=3V | 4 |+| Schmitt trigger input (SCLK) negative threshold | VT_ | 0.4 |  | 1.1 | V | VDD=3V | 4 |+| Schmitt trigger input (SCLK) hysteresis VT+ VT_ | VT+ VT_ | 0.375 |  | 0.8 | V |  | 4 | | XI input low level |  |  |  | 0.8 | V | VDD=5V | 4 | | XI input high level |  | 3.5 |  |  | V | VDD=5V | 4 | | XI input low level |  |  |  | 0.4 | V | VDD=3V | 4 |-| XI input high level |  | 2.5 |  |  | V | VDD=3V | 3 |-| Master clock frequency | fCLKIN |  | 400 | 2500 | kHz |  | 5 |-| RESET pulse width | tR | 100 |  |  | ns |  | 5 |-| CSN↓ to SCLK first rising edge | Tcsn1 | 120 |  |  | ns |  | 5 |-| SCLK↓ to DIN effective acquisition interval | tdo | 0 |  | 80 | ns | VDD=5V | 5 |-| SCLK↓ to DIN effective acquisition interval | tdo | 0 |  | 100 | ns | VDD=3V | 5 |-| SCLK↑ to CSN↑ hold | Tcsn2 | 0 |  |  | ns |  | 5 |-| SCLK↑ post-bus withdrawal time | tsout | 10 |  | 60 | ns | VDD=5V | 5 |-| SCLK↑ post-bus withdrawal time | tsout |  |  | 100 | ns | VDD=3V | 5 |-| DIN effective to SCLK↑ acquisition time | tds | 30 |  |  | ns |  | 5 |-| DIN effective to SCLK↑ holding time | tdh | 20 |  |  | ns |  | 5 |-| OKL↓ to CSN↓ holding time | toc | 0 |  |  | ns |  | 5 |-| Clock pulse width high (low) level | tspw | 100 |  |  | ns |  | 5 |-| Unipolar misalignment drift |  |  | 0.5 |  | μV/℃ |  | 3 |-| Bipolar zero drift |  |  | 0.5 |  | μV/℃ | PGA=1-4 | 3 |-| Bipolar zero drift |  |  | 0.1 |  | μV/℃ | PGA=8-128 | 3 |-| Full scale drift |  |  | 0.5 |  | μV/℃ |  | 3 |-| Gain error drift |  |  | 0.5 |  | ppm of FSR/℃ |  | 3 |-| Bipolar negative full scale drift |  |  | 1 |  | μV/℃ |  | 3 |-| AIN input current |  |  | 1 |  | nA |  | 3 |-| Supply current (3V) |  |  | 0.32 |  | mA | 3V supply, BUFEN=0, fCLKIN=1 MHZ, Gain 1-128, XI and OSCDIS=1 | 4 |-| Supply current (3V) |  |  | 0.6 |  | mA | 3V supply, BUFEN=1, fCLKIN=1 MHZ, Gain 1-128, XI and OSCDIS=1 | 4 |-| Supply current (3V) |  |  | 0.4 |  | mA | 3V supply, BUFEN=0, fCLKIN=2.4576 MHZ, Gain 1-4, XI and OSCDIS=1 | 4 |-| Supply current (3V) |  |  | 0.7 |  | mA | 3V supply, BUFEN=1, fCLKIN=2.4576 MHZ, Gain 1-4, XI and OSCDIS=1 | 4 |-| Supply current (3V) |  |  | 1.1 |  | mA | 3V supply, BUFEN=1, fCLKIN=2.4576 MHZ, Gain 8-128, XI and OSCDIS=1 | 4 |-| Supply current (5V) |  |  | 0.45 |  | mA | 5V supply, BUFEN=0, fCLKIN=1 MHZ, Gain 1-128, XI and OSCDIS=1 | 4 |-| Supply current (5V) |  |  | 0.7 |  | mA | 5V supply, BUFEN=1, fCLKIN=1 MHZ, Gain 1-128, XI and OSCDIS=1 | 4 |-| Supply current (5V) |  |  | 0.6 |  | mA | 5V supply, BUFEN=0, fCLKIN=2.4576 MHZ, Gain 1-4, XI and OSCDIS=1 | 4 |-| Supply current (5V) |  |  | 0.85 |  | mA | 5V supply, BUFEN=0, fCLKIN=2.4576 MHZ, Gain 8-128, XI and OSCDIS=1 | 4 |-| Supply current (5V) |  |  | 0.9 |  | mA | 5V supply, BUFEN=1, fCLKIN=2.4576 MHZ, Gain 1-4, XI and OSCDIS=1 | 4 |-| Supply current (5V) |  |  | 1.3 |  | mA | 5V supply, BUFEN=1, fCLKIN=2.4576 MHZ, Gain 8-128, XI and OSCDIS=1 | 4 |-| Power-down mode current |  |  | 16 |  | uA | VDD=5V, XI=0V/VDD | 4 |-| Power-down mode current |  |  | 8 |  | uA | VDD=3V, XI=0V/VDD | 4 |+| XI input high level |  | 2.5 |  |  | V | VDD=3V | 4 |+| Power-down mode current |  |  |  | 16 | uA | VDD=5V, XI=0V/VDD | 4 |+| Power-down mode current |  |  |  | 8 | uA | VDD=3V, XI=0V/VDD | 4 |+| Master Clock Frequency | fCLKIN | 400 |  | 2500 | kHz |  | 5 |+| Slck↓→DIN Effective acquisition interval | tdo | 0 |  | 80 | ns | VDD=5V | 5 |+| Slck↓→DIN Effective acquisition interval | tdo | 0 |  | 100 | ns | VDD=3V | 5 |+| SCLK↑ Post-bus withdrawal time | tsout | 10 |  | 60 | ns | VDD=5V | 5 |  ## CAD (KiCad official) @@ -111,7 +86,7 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [XINLUDA datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588896416454348800) (12 pp, sha256 `91725263468fc1bc`, retrieved 2026-11-10, tier: lcsc)+- **Datasheet:** [XINLUDA datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588896416454348800) (12 pp, sha256 `91725263468fc1bc`, retrieved 2026-11-11, tier: lcsc) - **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** KiCad official libraries (CC-BY-SA 4.0). 
