component
TPS62093RGTR
Public Made by Adomby adom
Texas Instruments DC-DC Converters, VQFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+53@@ -0,0 +1,53 @@+# TPS62093RGTR++**Texas Instruments** · DC-DC Converters · VQFN-16-EP(3x3)++TPS62093RGTR from Texas Instruments, in a VQFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SW | bidirectional | Switch pin of the power stage. |+| 2 | SW | bidirectional | Switch pin of the power stage. |+| 3 | FREQ | input | Selects the switching frequency: Low sets 2.8 MHz typical and High sets 1.4 MHz typical; the pin has an active pull-down of about 400 kΩ and can be left floating for 2.8 MHz operation. |+| 4 | PG | output | Open-drain power good output that is high impedance when the output is within regulation and pulled low when the output is below its nominal value; the pull-up resistor must not connect to a voltage higher than the device input voltage. |+| 5 | FB | input | Feedback pin; for the adjustable version a resistor divider is connected here to set the output voltage, while for the fixed-output versions it may be connected to GND and has a pull-down of about 400 kΩ that is active when EN is low. |+| 6 | AGND | power_in | Analog ground; the exposed thermal pad is connected to AGND. |+| 7 | CP | bidirectional | Internal charge pump flying capacitor pin; connect a 10 nF capacitor between CP and CN. |+| 8 | CN | bidirectional | Internal charge pump flying capacitor pin; connect a 10 nF capacitor between CP and CN. |+| 9 | SS | input | Softstart control pin; a capacitor on this pin sets the softstart time, and leaving it floating sets the minimum start-up time. |+| 10 | AVIN | power_in | Bias supply input voltage pin. |+| 11 | PVIN | power_in | Power supply input voltage pin. |+| 12 | PVIN | power_in | Power supply input voltage pin. |+| 13 | EN | input | Device enable; it must be pulled high to enable the device and pulled low to disable it, with a pull-down of about 400 kΩ active when EN is low. |+| 14 | PGND | power_in | Power ground connection. |+| 15 | PGND | power_in | Power ground connection. |+| 16 | VOS | input | Output voltage sense pin; it must be connected to the output voltage. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-16-EP(3x3) |+| Category | Power Management (PMIC) |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `TPS62093RGTR`+- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`+- 3D model: VQFN-16-EP(3x3) (KiCad packages3D, STEP)+- 3D model files: `tps62093rgtr-etched.step` / `tps62093rgtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps62093rgtr.step` / `tps62093rgtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps62093.pdf) (32 pp, sha256 `1aca00440b3d4033`, retrieved 2026-10-08, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps62093rgtr-datasheet.pdf)
page.jsonadded+255@@ -0,0 +1,255 @@+{+ "slug": "tps62093rgtr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, VQFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "tps62093rgtr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps62093rgtr.kicad_sym",+ "tps62093rgtr.kicad_mod",+ "tps62093rgtr.glb",+ "tps62093rgtr.step",+ "tps62093rgtr.lbr",+ "docs/hero.png",+ "docs/tps62093rgtr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps62093rgtr-hero.glb",+ "tps62093rgtr-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS62093RGTR",+ "manufacturer": "Texas Instruments",+ "package": "VQFN-16-EP(3x3)",+ "pin_count": 17,+ "category": "Power Management (PMIC)",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/lit/ds/symlink/tps62093.pdf",+ "parts": {+ "symbol": "tps62093rgtr.kicad_sym",+ "footprint": "tps62093rgtr.kicad_mod",+ "model_3d": "tps62093rgtr-hero.glb",+ "model_3d_plain": "tps62093rgtr.glb",+ "model_3d_step": "tps62093rgtr-etched.step",+ "model_3d_step_plain": "tps62093rgtr.step",+ "lbr": "tps62093rgtr.lbr"+ },+ "distributor_links": {+ "lcsc": "C2876755",+ "digikey": "TPS62093RGTR-ND",+ "mouser": "595-TPS62093RGTR"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T17:10:12Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "TPS62093RGTR-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS62093RGTR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "SW",+ "type": "bidirectional",+ "description": "Switch pin of the power stage."