component
TPS55330RTER
Public Made by Adomby adom
Texas Instruments DC-DC Converters, QFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+54@@ -0,0 +1,54 @@+# TPS55330RTER++**Texas Instruments** · DC-DC Converters · QFN-16-EP(3x3)++TPS55330RTER from Texas Instruments, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SW | output | The drain of the internal 5A, 24V power MOSFET switch connected to the boost or SEPIC inductor or flyback transformer. |+| 2 | VIN | power_in | Input supply pin; connect to supply voltage between 2.9 V and 16 V. |+| 3 | EN | input | Enable pin; when voltage falls below enable threshold approximately 0.92 V for more than 1 ms, the IC turns off. |+| 4 | SS | input | Soft-start programming pin; connect capacitor between SS and AGND to program soft-start timing with internal 6 µA charging current. |+| 5 | SYNC | input | Switching frequency synchronization pin accepting external clock signal from 0 V to 5 V with logic levels (high ≥1.2 V, low ≤0.4 V) to set frequency between 200 kHz and 1 MHz; tie to AGND if not used. |+| 6 | AGND | power_in | Signal ground of the IC providing reference for control circuits. |+| 7 | COMP | output | Output of the transconductance error amplifier with clamp voltage ranging from 0.75 V to 3.1 V; connect external RC compensation network to this pin. |+| 8 | FB | input | Voltage feedback input to error amplifier regulated to 1.229 V reference; connect to center tap of resistor divider to program output voltage. |+| 9 | FREQ | input | Switching frequency programming pin; connect external resistor to AGND to set switching frequency from 100 kHz to 1.2 MHz with internal 1.25 V reference voltage. |+| 10 | NC | unconnected | Reserved pin; must be connected to AGND. |+| 11 | PGND | power_in | Power ground connected to source of internal power MOSFET switch; high current return path for power stage. |+| 12 | PGND | power_in | Power ground connected to source of internal power MOSFET switch; high current return path for power stage. |+| 13 | PGND | power_in | Power ground connected to source of internal power MOSFET switch; high current return path for power stage. |+| 14 | NC | unconnected | Reserved pin; must be connected to AGND. |+| 15 | SW | output | The drain of the internal 5A, 24V power MOSFET switch connected to the boost or SEPIC inductor or flyback transformer. |+| 16 | SW | output | The drain of the internal 5A, 24V power MOSFET switch connected to the boost or SEPIC inductor or flyback transformer. |+| 17 | PowerPAD | power_in | Thermal pad; solder to AGND for enhanced power dissipation using thermal vias to internal ground plane. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | QFN-16-EP(3x3) |+| Category | Power Management (PMIC) |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `TPS55330RTER`+- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`+- 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)+- 3D model files: `tps55330rter-etched.step` / `tps55330rter-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps55330rter.step` / `tps55330rter.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps55330) (34 pp, sha256 `7c83c5fe8038a1ec`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps55330rter-datasheet.pdf)
page.jsonadded+195@@ -0,0 +1,195 @@+{+ "slug": "tps55330rter",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, QFN-16-EP(3x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "tps55330rter",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps55330rter.kicad_sym",+ "tps55330rter.kicad_mod",+ "tps55330rter.glb",+ "tps55330rter.step",+ "tps55330rter.lbr",+ "docs/hero.png",+ "docs/tps55330rter-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "component": {+ "mpn": "TPS55330RTER",+ "manufacturer": "Texas Instruments",+ "package": "QFN-16-EP(3x3)",+ "pin_count": 17,+ "category": "Power Management (PMIC)",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps55330",+ "parts": {+ "symbol": "tps55330rter.kicad_sym",+ "footprint": "tps55330rter.kicad_mod",+ "model_3d": "tps55330rter-etched.glb",+ "model_3d_plain": "tps55330rter.glb",+ "model_3d_step": "tps55330rter-etched.step",+ "model_3d_step_plain": "tps55330rter.step",+ "lbr": "tps55330rter.lbr"+ },+ "distributor_links": {+ "lcsc": "C33616"+ },+ "pins": [+ {+ "number": "1",+ "name": "SW",+ "type": "output",+ "description": "The drain of the internal 5A, 24V power MOSFET switch connected to the boost or SEPIC inductor or flyback transformer."+ },+ {+ "number": "2",+ "name": "VIN",+ "type": "power_in",+ "description": "Input supply pin; connect to supply voltage between 2.9 V and 16 V."+ },+ {+ "number": "3",+ "name": "EN",+ "type": "input",+ "description": "Enable pin; when voltage falls below enable threshold approximately 0.92 V for more than 1 ms, the IC turns off."+ },+ {+ "number": "4",+ "name": "SS",+ "type": "input",+ "description": "Soft-start programming pin; connect capacitor between SS and AGND to program soft-start timing with internal 6 µA charging current."+ },+ {+ "number": "5",+ "name": "SYNC",+ "type": "input",+ "description": "Switching frequency synchronization pin accepting external clock signal from 0 V to 5 V with logic levels (high ≥1.2 V, low ≤0.4 V) to set frequency between 200 kHz and 1 MHz; tie to AGND if not used."+ },+ {+ "number": "6",+ "name": "AGND",+ "type": "power_in",+ "description": "Signal ground of the IC providing reference for control circuits."+ },+ {+ "number": "7",+ "name": "COMP",+ "type": "output",+ "description": "Output of the transconductance error amplifier with clamp voltage ranging from 0.75 V to 3.1 V; connect external RC compensation network to this pin."+ },+ {+ "number": "8",+ "name": "FB",+ "type": "input",+ "description": "Voltage feedback input to error amplifier regulated to 1.229 V reference; connect to center tap of resistor divider to program output voltage."+ },+ {+ "number": "9",+ "name": "FREQ",+ "type": "input",+ "description": "Switching frequency programming pin; connect external resistor to AGND to set switching frequency from 100 kHz to 1.2 MHz with internal 1.25 V reference voltage."+ },+ {+ "number": "10",+ "name": "NC",+ "type": "unconnected",+ "description": "Reserved pin; must be connected to AGND."+ },+ {+ "number": "11",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground connected to source of internal power MOSFET switch; high current return path for power stage."+ },+ {+ "number": "12",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground connected to source of internal power MOSFET switch; high current return path for power stage."+ },+ {+ "number": "13",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground connected to source of internal power MOSFET switch; high current return path for power stage."+ },+ {+ "number": "14",+ "name": "NC",+ "type": "unconnected",+ "description": "Reserved pin; must be connected to AGND."+ },+ {+ "number": "15",+ "name": "SW",+ "type": "output",+ "description": "The drain of the internal 5A, 24V power MOSFET switch connected to the boost or SEPIC inductor or flyback transformer."+ },+ {+ "number": "16",+ "name": "SW",+ "type": "output",+ "description": "The drain of the internal 5A, 24V power MOSFET switch connected to the boost or SEPIC inductor or flyback transformer."+ },+ {+ "number": "17",+ "name": "PowerPAD",+ "type": "power_in",+ "description": "Thermal pad; solder to AGND for enhanced power dissipation using thermal vias to internal ground plane."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.2",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.2",+ "primary_model": "claude-haiku-4-5-20251001",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [],+ "pages_sent": 34,+ "cost_usd": 0.3274,+ "at": "2026-09-23T09:01:07"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps55330",+ "pages": 34,+ "sha256": "7c83c5fe8038a1ec",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 17,+ "described": 17,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}