← Commit history

Initial commit: component/ucc3818adr

Ray ·87affe106b ·
2 files changed +243
README.mdadded+52
@@ -0,0 +1,52 @@+# UCC3818ADR++**Texas Instruments** · AC-DC Controllers And Regulators · SOIC-16++UCC3818ADR from Texas Instruments, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | GND | power_in | Ground connection; all voltages are measured with respect to ground; bypass VCC and VREF to GND with 0.1µF or larger ceramic capacitor. |+| 2 | PKLMT | input | PFC peak current limit input; threshold for peak limit is 0V; peak current limit reached when PKLMT voltage falls below 0V. |+| 3 | CAOUT | output | Output of wide bandwidth current amplifier that senses line current and commands the PWM to force correct duty cycle; compensation components placed between CAOUT and MOUT. |+| 4 | CAI | input | Current amplifier noninverting input; place resistor between this pin and the GND side of current sense resistor; input remains functional below GND. |+| 5 | MOUT | bidirectional | Output of analog multiplier and inverting input of current amplifier; high-impedance input for differential amplifier configuration; multiplier output current limited to 2×IAC. |+| 6 | IAC | input | Analog multiplier input representing instantaneous rectified line voltage; current proportional to input voltage; recommended maximum current is 500µA. |+| 7 | VAOUT | output | Output of voltage amplifier that regulates output voltage; internally limited to approximately 5.5V to prevent overshoot. |+| 8 | VFF | input | Feed-forward voltage input; RMS voltage signal generated by mirroring 1/2 of IAC into single pole external filter; at low line should be 1.4V. |+| 9 | VREF | power_out | Accurate 7.5V voltage reference output capable of delivering 20mA to peripheral circuitry; internally short-circuit limited; disabled and remains at 0V when VCC below UVLO threshold. |+| 10 | OVP/EN | input | Window comparator input for overvoltage protection and enable function; disables output driver if boost output voltage exceeds programmed level; resets soft-start if pulled below 1.9V typical. |+| 11 | VSENSE | input | Voltage amplifier inverting input; normally connected to compensation network and boost converter output through resistor divider network. |+| 12 | RT | input | Oscillator charging current input; resistor from RT to GND programs oscillator charging current and frequency; TI recommends 10kΩ to 100kΩ; nominal voltage 3V. |+| 13 | SS | input | Soft-start input; external capacitor charged to slowly increase PWM duty cycle during start-up enabling voltage amplifier output to increase gradually; discharged for VCC low conditions. |+| 14 | CT | input | Oscillator timing capacitor input; capacitor from CT to GND sets PWM oscillator frequency; lead should be short and direct to GND. |+| 15 | VCC | power_in | Positive supply voltage input; connect to stable source of at least 20mA from 10V to 17V for normal operation; bypass to GND with 0.1µF or larger ceramic capacitor. |+| 16 | DRVOUT | output | Gate drive output for boost switch; totem-pole MOSFET gate driver with ±1.2A peak current capability; series gate current-limiting resistor recommended to prevent overshoot on capacitive loads. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | SOIC-16 |+| Category | Power Management (PMIC) |+| Pins | 16 |++## CAD (KiCad official)++- Symbol: `UCC3818ADR`+- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`+- 3D model: SOIC-16 (KiCad packages3D, STEP)+- 3D model files: `ucc3818adr-etched.step` / `ucc3818adr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc3818adr.step` / `ucc3818adr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc3818a.pdf) (39 pp, sha256 `bd38dec546e1e7ad`, retrieved 2026-09-23, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ucc3818adr-datasheet.pdf)
page.jsonadded+191
@@ -0,0 +1,191 @@+{+  "slug": "ucc3818adr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments AC-DC Controllers And Regulators, SOIC-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "ucc3818adr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ucc3818adr.kicad_sym",+    "ucc3818adr.kicad_mod",+    "ucc3818adr.glb",+    "ucc3818adr.step",+    "ucc3818adr.lbr",+    "docs/hero.png",+    "docs/ucc3818adr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "UCC3818ADR",+    "manufacturer": "Texas Instruments",+    "package": "SOIC-16",+    "pin_count": 16,+    "category": "Power Management (PMIC)",+    "subcategory": "AC-DC Controllers And Regulators",+    "datasheet": "https://www.ti.com/lit/ds/symlink/ucc3818a.pdf",+    "parts": {+      "symbol": "ucc3818adr.kicad_sym",+      "footprint": "ucc3818adr.kicad_mod",+      "model_3d": "ucc3818adr-etched.glb",+      "model_3d_plain": "ucc3818adr.glb",+      "model_3d_step": "ucc3818adr-etched.step",+      "model_3d_step_plain": "ucc3818adr.step",+      "lbr": "ucc3818adr.lbr"+    },+    "distributor_links": {+      "lcsc": "C783610"+    },+    "pins": [+      {+        "number": "1",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection; all voltages are measured with respect to ground; bypass VCC and VREF to GND with 0.1µF or larger ceramic capacitor."