package.json+27−28
@@ -1,6 +1,6 @@ {   "slug": "xd7705b",-  "version": "0.1.0",+  "version": "0.1.1",   "type": "component",   "description": "XINLUDA Analog To Digital Converters (ADC), DIP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -52,12 +52,11 @@       "lcsc": "C521176"     },     "distributor_check": {-      "checked_at": "2026-11-10T08:15:55Z",+      "checked_at": "2026-11-11T01:18:20Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": null,-        "status": "deferred",-        "error": "shared DigiKey quota guard: 996 calls left today"+        "status": "no match"       },       "mouser": {         "pn": null,@@ -69,97 +68,97 @@         "number": "1",         "name": "SCLK",         "type": "input",-        "description": "Serial clock input for the three-wire SPI interface, which the datasheet describes as a Schmitt-trigger input."+        "description": "Serial clock input for reading and writing the on-chip registers, with Schmitt-trigger thresholds (VT+ 1.4 to 3 V and VT- 0.8 to 1.4 V at VDD=5 V; VT+ 1 to 2.5 V and VT- 0.4 to 1.1 V at VDD=3 V)."       },       {         "number": "2",         "name": "XI",         "type": "input",-        "description": "Clock input that accepts either a crystal or an external clock source for the master clock."+        "description": "Clock input for a crystal or external master clock, with a master clock range of 400 to 2500 kHz; input low/high levels are 0.8 V / 3.5 V at 5 V and 0.4 V / 2.5 V at 3 V."       },       {         "number": "3",         "name": "XO",         "type": "output",-        "description": "Clock output for the crystal oscillator, which is left unconnected when an external clock is applied to XI."+        "description": "Clock output for the crystal oscillator (connects to the crystal circuit at XI)."       },       {         "number": "4",         "name": "CSN",         "type": "input",-        "description": "Chip select input, active low; registers can only be read or written while CSN is pulled low."+        "description": "Chip select, active low; registers can only be read or written while CSN is pulled low and CSN should be pulled high after the access."       },       {         "number": "5",         "name": "RESET",         "type": "input",-        "description": "Reset input, active low, which resets the logic, digital filter and modulator and restores registers to their default state."+        "description": "Reset, active low; pulling it low resets all logic, digital filters and modulators and sets registers to default, with a minimum pulse width of 100 ns."       },       {         "number": "6",         "name": "AIN2P",         "type": "input",-        "description": "Differential analogue positive input for channel 2."+        "description": "Differential analogue positive input for channel 2; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1)."       },       {         "number": "7",         "name": "AIN1P",         "type": "input",-        "description": "Differential analogue positive input for channel 1."+        "description": "Differential analogue positive input for channel 1; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1)."       },       {         "number": "8",         "name": "AIN1N",         "type": "input",-        "description": "Differential analogue negative input for channel 1."+        "description": "Differential analogue negative input for channel 1; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1)."       },       {         "number": "9",-        "name": "REF INP",+        "name": "REFINP",         "type": "input",-        "description": "Positive input of the differential reference voltage; the datasheet requires REFINP > REFINN for correct operation."+        "description": "Positive input of the differential reference voltage; the datasheet requires REFINP to be greater than REFINN, with a reference of 1.225 V at 3 V supply or 2.5 V at 5 V supply, and references below 1 V raise output noise."       },       {         "number": "10",-        "name": "REF INN",+        "name": "REFINN",         "type": "input",-        "description": "Negative input of the differential reference voltage; it must be below REFINP for correct operation."+        "description": "Negative input of the differential reference voltage; the reference voltage range is 0 to VDD and REFINN must be less than REFINP."       },       {         "number": "11",         "name": "AIN2N",         "type": "input",-        "description": "Differential analogue negative input for channel 2."+        "description": "Differential analogue negative input for channel 2; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1)."       },       {         "number": "12",         "name": "OKL",         "type": "output",-        "description": "AD conversion completion flag output: low indicates the ADC result register is updated and can be read, high indicates conversion or update is in progress."+        "description": "Conversion-complete flag output: low means the ADC result register has been updated and can be read, high means conversion or update is in progress and data must not be read."       },       {         "number": "13",         "name": "DOUT",         "type": "output",-        "description": "Serial data output; data is output on the falling edge of SCLK with the MSB first."+        "description": "Serial data output, shifting the result MSB first with data updated on the falling edge of SCLK."       },       {         "number": "14",         "name": "DIN",         "type": "input",-        "description": "Serial data input; data is written on the rising edge of SCLK with the MSB first."+        "description": "Serial data input, written on the rising edge of SCLK with a setup time of 30 ns and hold time of 20 ns."       },       {         "number": "15",         "name": "VDD",         "type": "power_in",-        "description": "Power supply pin for the device, which operates at 3V or 5V with a ±5% range."+        "description": "Power supply, 3 V or 5 V operating voltage with ±5% range; absolute maximum is -0.3 V to 7 V."       },       {         "number": "16",         "name": "GND",         "type": "power_in",-        "description": "Ground pin for the device."+        "description": "Ground pin."       }     ],     "provenance": {@@ -173,11 +172,11 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The pin table on page 2 is shared by the DIP-16 (XD7705B) and SOP-16W (XL7705B) packages. The orderi; Pin descriptions for VDD (operating range) are taken from the features and electrical sections, and "+          "extractor flagged: The pin table on page 2 is shared by DIP-16 and SOP-16W and uses the same numbering; the ordering ta; The datasheet gives XO only as 'clock output' with type O and no electrical limits; the description ; The datasheet pin table lists VDD and GND with type '-'; power_in was assigned for KiCad ERC. The 16"         ],         "pages_sent": 12,-        "cost_usd": 0.0482,-        "at": "2026-11-10T08:15:48"+        "cost_usd": 0.0494,+        "at": "2026-11-11T01:18:08"       },       "datasheet": {         "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588896416454348800",@@ -214,7 +213,7 @@         "centre_offset_mm": 0.0,         "footprint_binding": "identity",         "sha256": "17a30b1f0ab3fd5384a1231e3c63c394888d5b952c542a8c189e023ed3467464",-        "checked": "2026-11-10",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -232,8 +231,8 @@         "zmin_mm": -3.3,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "54611277cd622fca54605419fddd0ebf54cc72fbea058e17bde3b6c3b8792a61",-        "checked": "2026-11-10",+        "sha256": "98d47a5f477df2f50a6de0445d4246c43daf5d1d4d0ad78d531262681744d877",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]
page.json+30−29
