component
TUSB1106RGTR
Public Made by Adomby adom
Texas Instruments USB Converters, HVQFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+53@@ -0,0 +1,53 @@+# TUSB1106RGTR++**Texas Instruments** · USB Converters · HVQFN-16-EP(3x3)++TUSB1106RGTR from Texas Instruments, in a HVQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OE | input | Active-LOW output enable (CMOS level with respect to VCC(I/O)) that enables the transceiver to transmit data on the USB bus. |+| 2 | RCV | output | Differential data receiver output (CMOS level with respect to VCC(I/O), push-pull, 4-mA drive); driven LOW when SUSPND is HIGH and stable during SE0. |+| 3 | VP | output | Single-ended D+ receiver output (CMOS level with respect to VCC(I/O), push-pull, 4-mA drive); driven HIGH when no supply is connected to VCC(5.0) and Vreg(3.3). |+| 4 | VM | output | Single-ended D- receiver output (CMOS level with respect to VCC(I/O), push-pull, 4-mA drive); driven HIGH when no supply is connected to VCC(5.0) and Vreg(3.3). |+| 5 | SUSPND | input | Suspend input (CMOS level with respect to VCC(I/O)); HIGH enables the low-power state while the USB bus is inactive and drives RCV LOW. |+| 6 | GND | power_in | Ground supply pin on the TUSB1106 RGT package. |+| 7 | VCC(I/O) | power_in | Digital I/O supply voltage of 1.65 to 3.6 V, independent of VCC(5.0) and Vreg(3.3) and must never exceed Vreg(3.3); D+ and D- are 3-state when it is not connected. |+| 8 | SPEED | input | Speed selection input (CMOS level with respect to VCC(I/O)) that sets the D+/D- slew rate: LOW is low speed (1.5 Mbit/s), HIGH is full speed (12 Mbit/s). |+| 9 | D- | bidirectional | Negative USB data bus connection (analog, differential); for low-speed mode connect to Vpu(3.3) via a 1.5-kOhm resistor. |+| 10 | D+ | bidirectional | Positive USB data bus connection (analog, differential); for full-speed mode connect to Vpu(3.3) via a 1.5-kOhm resistor. |+| 11 | VPO | input | Driver data input (CMOS level with respect to VCC(I/O), Schmitt trigger) for the differential input data interface. |+| 12 | VMO | input | Driver data input (CMOS level with respect to VCC(I/O), Schmitt trigger) for the differential input data interface. |+| 13 | Vreg(3.3) | power_out | Regulated 3 V to 3.6 V output during 5-V operation, needs a decoupling capacitor of at least 0.1 uF, and is the supply input for 3.3 V ±10% operation. |+| 14 | VCC(5.0) | power_in | Internal regulator supply input of 4 V to 5.5 V, which can connect directly to USB VBUS; connect to Vreg(3.3) for the regulator bypass option. |+| 15 | Vpu(3.3) | power_out | Pullup supply voltage (3.3 V ±10%) for the external 1.5-kOhm resistor on D+ or D-; high impedance when SOFTCON is LOW, connected internally to Vreg(3.3) when SOFTCON is HIGH. |+| 16 | SOFTCON | input | Software-controlled USB connection input; HIGH applies 3.3 V to Vpu(3.3) for the external 1.5-kOhm pullup, allowing software connect/disconnect signaling. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HVQFN-16-EP(3x3) |+| Category | Interface |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `TUSB1106RGTR`+- Footprint: `Package_DFN_QFN:HVQFN-16-1EP_3x3mm_P0.5mm_EP1.5x1.5mm`+- 3D model: HVQFN-16-EP(3x3) (KiCad packages3D, STEP)+- 3D model files: `tusb1106rgtr-etched.step` / `tusb1106rgtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tusb1106rgtr.step` / `tusb1106rgtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tusb1106.pdf) (36 pp, sha256 `82d46206cda20726`, retrieved 2026-10-08, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tusb1106rgtr-datasheet.pdf)
page.jsonadded+256@@ -0,0 +1,256 @@+{+ "slug": "tusb1106rgtr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments USB Converters, HVQFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "interface",+ "tusb1106rgtr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tusb1106rgtr.kicad_sym",+ "tusb1106rgtr.kicad_mod",+ "tusb1106rgtr.glb",+ "tusb1106rgtr.step",+ "tusb1106rgtr.lbr",+ "docs/hero.png",+ "docs/tusb1106rgtr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tusb1106rgtr-hero.glb",+ "tusb1106rgtr-hero.overlay.json"+ ],+ "component": {+ "mpn": "TUSB1106RGTR",+ "manufacturer": "Texas Instruments",+ "package": "HVQFN-16-EP(3x3)",+ "pin_count": 17,+ "category": "Interface",+ "subcategory": "USB Converters",+ "datasheet": "https://www.ti.com/lit/ds/symlink/tusb1106.pdf",+ "parts": {+ "symbol": "tusb1106rgtr.kicad_sym",+ "footprint": "tusb1106rgtr.kicad_mod",+ "model_3d": "tusb1106rgtr-hero.glb",+ "model_3d_plain": "tusb1106rgtr.glb",+ "model_3d_step": "tusb1106rgtr-etched.step",+ "model_3d_step_plain": "tusb1106rgtr.step",+ "lbr": "tusb1106rgtr.lbr"+ },+ "distributor_links": {+ "lcsc": "C2671295",+ "digikey": "296-21924-2-ND",+ "mouser": "595-TUSB1106RGTR"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T16:00:20Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-21924-2-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TUSB1106RGTR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "OE",+ "type": "input",+ "description": "Active-LOW output enable (CMOS level with respect to VCC(I/O)) that enables the transceiver to transmit data on the USB bus."