component
TPS7A1601ADGNR
Public Made by Adomby adom
Texas Instruments Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, HVSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+45@@ -0,0 +1,45 @@+# TPS7A1601ADGNR++**Texas Instruments** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · HVSSOP-8++TPS7A1601ADGNR from Texas Instruments, in a HVSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OUT | power_out | Regulator output pin; a capacitor greater than 2.2 µF must be tied from this pin to ground for stability, and a 10-µF ceramic capacitor is recommended as close to the device as possible. |+| 2 | FB/DNC | input | For the adjustable version this is the feedback input to the control-loop error amplifier that sets the output voltage through external resistors; do not route this pin to any net, including GND or IN, on fixed-voltage versions. |+| 3 | PG | output | Open-collector, active-high power-good output with a user-programmable delay; leave open or connect to GND if the power-good function is not needed. |+| 4 | GND | power_in | Ground pin. |+| 5 | EN | input | Enable pin that turns the regulator on when VEN is at or above VEN_HI and off when VEN is at or below VEN_LO; it may be tied to IN if unused, and VEN must remain at or below VIN at all times. |+| 6 | NC | unconnected | No internal connection; this pin can be left open or tied to any voltage between GND and IN. |+| 7 | DELAY | output | Delay pin for the PG delay time; connect a capacitor to GND to set the delay, or leave open if the reset function is not needed, with DELAY pin voltage specified from 0 V to 5 V. |+| 8 | IN | power_in | Regulator input supply pin, operating from 3 V to 60 V; a capacitor greater than 0.1 µF must be tied from this pin to ground for stability, and a 10-µF ceramic capacitor is recommended close to the device. |+| 9 | Thermal pad | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HVSSOP-8 |+| Category | Power Management (PMIC) |+| Pins | 9 |++## CAD (KiCad official)++- Symbol: `TPS7A1601ADGNR`+- Footprint: `Package_SO:HVSSOP-8-1EP_3x3mm_P0.65mm_EP1.57x1.89mm`+- 3D model: HVSSOP-8, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.0 mm nominal HVSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)+- 3D model files: `tps7a1601adgnr-etched.step` / `tps7a1601adgnr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps7a1601adgnr.step` / `tps7a1601adgnr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603074549911478272) (25 pp, sha256 `28655df2042aed38`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps7a1601adgnr-datasheet.pdf)
page.jsonadded+207@@ -0,0 +1,207 @@+{+ "slug": "tps7a1601adgnr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, HVSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "tps7a1601adgnr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps7a1601adgnr.kicad_sym",+ "tps7a1601adgnr.kicad_mod",+ "tps7a1601adgnr.glb",+ "tps7a1601adgnr.step",+ "tps7a1601adgnr.lbr",+ "docs/hero.png",+ "docs/tps7a1601adgnr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps7a1601adgnr-hero.glb",+ "tps7a1601adgnr-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS7A1601ADGNR",+ "manufacturer": "Texas Instruments",+ "package": "HVSSOP-8",+ "pin_count": 9,+ "category": "Power Management (PMIC)",+ "subcategory": "Voltage Regulators - Linear, Low Drop Out (LDO) Regulators",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603074549911478272",+ "parts": {+ "symbol": "tps7a1601adgnr.kicad_sym",+ "footprint": "tps7a1601adgnr.kicad_mod",+ "model_3d": "tps7a1601adgnr-hero.glb",+ "model_3d_plain": "tps7a1601adgnr.glb",+ "model_3d_step": "tps7a1601adgnr-etched.step",+ "model_3d_step_plain": "tps7a1601adgnr.step",+ "lbr": "tps7a1601adgnr.lbr"+ },+ "distributor_links": {+ "lcsc": "C6886485",+ "digikey": "296-TPS7A1601ADGNRTR-ND",+ "mouser": "595-TPS7A1601ADGNR"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T20:25:57Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-TPS7A1601ADGNRTR-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS7A1601ADGNR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "OUT",+ "type": "power_out",+ "description": "Regulator output pin; a capacitor greater than 2.2 µF must be tied from this pin to ground for stability, and a 10-µF ceramic capacitor is recommended as close to the device as possible."+ },+ {+ "number": "2",+ "name": "FB/DNC",+ "type": "input",+ "description": "For the adjustable version this is the feedback input to the control-loop error amplifier that sets the output voltage through external resistors; do not route this pin to any net, including GND or IN, on fixed-voltage versions."+ },+ {+ "number": "3",+ "name": "PG",+ "type": "output",+ "description": "Open-collector, active-high power-good output with a user-programmable delay; leave open or connect to GND if the power-good function is not needed."+ },+ {+ "number": "4",+ "name": "GND",+ "type": "power_in",+ "description": "Ground pin."+ },+ {+ "number": "5",+ "name": "EN",+ "type": "input",+ "description": "Enable pin that turns the regulator on when VEN is at or above VEN_HI and off when VEN is at or below VEN_LO; it may be tied to IN if unused, and VEN must remain at or below VIN at all times."+ },+ {+ "number": "6",+ "name": "NC",+ "type": "unconnected",+ "description": "No internal connection; this pin can be left open or tied to any voltage between GND and IN."+ },+ {+ "number": "7",+ "name": "DELAY",+ "type": "output",+ "description": "Delay pin for the PG delay time; connect a capacitor to GND to set the delay, or leave open if the reset function is not needed, with DELAY pin voltage specified from 0 V to 5 V."+ },+ {+ "number": "8",+ "name": "IN",+ "type": "power_in",+ "description": "Regulator input supply pin, operating from 3 V to 60 V; a capacitor greater than 0.1 µF must be tied from this pin to ground for stability, and a 10-µF ceramic capacitor is recommended close to the device."+ },+ {+ "number": "9",+ "name": "Thermal pad",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The thermal pad is listed in Table 5-1 as 'Pad' with no pin number, so it is not included in the pin; The datasheet covers the TPS7A16A family. The TPS7A1601A ordering code (adjustable, DGN, reel) is in",+ "exposed pad 9 added from the footprint"+ ],+ "pages_sent": 8,+ "cost_usd": 0.05,+ "at": "2026-10-08T20:24:56"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603074549911478272",+ "pages": 25,+ "sha256": "28655df2042aed38",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 9,+ "described": 9,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps7a1601adgnr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.91,+ 3,+ 1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "be174a651861e764994f8be73d5e3ebcda500c1061a60fae9d8182b378444076",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps7a1601adgnr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.91,+ 3,+ 1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "5bf7d1fc4d1bbd47f94621da3867f7a3b3401c31f2cce905046afca5e0df60c5",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}