component
TPS2549IRTERQ1
Public Made by Adomby adom
Texas Instruments USB Converters, QFN-16-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
page.json+15−12@@ -38,25 +38,25 @@ "number": "1", "name": "IN", "type": "power_in",- "description": "Input supply voltage 4.5-6.5 V; connect 0.1 \u00b5F bypass capacitor as close as possible to the IC."+ "description": "Input supply voltage 4.5-6.5 V; connect 0.1 µF bypass capacitor as close as possible to the IC." }, { "number": "2", "name": "DM_OUT", "type": "bidirectional",- "description": "D- data line to upstream USB host controller with high-bandwidth analog switch (925 MHz bandwidth, 2-6 \u03a9 on-resistance)."+ "description": "D- data line to upstream USB host controller with high-bandwidth analog switch (925 MHz bandwidth, 2-6 Ω on-resistance)." }, { "number": "3", "name": "DP_OUT", "type": "bidirectional",- "description": "D+ data line to upstream USB host controller with high-bandwidth analog switch (925 MHz bandwidth, 2-6 \u03a9 on-resistance)."+ "description": "D+ data line to upstream USB host controller with high-bandwidth analog switch (925 MHz bandwidth, 2-6 Ω on-resistance)." }, { "number": "4", "name": "CS", "type": "output",- "description": "Current-sink output providing proportional feedback (75 \u00b5A/A) proportional to OUT load current for cable-compensation loop."+ "description": "Current-sink output providing proportional feedback (75 µA/A) proportional to OUT load current for cable-compensation loop." }, { "number": "5",@@ -86,31 +86,31 @@ "number": "9", "name": "STATUS", "type": "tri_state",- "description": "Active-low open-drain output asserts when load exceeds load-detection threshold (700 mA typical with 80.6 k\u03a9 ILIM_LO resistor, 210 ms response time)."+ "description": "Active-low open-drain output asserts when load exceeds load-detection threshold (700 mA typical with 80.6 kΩ ILIM_LO resistor, 210 ms response time)." }, { "number": "10", "name": "DP_IN", "type": "bidirectional",- "description": "D+ data line from downstream connector with ESD protection (\u00b18 kV contact discharge, \u00b115 kV air discharge per IEC 61000-4-2) and short-to-VBUS overvoltage protection (3.9 V trip threshold)."+ "description": "D+ data line from downstream connector with ESD protection (±8 kV contact discharge, ±15 kV air discharge per IEC 61000-4-2) and short-to-VBUS overvoltage protection (3.9 V trip threshold)." }, { "number": "11", "name": "DM_IN", "type": "bidirectional",- "description": "D- data line from downstream connector with ESD protection (\u00b18 kV contact discharge, \u00b115 kV air discharge per IEC 61000-4-2) and short-to-VBUS overvoltage protection (3.9 V trip threshold)."+ "description": "D- data line from downstream connector with ESD protection (±8 kV contact discharge, ±15 kV air discharge per IEC 61000-4-2) and short-to-VBUS overvoltage protection (3.9 V trip threshold)." }, { "number": "12", "name": "OUT", "type": "power_out",- "description": "Power-switch output with maximum continuous current 3.2 A and on-resistance 47 m\u03a9 typical (47-80 m\u03a9 over -40\u00b0C to 125\u00b0C)."+ "description": "Power-switch output with maximum continuous current 3.2 A and on-resistance 47 mΩ typical (47-80 mΩ over -40°C to 125°C)." }, { "number": "13", "name": "FAULT", "type": "tri_state",- "description": "Active-low open-drain output asserts on overtemperature (>155\u00b0C or >135\u00b0C in current-limit mode), overcurrent (>programmed IOS), or DP_IN/DM_IN overvoltage (>3.9 V) with 8 ms deglitch."+ "description": "Active-low open-drain output asserts on overtemperature (>155°C or >135°C in current-limit mode), overcurrent (>programmed IOS), or DP_IN/DM_IN overvoltage (>3.9 V) with 8 ms deglitch." }, { "number": "14",@@ -122,13 +122,13 @@ "number": "15", "name": "ILIM_LO", "type": "input",- "description": "Low current-limit setting input; connect external resistor to GND to program threshold using I(OS) = 53762 / [R(ILIM_LO) \u00d7 1.0021], range 10.4-1000 k\u03a9."+ "description": "Low current-limit setting input; connect external resistor to GND to program threshold using I(OS) = 53762 / [R(ILIM_LO) × 1.0021], range 10.4-1000 kΩ." }, { "number": "16", "name": "ILIM_HI", "type": "input",- "description": "High current-limit setting input; connect external resistor to GND to program threshold using I(OS) = 53762 / [R(ILIM_HI) \u00d7 1.0021], range 10.4-1000 k\u03a9."+ "description": "High current-limit setting input; connect external resistor to GND to program threshold using I(OS) = 53762 / [R(ILIM_HI) × 1.0021], range 10.4-1000 kΩ." }, { "number": "17",@@ -215,5 +215,8 @@ "docs/tps2549irterq1-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }