component
TPS92515QDGQTQ1
Public Made by Adomby adom
Texas Instruments LED Drivers, MSOP-10-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+48@@ -0,0 +1,48 @@+# TPS92515QDGQTQ1++**Texas Instruments** · LED Drivers · MSOP-10-EP++TPS92515QDGQTQ1 from Texas Instruments, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | COFF | input | Connect a resistor from VOUT and a capacitor to GND to set the OFF-time. |+| 2 | VCC | power_out | 5-V regulator output; use a decoupling capacitor from VCC to ground (see the VCC capacitor selection section). |+| 3 | GND | power_in | Ground. |+| 4 | BOOT | input | Connect a ceramic capacitor between BOOT and SW and a diode from VCC to BOOT to power the high-side FET drive circuitry. |+| 5 | SW | output | Internal FET source; connect to the output inductor. |+| 6 | DRN | input | Internal FET drain; connect to the CSN node. |+| 7 | CSN | input | Current sense negative input; connect the current sense resistor from VIN to CSN for high-side current sense control. |+| 8 | VIN | power_in | Connect to input voltage (recommended operating VIN is 5.5 V to 42 V for TPS92515x and 5.5 V to 65 V for TPS92515HVx); VIN is also the current sense positive input. |+| 9 | PWM | input | PWM dimming input; output current is PWM dimmed from the maximum analog controlled level, and it should be connected to VCC if not used. |+| 10 | IADJ | input | Output current adjust; connect to an external divider or reference, or tie to VCC, with the internal clamp at 2.4 V. |+| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | MSOP-10-EP |+| Category | LED Drivers |+| Pins | 11 |++## CAD (KiCad official)++- Symbol: `TPS92515QDGQTQ1`+- Footprint: `Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm`+- 3D model: MSOP-10-EP (KiCad packages3D, STEP)+- 3D model files: `tps92515qdgqtq1-etched.step` / `tps92515qdgqtq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps92515qdgqtq1.step` / `tps92515qdgqtq1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps92515-q1) (41 pp, sha256 `b6e415ec88013b0b`, retrieved 2026-10-08, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps92515qdgqtq1-datasheet.pdf)
page.jsonadded+219@@ -0,0 +1,219 @@+{+ "slug": "tps92515qdgqtq1",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments LED Drivers, MSOP-10-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "led drivers",+ "tps92515qdgqtq1",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps92515qdgqtq1.kicad_sym",+ "tps92515qdgqtq1.kicad_mod",+ "tps92515qdgqtq1.glb",+ "tps92515qdgqtq1.step",+ "tps92515qdgqtq1.lbr",+ "docs/hero.png",+ "docs/tps92515qdgqtq1-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps92515qdgqtq1-hero.glb",+ "tps92515qdgqtq1-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS92515QDGQTQ1",+ "manufacturer": "Texas Instruments",+ "package": "MSOP-10-EP",+ "pin_count": 11,+ "category": "LED Drivers",+ "subcategory": "LED Drivers",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps92515-q1",+ "parts": {+ "symbol": "tps92515qdgqtq1.kicad_sym",+ "footprint": "tps92515qdgqtq1.kicad_mod",+ "model_3d": "tps92515qdgqtq1-hero.glb",+ "model_3d_plain": "tps92515qdgqtq1.glb",+ "model_3d_step": "tps92515qdgqtq1-etched.step",+ "model_3d_step_plain": "tps92515qdgqtq1.step",+ "lbr": "tps92515qdgqtq1.lbr"+ },+ "distributor_links": {+ "lcsc": "C213557",+ "digikey": "296-44741-2-ND",+ "mouser": "595-TPS92515QDGQTQ1"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T18:26:26Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-44741-2-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS92515QDGQTQ1",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "COFF",+ "type": "input",+ "description": "Connect a resistor from VOUT and a capacitor to GND to set the OFF-time."+ },+ {+ "number": "2",+ "name": "VCC",+ "type": "power_out",+ "description": "5-V regulator output; use a decoupling capacitor from VCC to ground (see the VCC capacitor selection section)."+ },+ {+ "number": "3",+ "name": "GND",+ "type": "power_in",+ "description": "Ground."+ },+ {+ "number": "4",+ "name": "BOOT",+ "type": "input",+ "description": "Connect a ceramic capacitor between BOOT and SW and a diode from VCC to BOOT to power the high-side FET drive circuitry."+ },+ {+ "number": "5",+ "name": "SW",+ "type": "output",+ "description": "Internal FET source; connect to the output inductor."+ },+ {+ "number": "6",+ "name": "DRN",+ "type": "input",+ "description": "Internal FET drain; connect to the CSN node."+ },+ {+ "number": "7",+ "name": "CSN",+ "type": "input",+ "description": "Current sense negative input; connect the current sense resistor from VIN to CSN for high-side current sense control."+ },+ {+ "number": "8",+ "name": "VIN",+ "type": "power_in",+ "description": "Connect to input voltage (recommended operating VIN is 5.5 V to 42 V for TPS92515x and 5.5 V to 65 V for TPS92515HVx); VIN is also the current sense positive input."+ },+ {+ "number": "9",+ "name": "PWM",+ "type": "input",+ "description": "PWM dimming input; output current is PWM dimmed from the maximum analog controlled level, and it should be connected to VCC if not used."+ },+ {+ "number": "10",+ "name": "IADJ",+ "type": "input",+ "description": "Output current adjust; connect to an external divider or reference, or tie to VCC, with the internal clamp at 2.4 V."+ },+ {+ "number": "11",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The thermal pad (labelled PAD on the drawing) is not a numbered pin in the datasheet, so it is not l; The pin table is shared by the whole TPS92515 family (TPS92515, -Q1, HV, HV-Q1) and the DGQ package.; Pin 1 description refers to 'VOUT', which does not appear as a pin name in the pin table. It is copi",+ "exposed pad 11 added from the footprint"+ ],+ "pages_sent": 12,+ "cost_usd": 0.076,+ "at": "2026-10-08T18:26:06"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps92515-q1",+ "pages": 41,+ "sha256": "b6e415ec88013b0b",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 11,+ "described": 11,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps92515qdgqtq1.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 0.95+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "18605eed706df7bb9674107abe7aa36e0ba163a09c21a2cee6c75cfa291b7937",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps92515qdgqtq1-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 0.95+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "da89c512626fd9849b2e7ed3aefec14f87ccae7254586efae16194f493704fa5",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}