@@ -4,7 +4,7 @@   "slug": "xd7705b",   "title": "XD7705B",   "brief": "XINLUDA Analog To Digital Converters (ADC), DIP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.1.1",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -34,12 +34,11 @@       "lcsc": "C521176"     },     "distributor_check": {-      "checked_at": "2026-11-10T08:15:55Z",+      "checked_at": "2026-11-11T01:18:20Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": null,-        "status": "deferred",-        "error": "shared DigiKey quota guard: 996 calls left today"+        "status": "no match"       },       "mouser": {         "pn": null,@@ -51,97 +50,97 @@         "number": "1",         "name": "SCLK",         "type": "input",-        "description": "Serial clock input for the three-wire SPI interface, which the datasheet describes as a Schmitt-trigger input."+        "description": "Serial clock input for reading and writing the on-chip registers, with Schmitt-trigger thresholds (VT+ 1.4 to 3 V and VT- 0.8 to 1.4 V at VDD=5 V; VT+ 1 to 2.5 V and VT- 0.4 to 1.1 V at VDD=3 V)."       },       {         "number": "2",         "name": "XI",         "type": "input",-        "description": "Clock input that accepts either a crystal or an external clock source for the master clock."+        "description": "Clock input for a crystal or external master clock, with a master clock range of 400 to 2500 kHz; input low/high levels are 0.8 V / 3.5 V at 5 V and 0.4 V / 2.5 V at 3 V."       },       {         "number": "3",         "name": "XO",         "type": "output",-        "description": "Clock output for the crystal oscillator, which is left unconnected when an external clock is applied to XI."+        "description": "Clock output for the crystal oscillator (connects to the crystal circuit at XI)."       },       {         "number": "4",         "name": "CSN",         "type": "input",-        "description": "Chip select input, active low; registers can only be read or written while CSN is pulled low."+        "description": "Chip select, active low; registers can only be read or written while CSN is pulled low and CSN should be pulled high after the access."       },       {         "number": "5",         "name": "RESET",         "type": "input",-        "description": "Reset input, active low, which resets the logic, digital filter and modulator and restores registers to their default state."+        "description": "Reset, active low; pulling it low resets all logic, digital filters and modulators and sets registers to default, with a minimum pulse width of 100 ns."       },       {         "number": "6",         "name": "AIN2P",         "type": "input",-        "description": "Differential analogue positive input for channel 2."+        "description": "Differential analogue positive input for channel 2; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1)."       },       {         "number": "7",         "name": "AIN1P",         "type": "input",-        "description": "Differential analogue positive input for channel 1."+        "description": "Differential analogue positive input for channel 1; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1)."       },       {         "number": "8",         "name": "AIN1N",         "type": "input",-        "description": "Differential analogue negative input for channel 1."+        "description": "Differential analogue negative input for channel 1; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1)."       },       {         "number": "9",-        "name": "REF INP",+        "name": "REFINP",         "type": "input",-        "description": "Positive input of the differential reference voltage; the datasheet requires REFINP > REFINN for correct operation."+        "description": "Positive input of the differential reference voltage; the datasheet requires REFINP to be greater than REFINN, with a reference of 1.225 V at 3 V supply or 2.5 V at 5 V supply, and references below 1 V raise output noise."       },       {         "number": "10",-        "name": "REF INN",+        "name": "REFINN",         "type": "input",-        "description": "Negative input of the differential reference voltage; it must be below REFINP for correct operation."