component
TPS57160QDGQRQ1
Public Made by Adomby adom
Texas Instruments DC-DC Converters, HVSSOP-10-EP-0.5mm. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+48@@ -0,0 +1,48 @@+# TPS57160QDGQRQ1++**Texas Instruments** · DC-DC Converters · HVSSOP-10-EP-0.5mm++TPS57160QDGQRQ1 from Texas Instruments, in a HVSSOP-10-EP-0.5mm. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | BOOT | output | A bootstrap capacitor is required between BOOT and PH, and if the voltage on this capacitor falls below the minimum required by the output device, the output is forced off until the capacitor is refreshed. |+| 2 | VIN | power_in | Input supply voltage, 3.5 V to 60 V, with an absolute maximum rating of -0.3 V to 65 V. |+| 3 | EN | input | Enable pin with an internal pullup current source; pull below 1.2 V to disable and float to enable, and use two resistors to adjust the input undervoltage lockout. |+| 4 | SS/TR | input | Slow-start and tracking pin where an external capacitor sets the output rise time, and the voltage on this pin overrides the internal reference for tracking and sequencing; absolute maximum -0.3 V to 3 V. |+| 5 | RT/CLK | input | Resistor timing and external clock pin that holds a fixed voltage when an external resistor to ground sets the switching frequency, and becomes a high-impedance synchronization input when pulled above the PLL upper threshold; absolute maximum -0.3 V to 3.6 V. |+| 6 | PWRGD | output | Open-drain power-good output that asserts low if the output voltage is low due to thermal shutdown, dropout, overvoltage, or EN shutdown; absolute maximum -0.3 V to 6 V with 10 mA sink current. |+| 7 | VSENSE | input | Inverting node of the transconductance (gm) error amplifier; absolute maximum -0.3 V to 3 V. |+| 8 | COMP | output | Error amplifier output and input to the output switch current comparator, where frequency compensation components connect; absolute maximum -0.3 V to 3 V. |+| 9 | GND | power_in | Ground pin, which must be electrically connected to the exposed thermal pad on the printed circuit board for proper operation. |+| 10 | PH | input | Source of the internal high-side power MOSFET, serving as the switch node of the regulator. |+| 11 | PowerPAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HVSSOP-10-EP-0.5mm |+| Category | Power Supply Chip |+| Pins | 11 |++## CAD (KiCad official)++- Symbol: `TPS57160QDGQRQ1`+- Footprint: `Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm`+- 3D model: HVSSOP-10-EP-0.5mm (KiCad packages3D, STEP)+- 3D model files: `tps57160qdgqrq1-etched.step` / `tps57160qdgqrq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps57160qdgqrq1.step` / `tps57160qdgqrq1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps57160-q1) (57 pp, sha256 `4830ba9678e27365`, retrieved 2026-10-08, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps57160qdgqrq1-datasheet.pdf)
page.jsonadded+218@@ -0,0 +1,218 @@+{+ "slug": "tps57160qdgqrq1",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, HVSSOP-10-EP-0.5mm. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "tps57160qdgqrq1",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps57160qdgqrq1.kicad_sym",+ "tps57160qdgqrq1.kicad_mod",+ "tps57160qdgqrq1.glb",+ "tps57160qdgqrq1.step",+ "tps57160qdgqrq1.lbr",+ "docs/hero.png",+ "docs/tps57160qdgqrq1-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps57160qdgqrq1-hero.glb",+ "tps57160qdgqrq1-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS57160QDGQRQ1",+ "manufacturer": "Texas Instruments",+ "package": "HVSSOP-10-EP-0.5mm",+ "pin_count": 11,+ "category": "Power Supply Chip",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps57160-q1",+ "parts": {+ "symbol": "tps57160qdgqrq1.kicad_sym",+ "footprint": "tps57160qdgqrq1.kicad_mod",+ "model_3d": "tps57160qdgqrq1-hero.glb",+ "model_3d_plain": "tps57160qdgqrq1.glb",+ "model_3d_step": "tps57160qdgqrq1-etched.step",+ "model_3d_step_plain": "tps57160qdgqrq1.step",+ "lbr": "tps57160qdgqrq1.lbr"+ },+ "distributor_links": {+ "lcsc": "C527563",+ "digikey": "296-28174-2-ND",+ "mouser": "595-TPS57160QDGQRQ1"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T03:21:51Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-28174-2-ND",+ "status": "found"+ },+ "mouser": {+ "pn": "595-TPS57160QDGQRQ1",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "BOOT",+ "type": "output",+ "description": "A bootstrap capacitor is required between BOOT and PH, and if the voltage on this capacitor falls below the minimum required by the output device, the output is forced off until the capacitor is refreshed."+ },+ {+ "number": "2",+ "name": "VIN",+ "type": "power_in",+ "description": "Input supply voltage, 3.5 V to 60 V, with an absolute maximum rating of -0.3 V to 65 V."+ },+ {+ "number": "3",+ "name": "EN",+ "type": "input",+ "description": "Enable pin with an internal pullup current source; pull below 1.2 V to disable and float to enable, and use two resistors to adjust the input undervoltage lockout."+ },+ {+ "number": "4",+ "name": "SS/TR",+ "type": "input",+ "description": "Slow-start and tracking pin where an external capacitor sets the output rise time, and the voltage on this pin overrides the internal reference for tracking and sequencing; absolute maximum -0.3 V to 3 V."+ },+ {+ "number": "5",+ "name": "RT/CLK",+ "type": "input",+ "description": "Resistor timing and external clock pin that holds a fixed voltage when an external resistor to ground sets the switching frequency, and becomes a high-impedance synchronization input when pulled above the PLL upper threshold; absolute maximum -0.3 V to 3.6 V."+ },+ {+ "number": "6",+ "name": "PWRGD",+ "type": "output",+ "description": "Open-drain power-good output that asserts low if the output voltage is low due to thermal shutdown, dropout, overvoltage, or EN shutdown; absolute maximum -0.3 V to 6 V with 10 mA sink current."+ },+ {+ "number": "7",+ "name": "VSENSE",+ "type": "input",+ "description": "Inverting node of the transconductance (gm) error amplifier; absolute maximum -0.3 V to 3 V."+ },+ {+ "number": "8",+ "name": "COMP",+ "type": "output",+ "description": "Error amplifier output and input to the output switch current comparator, where frequency compensation components connect; absolute maximum -0.3 V to 3 V."+ },+ {+ "number": "9",+ "name": "GND",+ "type": "power_in",+ "description": "Ground pin, which must be electrically connected to the exposed thermal pad on the printed circuit board for proper operation."+ },+ {+ "number": "10",+ "name": "PH",+ "type": "input",+ "description": "Source of the internal high-side power MOSFET, serving as the switch node of the regulator."+ },+ {+ "number": "11",+ "name": "PowerPAD",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The exposed thermal pad is part of the DGQ package but the datasheet gives it no pin number, so it i; The datasheet pin table lists PH as type 'I' (input). The pin is the source of the internal high-sid; The absolute maximum ratings table for PH (VOUT / switch node) is garbled in the extracted text, so ",+ "exposed pad 11 added from the footprint"+ ],+ "pages_sent": 9,+ "cost_usd": 0.0595,+ "at": "2026-10-08T03:21:34"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps57160-q1",+ "pages": 57,+ "sha256": "4830ba9678e27365",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 11,+ "described": 11,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps57160qdgqrq1.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 0.95+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "18605eed706df7bb9674107abe7aa36e0ba163a09c21a2cee6c75cfa291b7937",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps57160qdgqrq1-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 0.95+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "70749bbb83fa054f948581741211071c0a54a144dce2d4f009c740e8e5318131",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}