+ },+ {+ "number": "2",+ "name": "SW",+ "type": "bidirectional",+ "description": "Switch pin of the power stage."+ },+ {+ "number": "3",+ "name": "FREQ",+ "type": "input",+ "description": "Selects the switching frequency: Low sets 2.8 MHz typical and High sets 1.4 MHz typical; the pin has an active pull-down of about 400 kΩ and can be left floating for 2.8 MHz operation."+ },+ {+ "number": "4",+ "name": "PG",+ "type": "output",+ "description": "Open-drain power good output that is high impedance when the output is within regulation and pulled low when the output is below its nominal value; the pull-up resistor must not connect to a voltage higher than the device input voltage."+ },+ {+ "number": "5",+ "name": "FB",+ "type": "input",+ "description": "Feedback pin; for the adjustable version a resistor divider is connected here to set the output voltage, while for the fixed-output versions it may be connected to GND and has a pull-down of about 400 kΩ that is active when EN is low."+ },+ {+ "number": "6",+ "name": "AGND",+ "type": "power_in",+ "description": "Analog ground; the exposed thermal pad is connected to AGND."+ },+ {+ "number": "7",+ "name": "CP",+ "type": "bidirectional",+ "description": "Internal charge pump flying capacitor pin; connect a 10 nF capacitor between CP and CN."+ },+ {+ "number": "8",+ "name": "CN",+ "type": "bidirectional",+ "description": "Internal charge pump flying capacitor pin; connect a 10 nF capacitor between CP and CN."+ },+ {+ "number": "9",+ "name": "SS",+ "type": "input",+ "description": "Softstart control pin; a capacitor on this pin sets the softstart time, and leaving it floating sets the minimum start-up time."+ },+ {+ "number": "10",+ "name": "AVIN",+ "type": "power_in",+ "description": "Bias supply input voltage pin."+ },+ {+ "number": "11",+ "name": "PVIN",+ "type": "power_in",+ "description": "Power supply input voltage pin."+ },+ {+ "number": "12",+ "name": "PVIN",+ "type": "power_in",+ "description": "Power supply input voltage pin."+ },+ {+ "number": "13",+ "name": "EN",+ "type": "input",+ "description": "Device enable; it must be pulled high to enable the device and pulled low to disable it, with a pull-down of about 400 kΩ active when EN is low."+ },+ {+ "number": "14",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground connection."+ },+ {+ "number": "15",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground connection."+ },+ {+ "number": "16",+ "name": "VOS",+ "type": "input",+ "description": "Output voltage sense pin; it must be connected to the output voltage."+ },+ {+ "number": "17",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The exposed thermal pad is not a numbered pin, so it is not in the pins list. The datasheet says it ; Package confirmed: the orderable addendum (page 22) lists TPS62093RGTR as VQFN (RGT), 16 pins, 3000 ; Pin types for SW, CP and CN are taken from the datasheet's I/O column and mapped to KiCad bidirectio",+ "exposed pad 17 added from the footprint"+ ],+ "pages_sent": 8,+ "cost_usd": 0.0705,+ "at": "2026-10-08T17:09:55"+ },+ "datasheet": {+ "url": "https://www.ti.com/lit/ds/symlink/tps62093.pdf",+ "pages": 32,+ "sha256": "1aca00440b3d4033",+ "source_tier": "mfr"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 17,+ "described": 17,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps62093rgtr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 3,+ 0.785+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "3eb81ffac423a66cdcfead8efe56401da171edaf1f2257049aad7b2d3900f6c8",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps62093rgtr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 3,+ 0.785+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "3db6e910eef14700c368dfe032f801a60076280476eae003b29c5d2430477000",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}