+        "description": "Negative input of the differential reference voltage; the reference voltage range is 0 to VDD and REFINN must be less than REFINP."       },       {         "number": "11",         "name": "AIN2N",         "type": "input",-        "description": "Differential analogue negative input for channel 2."+        "description": "Differential analogue negative input for channel 2; absolute/common-mode range is -0.03 V to VDD+0.03 V with the buffer disabled (BUFEN=0) and 0.05 V to VDD-1.5 V with the buffer enabled (BUFEN=1)."       },       {         "number": "12",         "name": "OKL",         "type": "output",-        "description": "AD conversion completion flag output: low indicates the ADC result register is updated and can be read, high indicates conversion or update is in progress."+        "description": "Conversion-complete flag output: low means the ADC result register has been updated and can be read, high means conversion or update is in progress and data must not be read."       },       {         "number": "13",         "name": "DOUT",         "type": "output",-        "description": "Serial data output; data is output on the falling edge of SCLK with the MSB first."+        "description": "Serial data output, shifting the result MSB first with data updated on the falling edge of SCLK."       },       {         "number": "14",         "name": "DIN",         "type": "input",-        "description": "Serial data input; data is written on the rising edge of SCLK with the MSB first."+        "description": "Serial data input, written on the rising edge of SCLK with a setup time of 30 ns and hold time of 20 ns."       },       {         "number": "15",         "name": "VDD",         "type": "power_in",-        "description": "Power supply pin for the device, which operates at 3V or 5V with a ±5% range."+        "description": "Power supply, 3 V or 5 V operating voltage with ±5% range; absolute maximum is -0.3 V to 7 V."       },       {         "number": "16",         "name": "GND",         "type": "power_in",-        "description": "Ground pin for the device."+        "description": "Ground pin."       }     ],     "provenance": {@@ -155,11 +154,11 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The pin table on page 2 is shared by the DIP-16 (XD7705B) and SOP-16W (XL7705B) packages. The orderi; Pin descriptions for VDD (operating range) are taken from the features and electrical sections, and "+          "extractor flagged: The pin table on page 2 is shared by DIP-16 and SOP-16W and uses the same numbering; the ordering ta; The datasheet gives XO only as 'clock output' with type O and no electrical limits; the description ; The datasheet pin table lists VDD and GND with type '-'; power_in was assigned for KiCad ERC. The 16"         ],         "pages_sent": 12,-        "cost_usd": 0.0482,-        "at": "2026-11-10T08:15:48"+        "cost_usd": 0.0494,+        "at": "2026-11-11T01:18:08"       },       "datasheet": {         "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588896416454348800",@@ -196,7 +195,7 @@         "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "17a30b1f0ab3fd5384a1231e3c63c394888d5b952c542a8c189e023ed3467464",-        "checked": "2026-11-10",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -214,8 +213,8 @@         "zmin_mm": -3.3,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "54611277cd622fca54605419fddd0ebf54cc72fbea058e17bde3b6c3b8792a61",-        "checked": "2026-11-10",+        "sha256": "98d47a5f477df2f50a6de0445d4246c43daf5d1d4d0ad78d531262681744d877",+        "checked": "2026-11-11",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]@@ -982,5 +981,7 @@   ],   "visibility": {     "public": true-  }+  },+  "description": "XINLUDA Analog To Digital Converters (ADC), DIP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file
xd7705b-hero.glb
