← Commit history

Initial commit: component/w5100s-l

Ray ·7aaa854c52 ·
2 files changed +465
README.mdadded+84
@@ -0,0 +1,84 @@+# W5100S-L++**WIZNET** · Ethernet Transceivers · LQFP-48(7x7)++W5100S-L from WIZNET, in a LQFP-48(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | GNDA | power_in | Analog ground connection. |+| 2 | TXON | output | Differential transmitted signal pair (negative); differential data is transmitted to media via TXOP/TXON signal pair on MDI mode. |+| 3 | TXOP | output | Differential transmitted signal pair (positive); differential data is transmitted to media via TXOP/TXON signal pair on MDI mode. |+| 4 | 1V2A | power_in | Analog 1.2V power; supplied from 1V20 voltage source. |+| 5 | RXIN | input | Differential received signal pair (negative); differential data is received from media via RXIP/RXIN signal pair on MDI mode. |+| 6 | RXIP | input | Differential received signal pair (positive); differential data is received from media via RXIP/RXIN signal pair on MDI mode. |+| 7 | GNDA | power_in | Analog ground connection. |+| 8 | 3V3A | power_in | Analog 3.3V power. |+| 9 | RSET_BG | output | Off-chip bias resistor connection; must be connected to analog ground through external 12.3kΩ ±1% resistor. |+| 10 | GND | power_in | Digital ground connection. |+| 11 | XSCO | output | 25MHz clock output for crystal oscillator (TXAL) or external oscillator; used for internal clock stabilization. |+| 12 | XSCI | input | 25MHz clock input for crystal oscillator (TXAL) or external oscillator; used for internal clock stabilization. |+| 13 | 1V2D | power_in | Digital 1.2V power; supplied from 1V20 voltage source. |+| 14 | 1V2O | power_out | Internal regulator 1.2V power output with maximum 150mA capacity; must use ferrite bead filter and 3.3µF external capacitors. |+| 15 | 3V3A | power_in | Analog 3.3V power. |+| 16 | GNDA | power_in | Analog ground connection. |+| 17 | LNKn | output | Link status LED output; low indicates link up, high indicates link down (valid in SPI and parallel bus modes). |+| 18 | SPDn | output | Link speed LED output; low indicates 100Mbps, high indicates 10Mbps (valid in SPI and parallel bus modes). |+| 19 | DPXn | output | Link duplex LED output; low indicates full-duplex, high indicates half-duplex (valid in SPI and parallel bus modes). |+| 20 | ACTn | output | Link activity LED output; flashes during link up with TX/RX, high during link down (valid in SPI and parallel bus modes). |+| 21 | COLn | output | Link collision detect LED output; low indicates collision detected, high indicates no collision (valid in SPI and parallel bus modes). |+| 22 | 1V2D | power_in | Digital 1.2V power; supplied from 1V20 voltage source. |+| 23 | GND | power_in | Digital ground connection. |+| 24 | 3V3D | power_in | Digital 3.3V power. |+| 25 | MOD[0] | input | Interface mode selection bit 0; modes: 0000=SPI, 010X=parallel bus; must be strapped before chip enable. |+| 26 | MOD[1] | input | Interface mode selection bit 1; modes: 0000=SPI, 010X=parallel bus; must be strapped before chip enable. |+| 27 | MOD[2] | input | Interface mode selection bit 2; modes: 0000=SPI, 010X=parallel bus; must be strapped before chip enable. |+| 28 | MOD[3] | input | Interface mode selection bit 3; modes: 0000=SPI, 010X=parallel bus; must be strapped before chip enable. |+| 29 | CSn | input | Chip select input with internal 75kΩ pull-up resistor; low selects W5100S, high deselects. |+| 30 | SCLK | input | SPI clock input in SPI mode; must be connected to GND or floated in parallel bus mode. |+| 31 | 1V2D | power_in | Digital 1.2V power; supplied from 1V20 voltage source. |+| 32 | MOSI/ADDR0 | input | SPI master output slave input (data input) in SPI mode; address bit 0 in parallel bus mode. |+| 33 | MISO/ADDR1 | bidirectional | SPI master input slave output (data output) in SPI mode; address bit 1 in parallel bus mode. |+| 34 | RDn | input | Read strobe input with internal 75kΩ pull-up resistor in parallel bus mode; must be connected to 3V3D or floated in SPI mode. |+| 35 | WRn | input | Write strobe input with internal 75kΩ pull-up resistor in parallel bus mode indicating write operation. |+| 36 | 3V3D | power_in | Digital 3.3V power. |+| 37 | DAT0 | bidirectional | 8-bit data bus bit 0; receives or transmits data from/to host in parallel bus mode; must be floated in SPI mode. |+| 38 | DAT1 | bidirectional | 8-bit data bus bit 1 