component
UCC2892PW
Public Made by Adomby adom
Texas Instruments AC-DC Controllers And Regulators, TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+52@@ -0,0 +1,52 @@+# UCC2892PW++**Texas Instruments** · AC-DC Controllers And Regulators · TSSOP-16++UCC2892PW from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | RTDEL | input | A resistor from this pin to GND programs the turn-on delay of the two gate drive outputs to accommodate the resonant transitions of the active clamp power converter. |+| 2 | RTON | input | A resistor from this pin to GND programs an internal current source that charges the internal timing capacitor. |+| 3 | RTOFF | input | A resistor from this pin to GND programs an internal current source that discharges the internal timing capacitor. |+| 4 | VREF | power_in | This 5-V reference can supply an external load of up to 5 mA and should be bypassed to AGND as close as possible to the device. |+| 5 | SYNC | input | This unidirectional input synchronizes the internal oscillator, and the synchronizing frequency must be higher than the free-running frequency, with a minimum pulse width of approximately 50 ns. |+| 6 | GND | power_in | This pin is the fundamental analog ground for the PWM control circuitry and should be connected directly to PGND at the device. |+| 7 | CS | input | This pin senses peak current for current-mode control and current limiting, with pulse-by-pulse current limiting activating at approximately 1.27 V for the UCC2892. |+| 8 | RSLOPE | input | A resistor from this pin to GND sets the amplitude of the internal slope compensation current. |+| 9 | FB | input | This pin receives the control voltage from an external optocoupler or error amplifier to set the PWM duty cycle. |+| 10 | SS/SD | input | A capacitor from this pin to GND programs the soft-start interval, is charged by an internal current source of IRTON, and is discharged by a current source equal to IRTON during a fault. |+| 11 | PGND | power_in | This pin is the current return for the high-current output drivers OUT and AUX and should be kept as short as possible on the switching current path. |+| 12 | AUX | output | This output drives the auxiliary clamp MOSFET, turning it on when the main switch turns off, with 2-A source turn-on current and 2-A sink turn-off current. |+| 13 | OUT | output | This output drives the main N-channel MOSFET with 2-A source turn-on current and 2-A sink turn-off current, and a 10-kΩ resistor to PGND is recommended. |+| 14 | VDD | power_in | This is the power supply for the device, which requires a 1-µF capacitor from VDD to PGND with a value at least 10 times greater than the capacitor on VREF. |+| 15 | LINEUV | input | This pin enables and disables the converter by monitoring the bulk input voltage against a 1.27-V threshold, with hysteresis set by an internal current source. |+| 16 | LINEOV | input | For the UCC2892, this pin provides the line overvoltage function, scaling the input voltage to a precise 1.27-V threshold with user-programmable hysteresis. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-16 |+| Category | Power Management (PMIC) |+| Pins | 16 |++## CAD (KiCad official)++- Symbol: `UCC2892PW`+- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`+- 3D model: TSSOP-16 (KiCad packages3D, STEP)+- 3D model files: `ucc2892pw-etched.step` / `ucc2892pw-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc2892pw.step` / `ucc2892pw.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc2892.pdf) (41 pp, sha256 `0b123b68deef52c5`, retrieved 2026-10-08, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ucc2892pw-datasheet.pdf)
page.jsonadded+247@@ -0,0 +1,247 @@+{+ "slug": "ucc2892pw",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments AC-DC Controllers And Regulators, TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "ucc2892pw",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "ucc2892pw.kicad_sym",+ "ucc2892pw.kicad_mod",+ "ucc2892pw.glb",+ "ucc2892pw.step",+ "ucc2892pw.lbr",+ "docs/hero.png",+ "docs/ucc2892pw-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "ucc2892pw-hero.glb",+ "ucc2892pw-hero.overlay.json"+ ],+ "component": {+ "mpn": "UCC2892PW",+ "manufacturer": "Texas Instruments",+ "package": "TSSOP-16",+ "pin_count": 16,+ "category": "Power Management (PMIC)",+ "subcategory": "AC-DC Controllers And Regulators",+ "datasheet": "https://www.ti.com/lit/ds/symlink/ucc2892.pdf",+ "parts": {+ "symbol": "ucc2892pw.kicad_sym",+ "footprint": "ucc2892pw.kicad_mod",+ "model_3d": "ucc2892pw-hero.glb",+ "model_3d_plain": "ucc2892pw.glb",+ "model_3d_step": "ucc2892pw-etched.step",+ "model_3d_step_plain": "ucc2892pw.step",+ "lbr": "ucc2892pw.lbr"+ },+ "distributor_links": {+ "lcsc": "C2869523",+ "digikey": "2156-UCC2892PW-TI-ND",+ "mouser": "595-UCC2892PW"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T16:51:58Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "2156-UCC2892PW-TI-ND",+ "status": "found"+ },+ "mouser": {+ "pn": "595-UCC2892PW",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "RTDEL",+ "type": "input",+ "description": "A resistor from this pin to GND programs the turn-on delay of the two gate drive outputs to accommodate the resonant transitions of the active clamp power converter."