+ },+ {+ "number": "2",+ "name": "RCV",+ "type": "output",+ "description": "Differential data receiver output (CMOS level with respect to VCC(I/O), push-pull, 4-mA drive); driven LOW when SUSPND is HIGH and stable during SE0."+ },+ {+ "number": "3",+ "name": "VP",+ "type": "output",+ "description": "Single-ended D+ receiver output (CMOS level with respect to VCC(I/O), push-pull, 4-mA drive); driven HIGH when no supply is connected to VCC(5.0) and Vreg(3.3)."+ },+ {+ "number": "4",+ "name": "VM",+ "type": "output",+ "description": "Single-ended D- receiver output (CMOS level with respect to VCC(I/O), push-pull, 4-mA drive); driven HIGH when no supply is connected to VCC(5.0) and Vreg(3.3)."+ },+ {+ "number": "5",+ "name": "SUSPND",+ "type": "input",+ "description": "Suspend input (CMOS level with respect to VCC(I/O)); HIGH enables the low-power state while the USB bus is inactive and drives RCV LOW."+ },+ {+ "number": "6",+ "name": "GND",+ "type": "power_in",+ "description": "Ground supply pin on the TUSB1106 RGT package."+ },+ {+ "number": "7",+ "name": "VCC(I/O)",+ "type": "power_in",+ "description": "Digital I/O supply voltage of 1.65 to 3.6 V, independent of VCC(5.0) and Vreg(3.3) and must never exceed Vreg(3.3); D+ and D- are 3-state when it is not connected."+ },+ {+ "number": "8",+ "name": "SPEED",+ "type": "input",+ "description": "Speed selection input (CMOS level with respect to VCC(I/O)) that sets the D+/D- slew rate: LOW is low speed (1.5 Mbit/s), HIGH is full speed (12 Mbit/s)."+ },+ {+ "number": "9",+ "name": "D-",+ "type": "bidirectional",+ "description": "Negative USB data bus connection (analog, differential); for low-speed mode connect to Vpu(3.3) via a 1.5-kOhm resistor."+ },+ {+ "number": "10",+ "name": "D+",+ "type": "bidirectional",+ "description": "Positive USB data bus connection (analog, differential); for full-speed mode connect to Vpu(3.3) via a 1.5-kOhm resistor."+ },+ {+ "number": "11",+ "name": "VPO",+ "type": "input",+ "description": "Driver data input (CMOS level with respect to VCC(I/O), Schmitt trigger) for the differential input data interface."+ },+ {+ "number": "12",+ "name": "VMO",+ "type": "input",+ "description": "Driver data input (CMOS level with respect to VCC(I/O), Schmitt trigger) for the differential input data interface."+ },+ {+ "number": "13",+ "name": "Vreg(3.3)",+ "type": "power_out",+ "description": "Regulated 3 V to 3.6 V output during 5-V operation, needs a decoupling capacitor of at least 0.1 uF, and is the supply input for 3.3 V ±10% operation."+ },+ {+ "number": "14",+ "name": "VCC(5.0)",+ "type": "power_in",+ "description": "Internal regulator supply input of 4 V to 5.5 V, which can connect directly to USB VBUS; connect to Vreg(3.3) for the regulator bypass option."+ },+ {+ "number": "15",+ "name": "Vpu(3.3)",+ "type": "power_out",+ "description": "Pullup supply voltage (3.3 V ±10%) for the external 1.5-kOhm resistor on D+ or D-; high impedance when SOFTCON is LOW, connected internally to Vreg(3.3) when SOFTCON is HIGH."+ },+ {+ "number": "16",+ "name": "SOFTCON",+ "type": "input",+ "description": "Software-controlled USB connection input; HIGH applies 3.3 V to Vpu(3.3) for the external 1.5-kOhm pullup, allowing software connect/disconnect signaling."+ },+ {+ "number": "17",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-sonnet-5-5",+ "primary_mode": "text+vision",+ "consensus_model": "claude-opus-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The TUSB1106 RGT exposed die pad (pin 17) is drawn as 'No Connect', and the datasheet says the die p; The datasheet lists the RGT footprint as 3x3 mm, but the ordering table calls it VQFN rather than HV",+ "exposed pad 17 added from the footprint",+ "vision extraction: provenance cannot be text-verified; needs consensus"+ ],+ "pages_sent": 36,+ "cost_usd": 0.3214,+ "at": "2026-10-08T15:59:59"+ },+ "datasheet": {+ "url": "https://www.ti.com/lit/ds/symlink/tusb1106.pdf",+ "pages": 36,+ "sha256": "82d46206cda20726",+ "source_tier": "mfr"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 17,+ "described": 17,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tusb1106rgtr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 3,+ 0.77+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "b32e528bf0799efacfbfd0e6175a168fff91b5905ee4d3720cfee9527a156853",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tusb1106rgtr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 3,+ 0.77+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "2805d3592632ad6f637c2f9ff8525b5222696d9b73cffce9dce734535526eb1a",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}