⋯ 1 unchanged line ⋯
xd7705b-hero.overlay.json+4−4
@@ -79,9 +79,9 @@     "footprint": "xd7705b.kicad_mod",     "footprint_sha256": "d9f5f5a3dbebef059800781d37575e4120e5ae5e7fd96001eda365f65de94485",     "pins": "page.json component.pins",-    "pins_sha256": "860b10e5b928f76fdfbcc48d69497ea30b8c62d13f9ec78f2bfd0e706051948d"+    "pins_sha256": "dedf626c3673ed82d367636ee78c382d6c782b2f21cb708500af8e8e7cb4dcac"   },-  "generator": "adom-wiki 1.8.15 (component_hero)",+  "generator": "adom-wiki 1.8.18 (component_hero)",   "labels": [     {       "pad": "1",@@ -157,7 +157,7 @@     },     {       "pad": "9",-      "text": "REF INP",+      "text": "REFINP",       "x": 8.57,       "y": 17.78,       "align": "left",@@ -166,7 +166,7 @@     },     {       "pad": "10",-      "text": "REF INN",+      "text": "REFINN",       "x": 8.57,       "y": 15.24,       "align": "left",
xd7705b.kicad_sym+2−2
@@ -65,11 +65,11 @@       (number "11" (effects (font (size 1.27 1.27))))     )     (pin input line (at 17.78 -7.62 180) (length 5.08)-      (name "REF INN" (effects (font (size 1.27 1.27))))+      (name "REFINN" (effects (font (size 1.27 1.27))))       (number "10" (effects (font (size 1.27 1.27))))     )     (pin input line (at 17.78 -10.16 180) (length 5.08)-      (name "REF INP" (effects (font (size 1.27 1.27))))+      (name "REFINP" (effects (font (size 1.27 1.27))))       (number "9" (effects (font (size 1.27 1.27))))     )     )
xd7705b.lbr+16−7
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>XINLUDA Analog To Digital Converters (ADC), DIP-16. Pinout cross-checked by two models against the datasheet</description> <packages> <package name="DIP-16_W7.62mm">   <description>16 pads, 9.2 x 19.4 mm. 16-lead though-hole mounted DIP package, row spacing 7.62mm (300 mils)</description>@@ -98,6 +98,7 @@ </packages> <symbols> <symbol name="XD7705B">+  <description>XINLUDA Analog To Digital Converters (ADC), DIP-16. Pinout cross-checked by two models against the datasheet</description>   <wire x1="-12.7" y1="10.16" x2="12.7" y2="10.16" width="0.254" layer="94"/>   <wire x1="12.7" y1="10.16" x2="12.7" y2="-12.7" width="0.254" layer="94"/>   <wire x1="12.7" y1="-12.7" x2="-12.7" y2="-12.7" width="0.254" layer="94"/>@@ -118,13 +119,13 @@   <pin name="DOUT" x="17.78" y="0" length="middle" direction="out" rot="R180"/>   <pin name="OKL" x="17.78" y="-2.54" length="middle" direction="out" rot="R180"/>   <pin name="AIN2N" x="17.78" y="-5.08" length="middle" direction="in" rot="R180"/>-  <pin name="REF_INN" x="17.78" y="-7.62" length="middle" direction="in" rot="R180"/>-  <pin name="REF_INP" x="17.78" y="-10.16" length="middle" direction="in" rot="R180"/>+  <pin name="REFINN" x="17.78" y="-7.62" length="middle" direction="in" rot="R180"/>+  <pin name="REFINP" x="17.78" y="-10.16" length="middle" direction="in" rot="R180"/> </symbol> </symbols> <devicesets> <deviceset name="XD7705B" prefix="U">-  <description></description>+  <description>XINLUDA Analog To Digital Converters (ADC), DIP-16. Pinout cross-checked by two models against the datasheet</description>   <gates>     <gate name="G$1" symbol="XD7705B" x="0" y="0"/>   </gates>@@ -145,10 +146,18 @@         <connect gate="G$1" pin="DOUT" pad="13"/>         <connect gate="G$1" pin="OKL" pad="12"/>         <connect gate="G$1" pin="AIN2N" pad="11"/>-        <connect gate="G$1" pin="REF_INN" pad="10"/>-        <connect gate="G$1" pin="REF_INP" pad="9"/>+        <connect gate="G$1" pin="REFINN" pad="10"/>+        <connect gate="G$1" pin="REFINP" pad="9"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="XD7705B" constant="no"/>+          <attribute name="MANUFACTURER" value="XINLUDA" constant="no"/>+          <attribute name="DATASHEET" value="https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588896416454348800" constant="no"/>+          <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/xd7705b" constant="no"/>+          <attribute name="LCSC_PN" value="C521176" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>