component
TPS61006DGSR
Public Made by Adomby adom
Texas Instruments DC-DC Converters, VSSOP-10-0.5mm. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+46@@ -0,0 +1,46 @@+# TPS61006DGSR++**Texas Instruments** · DC-DC Converters · VSSOP-10-0.5mm++TPS61006DGSR from Texas Instruments, in a VSSOP-10-0.5mm. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | EN | input | Chip-enable input: the converter is switched on when EN is high and switched off (shutdown) when EN is connected to ground. |+| 2 | COMP | passive | Error-amplifier compensation pin; connect an R-C-C network here to set the frequency response of the control loop. |+| 3 | FB | unconnected | Feedback input for adjustable output only (TPS61000); for the fixed-output TPS61006 this pin must be left unconnected. |+| 4 | GND | power_in | Ground pin. |+| 5 | VOUT | power_out | Output voltage; for the fixed-output versions the integrated resistive divider is connected to this pin. |+| 6 | VBAT | power_in | Supply pin for the converter; the device starts into a full load from supply voltages as low as 0.9 V and operates down to 0.8 V. |+| 7 | SW | input | Switch input pin; the node between the inductor and the anode of the rectifier diode connects to this pin, with absolute maximum SW voltage of VOUT + 0.7 V. |+| 8 | NC/FBGND | unconnected | Not connected on the TPS61006; it serves as the ground pin for the feedback resistor divider on the TPS61007 only. |+| 9 | LBI | input | Low-battery detector input; LBO is pulled low when LBI drops below the 500 mV threshold, and LBI must be tied to GND or VBAT if unused and must not be left floating. |+| 10 | LBO | output | Open-drain low-battery detector output that is pulled low when LBI falls below 500 mV; a pull-up resistor should be connected between LBO and VOUT. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VSSOP-10-0.5mm |+| Category | Power Supply Chip |+| Pins | 10 |++## CAD (KiCad official)++- Symbol: `TPS61006DGSR`+- Footprint: `Package_SO:MSOP-10_3x3mm_P0.5mm`+- 3D model: VSSOP-10-0.5mm (KiCad packages3D, STEP)+- 3D model files: `tps61006dgsr-etched.step` / `tps61006dgsr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps61006dgsr.step` / `tps61006dgsr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps61005) (31 pp, sha256 `2cac6e085a4ce051`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps61006dgsr-datasheet.pdf)
page.jsonadded+212@@ -0,0 +1,212 @@+{+ "slug": "tps61006dgsr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, VSSOP-10-0.5mm. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "tps61006dgsr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps61006dgsr.kicad_sym",+ "tps61006dgsr.kicad_mod",+ "tps61006dgsr.glb",+ "tps61006dgsr.step",+ "tps61006dgsr.lbr",+ "docs/hero.png",+ "docs/tps61006dgsr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps61006dgsr-hero.glb",+ "tps61006dgsr-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS61006DGSR",+ "manufacturer": "Texas Instruments",+ "package": "VSSOP-10-0.5mm",+ "pin_count": 10,+ "category": "Power Supply Chip",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps61005",+ "parts": {+ "symbol": "tps61006dgsr.kicad_sym",+ "footprint": "tps61006dgsr.kicad_mod",+ "model_3d": "tps61006dgsr-hero.glb",+ "model_3d_plain": "tps61006dgsr.glb",+ "model_3d_step": "tps61006dgsr-etched.step",+ "model_3d_step_plain": "tps61006dgsr.step",+ "lbr": "tps61006dgsr.lbr"+ },+ "distributor_links": {+ "lcsc": "C2072612",+ "digikey": "TPS61006DGSR-ND",+ "mouser": "595-TPS61006DGSR"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T15:32:28Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "TPS61006DGSR-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS61006DGSR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "EN",+ "type": "input",+ "description": "Chip-enable input: the converter is switched on when EN is high and switched off (shutdown) when EN is connected to ground."+ },+ {+ "number": "2",+ "name": "COMP",+ "type": "passive",+ "description": "Error-amplifier compensation pin; connect an R-C-C network here to set the frequency response of the control loop."+ },+ {+ "number": "3",+ "name": "FB",+ "type": "unconnected",+ "description": "Feedback input for adjustable output only (TPS61000); for the fixed-output TPS61006 this pin must be left unconnected."+ },+ {+ "number": "4",+ "name": "GND",+ "type": "power_in",+ "description": "Ground pin."+ },+ {+ "number": "5",+ "name": "VOUT",+ "type": "power_out",+ "description": "Output voltage; for the fixed-output versions the integrated resistive divider is connected to this pin."+ },+ {+ "number": "6",+ "name": "VBAT",+ "type": "power_in",+ "description": "Supply pin for the converter; the device starts into a full load from supply voltages as low as 0.9 V and operates down to 0.8 V."+ },+ {+ "number": "7",+ "name": "SW",+ "type": "input",+ "description": "Switch input pin; the node between the inductor and the anode of the rectifier diode connects to this pin, with absolute maximum SW voltage of VOUT + 0.7 V."+ },+ {+ "number": "8",+ "name": "NC/FBGND",+ "type": "unconnected",+ "description": "Not connected on the TPS61006; it serves as the ground pin for the feedback resistor divider on the TPS61007 only."+ },+ {+ "number": "9",+ "name": "LBI",+ "type": "input",+ "description": "Low-battery detector input; LBO is pulled low when LBI drops below the 500 mV threshold, and LBI must be tied to GND or VBAT if unused and must not be left floating."+ },+ {+ "number": "10",+ "name": "LBO",+ "type": "output",+ "description": "Open-drain low-battery detector output that is pulled low when LBI falls below 500 mV; a pull-up resistor should be connected between LBO and VOUT."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The I/O column for COMP is printed as a dash in the pin table, so the type 'passive' is my inference; FB and NC/FBGND are not connected on the TPS61006 fixed-output version; type set to 'unconnected' ba; The table gives I/O as O (VOUT) and I (VBAT); KiCad classes power_out and power_in were chosen from "+ ],+ "pages_sent": 8,+ "cost_usd": 0.0541,+ "at": "2026-10-08T15:32:01"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps61005",+ "pages": 31,+ "sha256": "2cac6e085a4ce051",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 10,+ "described": 10,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps61006dgsr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "b8f88eac3ce221c2ccb0b5048f9ad49c2ef4af148f8ae50c4e232e357683f547",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps61006dgsr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "9a5e6780dd0b7266495d188c673643ad9fa891c10ee07062e6f8f152c03965fe",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}