component
UCC2813QDR-1Q1
Public Made by Adomby adom
Texas Instruments AC-DC Controllers And Regulators, SOIC-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+45@@ -0,0 +1,45 @@+# UCC2813QDR-1Q1++**Texas Instruments** · AC-DC Controllers And Regulators · SOIC-8++UCC2813QDR-1Q1 from Texas Instruments, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | COMP | output | COMP is the error amplifier output and the PWM comparator input, with feedback loop compensation applied between this pin and FB. |+| 2 | FB | input | FB is the inverting input of the error amplifier, and its lead length and stray capacitance should be kept as small as possible for best stability. |+| 3 | CS | input | CS is the input to the current-sense comparators (PWM and overcurrent), with 100 ns leading-edge blanking and an overcurrent threshold of 1.32 V to 1.7 V (1.55 V typical). |+| 4 | RC | input | RC is the oscillator timing pin, where an external resistor from REF and a capacitor to GND set the switching frequency (up to 1 MHz) and maximum duty cycle, with timing resistor limited to 10 kΩ to 200 kΩ and never below 10 kΩ. |+| 5 | GND | power_in | GND is the reference ground and power ground for all functions of the device, and TI recommends separating the signal return from the high-current gate driver path. |+| 6 | OUT | output | OUT is the high-current power driver output for the power MOSFET gate, rated at 1 A peak (±1 A absolute maximum) and held low during UVLO. |+| 7 | VCC | power_in | VCC is the device bias supply input, which must be kept below the 12 V absolute maximum (internal zener clamps near 13.5 V) and driven through a current-limiting resistor, with a 0.1 µF ceramic bypass to GND placed close to the pin. |+| 8 | REF | power_out | REF is the voltage reference output (5 V for the -1 variant), limited to 5 mA output current and requiring at least a 0.1 µF ceramic bypass to GND placed close to the pin. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | SOIC-8 |+| Category | Power Management (PMIC) |+| Pins | 8 |++## CAD (KiCad official)++- Symbol: `UCC2813QDR-1Q1`+- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`+- 3D model: SOIC-8 (KiCad packages3D, STEP)+- 3D model files: `ucc2813qdr-1q1-etched.step` / `ucc2813qdr-1q1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ucc2813qdr-1q1.step` / `ucc2813qdr-1q1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/ucc2813-0-q1) (47 pp, sha256 `114dd59e68535e9e`, retrieved 2026-10-08, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ucc2813qdr-1q1-datasheet.pdf)
page.jsonadded+199@@ -0,0 +1,199 @@+{+ "slug": "ucc2813qdr-1q1",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments AC-DC Controllers And Regulators, SOIC-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "ucc2813qdr-1q1",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "ucc2813qdr-1q1.kicad_sym",+ "ucc2813qdr-1q1.kicad_mod",+ "ucc2813qdr-1q1.glb",+ "ucc2813qdr-1q1.step",+ "ucc2813qdr-1q1.lbr",+ "docs/hero.png",+ "docs/ucc2813qdr-1q1-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "ucc2813qdr-1q1-hero.glb",+ "ucc2813qdr-1q1-hero.overlay.json"+ ],+ "component": {+ "mpn": "UCC2813QDR-1Q1",+ "manufacturer": "Texas Instruments",+ "package": "SOIC-8",+ "pin_count": 8,+ "category": "Power Management (PMIC)",+ "subcategory": "AC-DC Controllers And Regulators",+ "datasheet": "https://www.ti.com/cn/lit/gpn/ucc2813-0-q1",+ "parts": {+ "symbol": "ucc2813qdr-1q1.kicad_sym",+ "footprint": "ucc2813qdr-1q1.kicad_mod",+ "model_3d": "ucc2813qdr-1q1-hero.glb",+ "model_3d_plain": "ucc2813qdr-1q1.glb",+ "model_3d_step": "ucc2813qdr-1q1-etched.step",+ "model_3d_step_plain": "ucc2813qdr-1q1.step",+ "lbr": "ucc2813qdr-1q1.lbr"+ },+ "distributor_links": {+ "lcsc": "C2657963",+ "digikey": "296-19428-2-ND",+ "mouser": "595-UCC2813QDR-1Q1"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T01:38:12Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-19428-2-ND",+ "status": "found"+ },+ "mouser": {+ "pn": "595-UCC2813QDR-1Q1",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "COMP",+ "type": "output",+ "description": "COMP is the error amplifier output and the PWM comparator input, with feedback loop compensation applied between this pin and FB."+ },+ {+ "number": "2",+ "name": "FB",+ "type": "input",+ "description": "FB is the inverting input of the error amplifier, and its lead length and stray capacitance should be kept as small as possible for best stability."+ },+ {+ "number": "3",+ "name": "CS",+ "type": "input",+ "description": "CS is the input to the current-sense comparators (PWM and overcurrent), with 100 ns leading-edge blanking and an overcurrent threshold of 1.32 V to 1.7 V (1.55 V typical)."+ },+ {+ "number": "4",+ "name": "RC",+ "type": "input",+ "description": "RC is the oscillator timing pin, where an external resistor from REF and a capacitor to GND set the switching frequency (up to 1 MHz) and maximum duty cycle, with timing resistor limited to 10 kΩ to 200 kΩ and never below 10 kΩ."+ },+ {+ "number": "5",+ "name": "GND",+ "type": "power_in",+ "description": "GND is the reference ground and power ground for all functions of the device, and TI recommends separating the signal return from the high-current gate driver path."+ },+ {+ "number": "6",+ "name": "OUT",+ "type": "output",+ "description": "OUT is the high-current power driver output for the power MOSFET gate, rated at 1 A peak (±1 A absolute maximum) and held low during UVLO."+ },+ {+ "number": "7",+ "name": "VCC",+ "type": "power_in",+ "description": "VCC is the device bias supply input, which must be kept below the 12 V absolute maximum (internal zener clamps near 13.5 V) and driven through a current-limiting resistor, with a 0.1 µF ceramic bypass to GND placed close to the pin."+ },+ {+ "number": "8",+ "name": "REF",+ "type": "power_out",+ "description": "REF is the voltage reference output (5 V for the -1 variant), limited to 5 mA output current and requiring at least a 0.1 µF ceramic bypass to GND placed close to the pin."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Ordering table (page 37) lists UCC2813QDR-1Q1 with status NRND (Not Recommended for New Designs). Co; Pin numbers and names are from Table 5-1 and the SOIC/PDIP top-view figure (Figure 5-1, labeled N an; Pin types are KiCad mappings: the datasheet labels VCC as I and REF as O. VCC was mapped to power_in"+ ],+ "pages_sent": 35,+ "cost_usd": 0.1896,+ "at": "2026-10-08T01:37:56"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/ucc2813-0-q1",+ "pages": 47,+ "sha256": "114dd59e68535e9e",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 8,+ "described": 8,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "ucc2813qdr-1q1.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6,+ 4.9,+ 1.75+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "07f46cff378d30e6c27dfd5a03092c795323f86d91c71fc7e743f4f418dc553a",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "ucc2813qdr-1q1-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6,+ 4.9,+ 1.75+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "cac67d9c00aa9bb9b7458e8f10e2af8b8b20203c19885d9930b809061ea98d9f",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}