+ },+ {+ "number": "2",+ "name": "RTON",+ "type": "input",+ "description": "A resistor from this pin to GND programs an internal current source that charges the internal timing capacitor."+ },+ {+ "number": "3",+ "name": "RTOFF",+ "type": "input",+ "description": "A resistor from this pin to GND programs an internal current source that discharges the internal timing capacitor."+ },+ {+ "number": "4",+ "name": "VREF",+ "type": "power_in",+ "description": "This 5-V reference can supply an external load of up to 5 mA and should be bypassed to AGND as close as possible to the device."+ },+ {+ "number": "5",+ "name": "SYNC",+ "type": "input",+ "description": "This unidirectional input synchronizes the internal oscillator, and the synchronizing frequency must be higher than the free-running frequency, with a minimum pulse width of approximately 50 ns."+ },+ {+ "number": "6",+ "name": "GND",+ "type": "power_in",+ "description": "This pin is the fundamental analog ground for the PWM control circuitry and should be connected directly to PGND at the device."+ },+ {+ "number": "7",+ "name": "CS",+ "type": "input",+ "description": "This pin senses peak current for current-mode control and current limiting, with pulse-by-pulse current limiting activating at approximately 1.27 V for the UCC2892."+ },+ {+ "number": "8",+ "name": "RSLOPE",+ "type": "input",+ "description": "A resistor from this pin to GND sets the amplitude of the internal slope compensation current."+ },+ {+ "number": "9",+ "name": "FB",+ "type": "input",+ "description": "This pin receives the control voltage from an external optocoupler or error amplifier to set the PWM duty cycle."+ },+ {+ "number": "10",+ "name": "SS/SD",+ "type": "input",+ "description": "A capacitor from this pin to GND programs the soft-start interval, is charged by an internal current source of IRTON, and is discharged by a current source equal to IRTON during a fault."+ },+ {+ "number": "11",+ "name": "PGND",+ "type": "power_in",+ "description": "This pin is the current return for the high-current output drivers OUT and AUX and should be kept as short as possible on the switching current path."+ },+ {+ "number": "12",+ "name": "AUX",+ "type": "output",+ "description": "This output drives the auxiliary clamp MOSFET, turning it on when the main switch turns off, with 2-A source turn-on current and 2-A sink turn-off current."+ },+ {+ "number": "13",+ "name": "OUT",+ "type": "output",+ "description": "This output drives the main N-channel MOSFET with 2-A source turn-on current and 2-A sink turn-off current, and a 10-kΩ resistor to PGND is recommended."+ },+ {+ "number": "14",+ "name": "VDD",+ "type": "power_in",+ "description": "This is the power supply for the device, which requires a 1-µF capacitor from VDD to PGND with a value at least 10 times greater than the capacitor on VREF."+ },+ {+ "number": "15",+ "name": "LINEUV",+ "type": "input",+ "description": "This pin enables and disables the converter by monitoring the bulk input voltage against a 1.27-V threshold, with hysteresis set by an internal current source."+ },+ {+ "number": "16",+ "name": "LINEOV",+ "type": "input",+ "description": "For the UCC2892, this pin provides the line overvoltage function, scaling the input voltage to a precise 1.27-V threshold with user-programmable hysteresis."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Pin 16 is LINEOV on the UCC2892 (no VIN pin). The UCC2891/UCC2893 use pin 16 as VIN instead. Pin ass; Only the 16-page excerpt was provided. Pin descriptions are summarized from the terminal functions t"+ ],+ "pages_sent": 16,+ "cost_usd": 0.1048,+ "at": "2026-10-08T16:51:37"+ },+ "datasheet": {+ "url": "https://www.ti.com/lit/ds/symlink/ucc2892.pdf",+ "pages": 41,+ "sha256": "0b123b68deef52c5",+ "source_tier": "mfr"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 16,+ "described": 16,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "ucc2892pw.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "6ad5e98224d02a427d9a6b929a28dbc158b9925fba5adec12db05079f1016948",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "ucc2892pw-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "05a10f91cb051b1c657854e618309aa133c16f321f3a327ff8d316b8795c1a01",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}