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode. |+| 39 | DAT2 | bidirectional | 8-bit data bus bit 2 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode. |+| 40 | DAT3 | bidirectional | 8-bit data bus bit 3 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode. |+| 41 | DAT4 | bidirectional | 8-bit data bus bit 4 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode. |+| 42 | DAT5 | bidirectional | 8-bit data bus bit 5 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode. |+| 43 | DAT6 | bidirectional | 8-bit data bus bit 6; receives or transmits data from/to host in parallel bus mode; must be floated in SPI mode. |+| 44 | DAT7 | bidirectional | 8-bit data bus bit 7; receives or transmits data from/to host in parallel bus mode; must be floated in SPI mode. |+| 45 | 1V2D | power_in | Digital 1.2V power; supplied from 1V20 voltage source. |+| 46 | GND | power_in | Digital ground connection. |+| 47 | INTn | output | Interrupt output to host; low indicates interrupt occurred, high indicates no interrupt; polarity controlled via MR2[IEN]. |+| 48 | RSTn | input | Reset input with internal pull-up resistor; must be asserted low for minimum 500ns; W5100S requires 60.3ms initialization after reset release. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | WIZNET |+| Package | LQFP-48(7x7) |+| Category | Interface |+| Pins | 48 |++## CAD (KiCad official)++- Symbol: `W5100S-L`+- Footprint: `Package_QFP:LQFP-48_7x7mm_P0.5mm`+- 3D model: LQFP-48(7x7) (KiCad packages3D, STEP)+- 3D model files: `w5100s-l-etched.step` / `w5100s-l-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `w5100s-l.step` / `w5100s-l.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [WIZNET datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586185150207680512) (109 pp, sha256 `fca425bbdeeb7ace`, retrieved 2026-09-22, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/w5100s-l-datasheet.pdf)
page.jsonadded+381
@@ -0,0 +1,381 @@+{+  "slug": "w5100s-l",+  "version": "0.1.0",+  "type": "component",+  "description": "WIZNET Ethernet Transceivers, LQFP-48(7x7). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "interface",+    "w5100s-l",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "w5100s-l.kicad_sym",+    "w5100s-l.kicad_mod",+    "w5100s-l.glb",+    "w5100s-l.step",+    "w5100s-l.lbr",+    "docs/hero.png",+    "docs/w5100s-l-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "W5100S-L",+    "manufacturer": "WIZNET",+    "package": "LQFP-48(7x7)",+    "pin_count": 48,+    "category": "Interface",+    "subcategory": "Ethernet Transceivers",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586185150207680512",+    "parts": {+      "symbol": "w5100s-l.kicad_sym",+      "footprint": "w5100s-l.kicad_mod",+      "model_3d": "w5100s-l-etched.glb",+      "model_3d_plain": "w5100s-l.glb",+      "model_3d_step": "w5100s-l-etched.step",+      "model_3d_step_plain": "w5100s-l.step",+      "lbr": "w5100s-l.lbr"+    },+    "distributor_links": {+      "lcsc": "C194673"+    },+    "pins": [+      {+        "number": "1",+        "name": "GNDA",+        "type": "power_in",+        "description": "Analog ground connection."+      },+      {+        "number": "2",+        "name": "TXON",+        "type": "output",+        "description": "Differential transmitted signal pair (negative); differential data is transmitted to media via TXOP/TXON signal pair on MDI mode."+      },+      {+        "number": "3",+        "name": "TXOP",+        "type": "output",+        "description": "Differential transmitted signal pair (positive); differential data is transmitted to media via TXOP/TXON signal pair on MDI mode."+      },+      {+        "number": "4",+        "name": "1V2A",+        "type": "power_in",+        "description": "Analog 1.2V power; supplied from 1V20 voltage source."+      },+      {+        "number": "5",+        "name": "RXIN",+        "type": "input",+        "description": "Differential received signal pair (negative); differential data is received from media via RXIP/RXIN signal pair on MDI mode."+      },+      {+        "number": "6",+        "name": "RXIP",+        "type": "input",+        "description": "Differential received signal pair (positive); differential data is received from media via RXIP/RXIN signal pair on MDI mode."+      },+      {+        "number": "7",+        "name": "GNDA",+        "type": "power_in",+        "description": "Analog ground connection."