← Commit history

Initial commit: component/ucc2891dr

Ray ·29f168ed74 ·
2 files changed +255
README.mdadded+52
@@ -0,0 +1,52 @@+# UCC2891DR++**Texas Instruments** · AC-DC Controllers And Regulators · SOIC-16++UCC2891DR from Texas Instruments, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | RTDEL | input | A resistor from this pin to GND programs the turn-on delay for both gate drive outputs to accommodate the resonant transitions of the active clamp power converter. |+| 2 | RTON | input | A resistor to GND programs an internal current source that charges the internal timing capacitor and is used to set the operating frequency and maximum duty cycle. |+| 3 | RTOFF | input | A resistor to GND programs an internal current source that discharges the internal timing capacitor and is used to set the switching period and maximum duty cycle. |+| 4 | VREF | power_out | Supplies the controller's internal 5-V bias rail as a reference voltage with current-limited output of approximately 5 mA for external circuits. |+| 5 | SYNC | input | Unidirectional synchronization input for the internal oscillator with minimum pulse width of approximately 50 ns and synchronizing frequency higher than the free-running oscillator frequency. |+| 6 | GND | power_in | Provides the reference potential for all small-signal control and programming circuitry inside the device. |+| 7 | CS | input | Direct input to the PWM and current-limit comparators for peak current sensing; threshold is 0.75 V for UCC2891. |+| 8 | RSLOPE | input | A resistor connected from this pin to GND sets the amplitude of the slope compensation current for current-mode control circuitry. |+| 9 | FB | input | Input for the control voltage of the pulse width modulator generated by an external error amplifier; useful voltage range is approximately 1.25 V to 4.5 V. |+| 10 | SS/SD | input | A capacitor from this pin to GND is charged by an internal current source to program the soft-start interval and discharged during fault conditions. |+| 11 | PGND | power_in | Dedicated connection for all high-current circuits including the two high-current gate drivers; requires low-impedance external connection to GND pin. |+| 12 | AUX | output | High-current gate drive output for the auxiliary clamp MOSFET with 2-A source and 2-A sink current capability; active low for P-channel devices. |+| 13 | OUT | output | High-current output driving the main N-channel PWM switching MOSFET with 2-A source and 2-A sink current capability. |+| 14 | VDD | power_in | Power supply for the device biasing the internal gate drivers and 5-V regulator; supply range is 8.5 to 16.0 V with recommended 1-µF bypass capacitor to PGND. |+| 15 | LINEUV | input | Monitors incoming power source to provide accurate undervoltage lockout with programmable hysteresis; threshold voltage is 1.27 V. |+| 16 | VIN | power_in | Connected to the input power rail directly for UCC2891; a high-voltage P-channel JFET startup device provides startup current until bootstrap bias is available, maximum rating 120 V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | SOIC-16 |+| Category | Power Management (PMIC) |+| Pins | 16 |++## CAD (KiCad official)++- Symbol: `UCC2891DR`+- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`+- 3D model: SOIC-16 (KiCad packages3D, STEP)+- 3D model files: `ucc2891dr-etched.step` / `ucc2891dr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc2891dr.step` / `ucc2891dr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/ucc2891.pdf) (41 pp, sha256 `0b123b68deef52c5`, retrieved 2026-09-26, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ucc2891dr-datasheet.pdf)
page.jsonadded+203
@@ -0,0 +1,203 @@+{+  "slug": "ucc2891dr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments AC-DC Controllers And Regulators, SOIC-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "ucc2891dr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ucc2891dr.kicad_sym",+    "ucc2891dr.kicad_mod",+    "ucc2891dr.glb",+    "ucc2891dr.step",+    "ucc2891dr.lbr",+    "docs/hero.png",+    "docs/ucc2891dr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "UCC2891DR",+    "manufacturer": "Texas Instruments",+    "package": "SOIC-16",+    "pin_count": 16,+    "category": "Power Management (PMIC)",+    "subcategory": "AC-DC Controllers And Regulators",+    "datasheet": "https://www.ti.com/lit/ds/symlink/ucc2891.pdf",+    "parts": {+      "symbol": "ucc2891dr.kicad_sym",+      "footprint": "ucc2891dr.kicad_mod",+      "model_3d": "ucc2891dr-etched.glb",+      "model_3d_plain": "ucc2891dr.glb",+      "model_3d_step": "ucc2891dr-etched.step",+      "model_3d_step_plain": "ucc2891dr.step",+      "lbr": "ucc2891dr.lbr"+    },+    "distributor_links": {+      "lcsc": "C1848490",+      "digikey": "296-UCC2891DRTR-ND",+      "mouser": "595-UCC2891DR"+    },+    "distributor_check": {+      "checked_at": "2026-09-26T22:48:53Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-UCC2891DRTR-ND",+        "status": "found"+      },+      "mouser": {+        "pn": "595-UCC2891DR",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "RTDEL",+        "type": "input",+        "description": "A resistor from this pin to GND programs the turn-on delay for both gate drive outputs to accommodate the resonant transitions of the active clamp power converter."+      },+      {+        "number": "2",+        "name": "RTON",+        "type": "input",+        "description": "A resistor to GND programs an internal current source that charges the internal timing capacitor and is used to set the operating frequency and maximum duty cycle."+      },+      {+        "number": "3",+        "name": "RTOFF",+        "type": "input",+        "description": "A resistor to GND programs an internal current source that discharges the internal timing capacitor and is used to set the switching period and maximum duty cycle."+      },+      {+        "number": "4",+        "name": "VREF",+        "type": "power_out",+        "description": "Supplies the controller's internal 5-V bias rail as a reference voltage with current-limited output of approximately 5 mA for external circuits."+      },+      {+        "number": "5",+        "name": "SYNC",+        "type": "input",+        "description": "Unidirectional synchronization input for the internal oscillator with minimum pulse width of approximately 50 ns and synchronizing frequency higher than the free-running oscillator frequency."+      },+      {+        "number": "6",+        "name": "GND",+        "type": "power_in",+        "description": "Provides the reference potential for all small-signal control and programming circuitry inside the device."+      },+      {+        "number": "7",+        "name": "CS",+        "type": "input",+        "description": "Direct input to the PWM and current-limit comparators for peak current sensing; threshold is 0.75 V for UCC2891."+      },+      {+        "number": "8",+        "name": "RSLOPE",+        "type": "input",+        "description": "A resistor connected from this pin to GND sets the amplitude of the slope compensation current for current-mode control circuitry."+      },+      {+        "number": "9",+        "name": "FB",+        "type": "input",+        "description": "Input for the control voltage of the pulse width modulator generated by an external error amplifier; useful voltage range is approximately 1.25 V to 4.5 V."+      },+      {+        "number": "10",+        "name": "SS/SD",+        "type": "input",+        "description": "A capacitor from this pin to GND is charged by an internal current source to program the soft-start interval and discharged during fault conditions."+      },+      {+        "number": "11",+        "name": "PGND",+        "type": "power_in",+        "description": "Dedicated connection for all high-current circuits including the two high-current gate drivers; requires low-impedance external connection to GND pin."+      },+      {+        "number": "12",+        "name": "AUX",+        "type": "output",+        "description": "High-current gate drive output for the auxiliary clamp MOSFET with 2-A source and 2-A sink current capability; active low for P-channel devices."+      },+      {+        "number": "13",+        "name": "OUT",+        "type": "output",+        "description": "High-current output driving the main N-channel PWM switching MOSFET with 2-A source and 2-A sink current capability."+      },+      {+        "number": "14",+        "name": "VDD",+        "type": "power_in",+        "description": "Power supply for the device biasing the internal gate drivers and 5-V regulator; supply range is 8.5 to 16.0 V with recommended 1-µF bypass capacitor to PGND."+      },+      {+        "number": "15",+        "name": "LINEUV",+        "type": "input",+        "description": "Monitors incoming power source to provide accurate undervoltage lockout with programmable hysteresis; threshold voltage is 1.27 V."+      },+      {+        "number": "16",+        "name": "VIN",+        "type": "power_in",+        "description": "Connected to the input power rail directly for UCC2891; a high-voltage P-channel JFET startup device provides startup current until bootstrap bias is available, maximum rating 120 V."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 41,+        "cost_usd": 0.3968,+        "at": "2026-09-26T22:48:34"+      },+      "datasheet": {+        "url": "https://www.ti.com/lit/ds/symlink/ucc2891.pdf",+        "pages": 41,+        "sha256": "0b123b68deef52c5",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 16,+        "described": 16,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file