+      },+      {+        "number": "2",+        "name": "PKLMT",+        "type": "input",+        "description": "PFC peak current limit input; threshold for peak limit is 0V; peak current limit reached when PKLMT voltage falls below 0V."+      },+      {+        "number": "3",+        "name": "CAOUT",+        "type": "output",+        "description": "Output of wide bandwidth current amplifier that senses line current and commands the PWM to force correct duty cycle; compensation components placed between CAOUT and MOUT."+      },+      {+        "number": "4",+        "name": "CAI",+        "type": "input",+        "description": "Current amplifier noninverting input; place resistor between this pin and the GND side of current sense resistor; input remains functional below GND."+      },+      {+        "number": "5",+        "name": "MOUT",+        "type": "bidirectional",+        "description": "Output of analog multiplier and inverting input of current amplifier; high-impedance input for differential amplifier configuration; multiplier output current limited to 2×IAC."+      },+      {+        "number": "6",+        "name": "IAC",+        "type": "input",+        "description": "Analog multiplier input representing instantaneous rectified line voltage; current proportional to input voltage; recommended maximum current is 500µA."+      },+      {+        "number": "7",+        "name": "VAOUT",+        "type": "output",+        "description": "Output of voltage amplifier that regulates output voltage; internally limited to approximately 5.5V to prevent overshoot."+      },+      {+        "number": "8",+        "name": "VFF",+        "type": "input",+        "description": "Feed-forward voltage input; RMS voltage signal generated by mirroring 1/2 of IAC into single pole external filter; at low line should be 1.4V."+      },+      {+        "number": "9",+        "name": "VREF",+        "type": "power_out",+        "description": "Accurate 7.5V voltage reference output capable of delivering 20mA to peripheral circuitry; internally short-circuit limited; disabled and remains at 0V when VCC below UVLO threshold."+      },+      {+        "number": "10",+        "name": "OVP/EN",+        "type": "input",+        "description": "Window comparator input for overvoltage protection and enable function; disables output driver if boost output voltage exceeds programmed level; resets soft-start if pulled below 1.9V typical."+      },+      {+        "number": "11",+        "name": "VSENSE",+        "type": "input",+        "description": "Voltage amplifier inverting input; normally connected to compensation network and boost converter output through resistor divider network."+      },+      {+        "number": "12",+        "name": "RT",+        "type": "input",+        "description": "Oscillator charging current input; resistor from RT to GND programs oscillator charging current and frequency; TI recommends 10kΩ to 100kΩ; nominal voltage 3V."+      },+      {+        "number": "13",+        "name": "SS",+        "type": "input",+        "description": "Soft-start input; external capacitor charged to slowly increase PWM duty cycle during start-up enabling voltage amplifier output to increase gradually; discharged for VCC low conditions."+      },+      {+        "number": "14",+        "name": "CT",+        "type": "input",+        "description": "Oscillator timing capacitor input; capacitor from CT to GND sets PWM oscillator frequency; lead should be short and direct to GND."+      },+      {+        "number": "15",+        "name": "VCC",+        "type": "power_in",+        "description": "Positive supply voltage input; connect to stable source of at least 20mA from 10V to 17V for normal operation; bypass to GND with 0.1µF or larger ceramic capacitor."+      },+      {+        "number": "16",+        "name": "DRVOUT",+        "type": "output",+        "description": "Gate drive output for boost switch; totem-pole MOSFET gate driver with ±1.2A peak current capability; series gate current-limiting resistor recommended to prevent overshoot on capacitive loads."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Pin 11 labeled as 'SSENSE' in Pin Configuration table (PAGE 4), but consistently referred to as 'VSE"+        ],+        "pages_sent": 39,+        "cost_usd": 0.4231,+        "at": "2026-09-23T15:06:27"+      },+      "datasheet": {+        "url": "https://www.ti.com/lit/ds/symlink/ucc3818a.pdf",+        "pages": 39,+        "sha256": "bd38dec546e1e7ad",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 16,+        "described": 16,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file