+      },+      {+        "number": "8",+        "name": "3V3A",+        "type": "power_in",+        "description": "Analog 3.3V power."+      },+      {+        "number": "9",+        "name": "RSET_BG",+        "type": "output",+        "description": "Off-chip bias resistor connection; must be connected to analog ground through external 12.3kΩ ±1% resistor."+      },+      {+        "number": "10",+        "name": "GND",+        "type": "power_in",+        "description": "Digital ground connection."+      },+      {+        "number": "11",+        "name": "XSCO",+        "type": "output",+        "description": "25MHz clock output for crystal oscillator (TXAL) or external oscillator; used for internal clock stabilization."+      },+      {+        "number": "12",+        "name": "XSCI",+        "type": "input",+        "description": "25MHz clock input for crystal oscillator (TXAL) or external oscillator; used for internal clock stabilization."+      },+      {+        "number": "13",+        "name": "1V2D",+        "type": "power_in",+        "description": "Digital 1.2V power; supplied from 1V20 voltage source."+      },+      {+        "number": "14",+        "name": "1V2O",+        "type": "power_out",+        "description": "Internal regulator 1.2V power output with maximum 150mA capacity; must use ferrite bead filter and 3.3µF external capacitors."+      },+      {+        "number": "15",+        "name": "3V3A",+        "type": "power_in",+        "description": "Analog 3.3V power."+      },+      {+        "number": "16",+        "name": "GNDA",+        "type": "power_in",+        "description": "Analog ground connection."+      },+      {+        "number": "17",+        "name": "LNKn",+        "type": "output",+        "description": "Link status LED output; low indicates link up, high indicates link down (valid in SPI and parallel bus modes)."+      },+      {+        "number": "18",+        "name": "SPDn",+        "type": "output",+        "description": "Link speed LED output; low indicates 100Mbps, high indicates 10Mbps (valid in SPI and parallel bus modes)."+      },+      {+        "number": "19",+        "name": "DPXn",+        "type": "output",+        "description": "Link duplex LED output; low indicates full-duplex, high indicates half-duplex (valid in SPI and parallel bus modes)."+      },+      {+        "number": "20",+        "name": "ACTn",+        "type": "output",+        "description": "Link activity LED output; flashes during link up with TX/RX, high during link down (valid in SPI and parallel bus modes)."+      },+      {+        "number": "21",+        "name": "COLn",+        "type": "output",+        "description": "Link collision detect LED output; low indicates collision detected, high indicates no collision (valid in SPI and parallel bus modes)."+      },+      {+        "number": "22",+        "name": "1V2D",+        "type": "power_in",+        "description": "Digital 1.2V power; supplied from 1V20 voltage source."+      },+      {+        "number": "23",+        "name": "GND",+        "type": "power_in",+        "description": "Digital ground connection."+      },+      {+        "number": "24",+        "name": "3V3D",+        "type": "power_in",+        "description": "Digital 3.3V power."+      },+      {+        "number": "25",+        "name": "MOD[0]",+        "type": "input",+        "description": "Interface mode selection bit 0; modes: 0000=SPI, 010X=parallel bus; must be strapped before chip enable."+      },+      {+        "number": "26",+        "name": "MOD[1]",+        "type": "input",+        "description": "Interface mode selection bit 1; modes: 0000=SPI, 010X=parallel bus; must be strapped before chip enable."+      },+      {+        "number": "27",+        "name": "MOD[2]",+        "type": "input",+        "description": "Interface mode selection bit 2; modes: 0000=SPI, 010X=parallel bus; must be strapped before chip enable."+      },+      {+        "number": "28",+        "name": "MOD[3]",+        "type": "input",+        "description": "Interface mode selection bit 3; modes: 0000=SPI, 010X=parallel bus; must be strapped before chip enable."+      },+      {+        "number": "29",+        "name": "CSn",+        "type": "input",+        "description": "Chip select input with internal 75kΩ pull-up resistor; low selects W5100S, high deselects."