component
TPS54561QDPRTQ1
Public Made by Adomby adom
Texas Instruments DC-DC Converters, WSON-10-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+48@@ -0,0 +1,48 @@+# TPS54561QDPRTQ1++**Texas Instruments** · DC-DC Converters · WSON-10-EP(4x4)++TPS54561QDPRTQ1 from Texas Instruments, in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | BOOT | output | The device requires a bootstrap capacitor between BOOT and SW; if the voltage on this capacitor falls below the minimum required to operate the high-side MOSFET, the gate driver switches off until the capacitor recharges. |+| 2 | VDD | power_in | Input supply pin with a 4.5-V to 60-V operating range. |+| 3 | EN | input | Enable pin with an internal pullup current source; pull below 1.2 V to disable and float to enable, and the input undervoltage lockout can be adjusted with two resistors. |+| 4 | SS/TR | input | Soft-start and tracking input; an external capacitor sets the output rise time, and a voltage applied to this pin overrides the internal reference to allow tracking and sequencing. |+| 5 | RT/CLK | input | Resistor timing and external clock input; an external resistor to ground sets the switching frequency, and when pulled above the PLL upper threshold the pin becomes a high-impedance synchronization clock input. |+| 6 | FB | input | Inverting input of the transconductance (gm) error amplifier. |+| 7 | COMP | output | Error amplifier output and input to the output switch-current comparator (PWM comparator); frequency compensation components connect to this pin. |+| 8 | GND | power_in | Ground pin; to ensure proper operation, it must be electrically connected to the copper pad under the IC on the printed circuit board. |+| 9 | SW | input | Source of the internal high-side power MOSFET and the switching node of the converter (datasheet I/O column lists this pin as I). |+| 10 | PWRGD | output | Open-drain power-good output that asserts when the output voltage is low because of thermal shutdown, dropout, overvoltage, or EN shutdown. |+| 11 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | WSON-10-EP(4x4) |+| Category | Power Supply Chip |+| Pins | 11 |++## CAD (KiCad official)++- Symbol: `TPS54561QDPRTQ1`+- Footprint: `Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm`+- 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `tps54561qdprtq1-etched.step` / `tps54561qdprtq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps54561qdprtq1.step` / `tps54561qdprtq1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps54561-q1) (54 pp, sha256 `6999bc04acb346ca`, retrieved 2026-10-08, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps54561qdprtq1-datasheet.pdf)
page.jsonadded+219@@ -0,0 +1,219 @@+{+ "slug": "tps54561qdprtq1",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, WSON-10-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "tps54561qdprtq1",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps54561qdprtq1.kicad_sym",+ "tps54561qdprtq1.kicad_mod",+ "tps54561qdprtq1.glb",+ "tps54561qdprtq1.step",+ "tps54561qdprtq1.lbr",+ "docs/hero.png",+ "docs/tps54561qdprtq1-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps54561qdprtq1-hero.glb",+ "tps54561qdprtq1-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS54561QDPRTQ1",+ "manufacturer": "Texas Instruments",+ "package": "WSON-10-EP(4x4)",+ "pin_count": 11,+ "category": "Power Supply Chip",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps54561-q1",+ "parts": {+ "symbol": "tps54561qdprtq1.kicad_sym",+ "footprint": "tps54561qdprtq1.kicad_mod",+ "model_3d": "tps54561qdprtq1-hero.glb",+ "model_3d_plain": "tps54561qdprtq1.glb",+ "model_3d_step": "tps54561qdprtq1-etched.step",+ "model_3d_step_plain": "tps54561qdprtq1.step",+ "lbr": "tps54561qdprtq1.lbr"+ },+ "distributor_links": {+ "lcsc": "C201961",+ "digikey": "296-46240-2-ND",+ "mouser": "595-TPS54561QDPRTQ1"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T02:49:42Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-46240-2-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS54561QDPRTQ1",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "BOOT",+ "type": "output",+ "description": "The device requires a bootstrap capacitor between BOOT and SW; if the voltage on this capacitor falls below the minimum required to operate the high-side MOSFET, the gate driver switches off until the capacitor recharges."+ },+ {+ "number": "2",+ "name": "VDD",+ "type": "power_in",+ "description": "Input supply pin with a 4.5-V to 60-V operating range."+ },+ {+ "number": "3",+ "name": "EN",+ "type": "input",+ "description": "Enable pin with an internal pullup current source; pull below 1.2 V to disable and float to enable, and the input undervoltage lockout can be adjusted with two resistors."+ },+ {+ "number": "4",+ "name": "SS/TR",+ "type": "input",+ "description": "Soft-start and tracking input; an external capacitor sets the output rise time, and a voltage applied to this pin overrides the internal reference to allow tracking and sequencing."+ },+ {+ "number": "5",+ "name": "RT/CLK",+ "type": "input",+ "description": "Resistor timing and external clock input; an external resistor to ground sets the switching frequency, and when pulled above the PLL upper threshold the pin becomes a high-impedance synchronization clock input."+ },+ {+ "number": "6",+ "name": "FB",+ "type": "input",+ "description": "Inverting input of the transconductance (gm) error amplifier."+ },+ {+ "number": "7",+ "name": "COMP",+ "type": "output",+ "description": "Error amplifier output and input to the output switch-current comparator (PWM comparator); frequency compensation components connect to this pin."+ },+ {+ "number": "8",+ "name": "GND",+ "type": "power_in",+ "description": "Ground pin; to ensure proper operation, it must be electrically connected to the copper pad under the IC on the printed circuit board."+ },+ {+ "number": "9",+ "name": "SW",+ "type": "input",+ "description": "Source of the internal high-side power MOSFET and the switching node of the converter (datasheet I/O column lists this pin as I)."+ },+ {+ "number": "10",+ "name": "PWRGD",+ "type": "output",+ "description": "Open-drain power-good output that asserts when the output voltage is low because of thermal shutdown, dropout, overvoltage, or EN shutdown."+ },+ {+ "number": "11",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The DPR package has an exposed thermal pad (labelled 'Thermal Pad 3' in the pin diagram and '—' in t; Pin 9 (SW) is listed as type 'I' in the datasheet's I/O column, but it is functionally the converter; Pin 1 (BOOT) is listed as 'O' in the datasheet, mapped here to KiCad 'output'; some symbol libraries",+ "exposed pad 11 added from the footprint"+ ],+ "pages_sent": 7,+ "cost_usd": 0.0557,+ "at": "2026-10-08T02:49:25"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps54561-q1",+ "pages": 54,+ "sha256": "6999bc04acb346ca",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 11,+ "described": 11,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps54561qdprtq1.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4,+ 3.95,+ 0.8+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "ef3c2f392fea7049285bfc942095cbd03d5bb47d74597dd80d1bc887363be656",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps54561qdprtq1-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4,+ 3.95,+ 0.8+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "fecc59fc1bced1568b0280e9f4ba36308fe71f10a46b3a3746b6a56c3050d07d",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}