component
TPS54240DGQR
Public Made by Adomby adom
Texas Instruments DC-DC Converters, MSOP-10-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+47@@ -0,0 +1,47 @@+# TPS54240DGQR++**Texas Instruments** · DC-DC Converters · MSOP-10-EP++TPS54240DGQR from Texas Instruments, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | BOOT | output | A bootstrap capacitor is required between BOOT and PH; if its voltage falls below the minimum required by the output device, the output is forced to switch off until the capacitor is refreshed. |+| 2 | VIN | power_in | Input supply voltage, 3.5 V to 42 V (absolute maximum VIN is 47 V). |+| 3 | EN | input | Enable pin with internal pullup current source; pull below 1.2 V to disable and float to enable, and adjust the input undervoltage lockout with two resistors. |+| 4 | SS/TR | input | Slow-start and tracking pin; an external capacitor sets the output rise time, and because this pin overrides the internal reference it can be used for tracking and sequencing (absolute maximum 3 V). |+| 5 | RT/CLK | input | Resistor timing and external clock pin; an external resistor to ground sets the switching frequency, and pulling the pin above the PLL upper threshold converts it to a high-impedance synchronization clock input (absolute maximum 3.6 V). |+| 6 | PWRGD | output | Open-drain output that asserts low if the output voltage is low due to thermal shutdown, dropout, overvoltage or EN shutdown; absolute maximum sink current is 10 mA. |+| 7 | VSENSE | input | Inverting node of the transconductance (gm) error amplifier; absolute maximum rating is -0.3 V to 3 V. |+| 8 | COMP | output | Error amplifier output and input to the output switch current comparator; frequency compensation components connect to this pin (absolute maximum -0.3 V to 3 V). |+| 9 | GND | power_in | Ground pin. |+| 10 | PH | input | Source of the internal high-side power MOSFET; absolute maximum rating is -0.6 V to 47 V, with -2 V to 47 V allowed for a 10-ns transient. |+| 11 | PowerPAD | power_in | GND pin that must be electrically connected to the exposed pad on the printed circuit board for proper operation; the voltage difference between PAD and GND is limited to ±200 mV. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | MSOP-10-EP |+| Category | Power Management (PMIC) |+| Pins | 11 |++## CAD (KiCad official)++- Symbol: `TPS54240DGQR`+- Footprint: `Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm`+- 3D model: MSOP-10-EP (KiCad packages3D, STEP)+- 3D model files: `tps54240dgqr-etched.step` / `tps54240dgqr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps54240dgqr.step` / `tps54240dgqr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps54240) (60 pp, sha256 `160dce77f667b76a`, retrieved 2026-10-07, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps54240dgqr-datasheet.pdf)
page.jsonadded+218@@ -0,0 +1,218 @@+{+ "slug": "tps54240dgqr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, MSOP-10-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "tps54240dgqr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps54240dgqr.kicad_sym",+ "tps54240dgqr.kicad_mod",+ "tps54240dgqr.glb",+ "tps54240dgqr.step",+ "tps54240dgqr.lbr",+ "docs/hero.png",+ "docs/tps54240dgqr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps54240dgqr-hero.glb",+ "tps54240dgqr-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS54240DGQR",+ "manufacturer": "Texas Instruments",+ "package": "MSOP-10-EP",+ "pin_count": 11,+ "category": "Power Management (PMIC)",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/tps54240",+ "parts": {+ "symbol": "tps54240dgqr.kicad_sym",+ "footprint": "tps54240dgqr.kicad_mod",+ "model_3d": "tps54240dgqr-hero.glb",+ "model_3d_plain": "tps54240dgqr.glb",+ "model_3d_step": "tps54240dgqr-etched.step",+ "model_3d_step_plain": "tps54240dgqr.step",+ "lbr": "tps54240dgqr.lbr"+ },+ "distributor_links": {+ "lcsc": "C53213",+ "digikey": "296-27414-2-ND",+ "mouser": "595-TPS54240DGQR"+ },+ "distributor_check": {+ "checked_at": "2026-10-07T21:38:24Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-27414-2-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS54240DGQR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "BOOT",+ "type": "output",+ "description": "A bootstrap capacitor is required between BOOT and PH; if its voltage falls below the minimum required by the output device, the output is forced to switch off until the capacitor is refreshed."+ },+ {+ "number": "2",+ "name": "VIN",+ "type": "power_in",+ "description": "Input supply voltage, 3.5 V to 42 V (absolute maximum VIN is 47 V)."+ },+ {+ "number": "3",+ "name": "EN",+ "type": "input",+ "description": "Enable pin with internal pullup current source; pull below 1.2 V to disable and float to enable, and adjust the input undervoltage lockout with two resistors."+ },+ {+ "number": "4",+ "name": "SS/TR",+ "type": "input",+ "description": "Slow-start and tracking pin; an external capacitor sets the output rise time, and because this pin overrides the internal reference it can be used for tracking and sequencing (absolute maximum 3 V)."+ },+ {+ "number": "5",+ "name": "RT/CLK",+ "type": "input",+ "description": "Resistor timing and external clock pin; an external resistor to ground sets the switching frequency, and pulling the pin above the PLL upper threshold converts it to a high-impedance synchronization clock input (absolute maximum 3.6 V)."+ },+ {+ "number": "6",+ "name": "PWRGD",+ "type": "output",+ "description": "Open-drain output that asserts low if the output voltage is low due to thermal shutdown, dropout, overvoltage or EN shutdown; absolute maximum sink current is 10 mA."+ },+ {+ "number": "7",+ "name": "VSENSE",+ "type": "input",+ "description": "Inverting node of the transconductance (gm) error amplifier; absolute maximum rating is -0.3 V to 3 V."+ },+ {+ "number": "8",+ "name": "COMP",+ "type": "output",+ "description": "Error amplifier output and input to the output switch current comparator; frequency compensation components connect to this pin (absolute maximum -0.3 V to 3 V)."+ },+ {+ "number": "9",+ "name": "GND",+ "type": "power_in",+ "description": "Ground pin."+ },+ {+ "number": "10",+ "name": "PH",+ "type": "input",+ "description": "Source of the internal high-side power MOSFET; absolute maximum rating is -0.6 V to 47 V, with -2 V to 47 V allowed for a 10-ns transient."+ },+ {+ "number": "11",+ "name": "PowerPAD",+ "type": "power_in",+ "description": "GND pin that must be electrically connected to the exposed pad on the printed circuit board for proper operation; the voltage difference between PAD and GND is limited to ±200 mV."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Package hint says MSOP-10-EP, but the datasheet and the orderable addendum list TPS54240DGQR as HVSS; The datasheet pin table classifies PH as 'I' and VIN as 'I'. Both were kept as printed (PH input) or; The thermal pad is labelled '11' (POWERPAD) on the drawing and in the pin table, not a numbered lead"+ ],+ "pages_sent": 8,+ "cost_usd": 0.0605,+ "at": "2026-10-07T21:38:06"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/tps54240",+ "pages": 60,+ "sha256": "160dce77f667b76a",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 11,+ "described": 11,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps54240dgqr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 0.95+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "18605eed706df7bb9674107abe7aa36e0ba163a09c21a2cee6c75cfa291b7937",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps54240dgqr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 0.95+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "4487af8dd0e6acd017658536f5a7eb30a2db4d26ea81b4fce09c6a4f635fa3e1",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}