+      },+      {+        "number": "30",+        "name": "SCLK",+        "type": "input",+        "description": "SPI clock input in SPI mode; must be connected to GND or floated in parallel bus mode."+      },+      {+        "number": "31",+        "name": "1V2D",+        "type": "power_in",+        "description": "Digital 1.2V power; supplied from 1V20 voltage source."+      },+      {+        "number": "32",+        "name": "MOSI/ADDR0",+        "type": "input",+        "description": "SPI master output slave input (data input) in SPI mode; address bit 0 in parallel bus mode."+      },+      {+        "number": "33",+        "name": "MISO/ADDR1",+        "type": "bidirectional",+        "description": "SPI master input slave output (data output) in SPI mode; address bit 1 in parallel bus mode."+      },+      {+        "number": "34",+        "name": "RDn",+        "type": "input",+        "description": "Read strobe input with internal 75kΩ pull-up resistor in parallel bus mode; must be connected to 3V3D or floated in SPI mode."+      },+      {+        "number": "35",+        "name": "WRn",+        "type": "input",+        "description": "Write strobe input with internal 75kΩ pull-up resistor in parallel bus mode indicating write operation."+      },+      {+        "number": "36",+        "name": "3V3D",+        "type": "power_in",+        "description": "Digital 3.3V power."+      },+      {+        "number": "37",+        "name": "DAT0",+        "type": "bidirectional",+        "description": "8-bit data bus bit 0; receives or transmits data from/to host in parallel bus mode; must be floated in SPI mode."+      },+      {+        "number": "38",+        "name": "DAT1",+        "type": "bidirectional",+        "description": "8-bit data bus bit 1 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode."+      },+      {+        "number": "39",+        "name": "DAT2",+        "type": "bidirectional",+        "description": "8-bit data bus bit 2 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode."+      },+      {+        "number": "40",+        "name": "DAT3",+        "type": "bidirectional",+        "description": "8-bit data bus bit 3 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode."+      },+      {+        "number": "41",+        "name": "DAT4",+        "type": "bidirectional",+        "description": "8-bit data bus bit 4 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode."+      },+      {+        "number": "42",+        "name": "DAT5",+        "type": "bidirectional",+        "description": "8-bit data bus bit 5 with internal 75kΩ pull-down resistor; receives or transmits data in parallel bus mode; must be floated in SPI mode."+      },+      {+        "number": "43",+        "name": "DAT6",+        "type": "bidirectional",+        "description": "8-bit data bus bit 6; receives or transmits data from/to host in parallel bus mode; must be floated in SPI mode."+      },+      {+        "number": "44",+        "name": "DAT7",+        "type": "bidirectional",+        "description": "8-bit data bus bit 7; receives or transmits data from/to host in parallel bus mode; must be floated in SPI mode."+      },+      {+        "number": "45",+        "name": "1V2D",+        "type": "power_in",+        "description": "Digital 1.2V power; supplied from 1V20 voltage source."+      },+      {+        "number": "46",+        "name": "GND",+        "type": "power_in",+        "description": "Digital ground connection."+      },+      {+        "number": "47",+        "name": "INTn",+        "type": "output",+        "description": "Interrupt output to host; low indicates interrupt occurred, high indicates no interrupt; polarity controlled via MR2[IEN]."+      },+      {+        "number": "48",+        "name": "RSTn",+        "type": "input",+        "description": "Reset input with internal pull-up resistor; must be asserted low for minimum 500ns; W5100S requires 60.3ms initialization after reset release."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 109,+        "cost_usd": 0.9374,+        "at": "2026-09-22T06:41:49"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586185150207680512",+        "pages": 109,+        "sha256": "fca425bbdeeb7ace",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 48,+        "described": 48,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file