← Commit history

Initial commit: component/tps2549irterq1

Ray ·3c401c677a ·
2 files changed +252
README.mdadded+54
@@ -0,0 +1,54 @@+# TPS2549IRTERQ1++**Texas Instruments** · USB Converters · QFN-16-EP(3x3)++TPS2549IRTERQ1 from Texas Instruments, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | IN | power_in | Input supply voltage 4.5-6.5 V; connect 0.1 µF bypass capacitor as close as possible to the IC. |+| 2 | DM_OUT | bidirectional | D- data line to upstream USB host controller with high-bandwidth analog switch (925 MHz bandwidth, 2-6 Ω on-resistance). |+| 3 | DP_OUT | bidirectional | D+ data line to upstream USB host controller with high-bandwidth analog switch (925 MHz bandwidth, 2-6 Ω on-resistance). |+| 4 | CS | output | Current-sink output providing proportional feedback (75 µA/A) proportional to OUT load current for cable-compensation loop. |+| 5 | EN | input | Active-high logic input enabling power and signal switches (1.35 V rising threshold, 200 mV hysteresis); device enters UVLO at 4.1 V. |+| 6 | CTL1 | input | Logic-level control input for charging mode selection; tie directly to IN or GND without pullup or pulldown resistor. |+| 7 | CTL2 | input | Logic-level control input for charging mode selection; tie directly to IN or GND without pullup or pulldown resistor. |+| 8 | CTL3 | input | Logic-level control input for charging mode selection; tie directly to IN or GND without pullup or pulldown resistor. |+| 9 | STATUS | tri_state | Active-low open-drain output asserts when load exceeds load-detection threshold (700 mA typical with 80.6 kΩ ILIM_LO resistor, 210 ms response time). |+| 10 | DP_IN | bidirectional | D+ data line from downstream connector with ESD protection (±8 kV contact discharge, ±15 kV air discharge per IEC 61000-4-2) and short-to-VBUS overvoltage protection (3.9 V trip threshold). |+| 11 | DM_IN | bidirectional | D- data line from downstream connector with ESD protection (±8 kV contact discharge, ±15 kV air discharge per IEC 61000-4-2) and short-to-VBUS overvoltage protection (3.9 V trip threshold). |+| 12 | OUT | power_out | Power-switch output with maximum continuous current 3.2 A and on-resistance 47 mΩ typical (47-80 mΩ over -40°C to 125°C). |+| 13 | FAULT | tri_state | Active-low open-drain output asserts on overtemperature (>155°C or >135°C in current-limit mode), overcurrent (>programmed IOS), or DP_IN/DM_IN overvoltage (>3.9 V) with 8 ms deglitch. |+| 14 | GND | power_in | Ground connection; thermal pad internally connected to GND and must be soldered to PCB ground plane. |+| 15 | ILIM_LO | input | Low current-limit setting input; connect external resistor to GND to program threshold using I(OS) = 53762 / [R(ILIM_LO) × 1.0021], range 10.4-1000 kΩ. |+| 16 | ILIM_HI | input | High current-limit setting input; connect external resistor to GND to program threshold using I(OS) = 53762 / [R(ILIM_HI) × 1.0021], range 10.4-1000 kΩ. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | QFN-16-EP(3x3) |+| Category | Interface |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `TPS2549IRTERQ1`+- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`+- 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)+- 3D model files: `tps2549irterq1-etched.step` / `tps2549irterq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps2549irterq1.step` / `tps2549irterq1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps2549-q1) (46 pp, sha256 `4d8861e6d954954c`, retrieved 2026-09-18, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps2549irterq1-datasheet.pdf)
page.jsonadded+198
@@ -0,0 +1,198 @@+{+  "slug": "tps2549irterq1",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments USB Converters, QFN-16-EP(3x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "interface",+    "tps2549irterq1",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps2549irterq1.kicad_sym",+    "tps2549irterq1.kicad_mod",+    "tps2549irterq1.glb",+    "tps2549irterq1.step",+    "tps2549irterq1.lbr",+    "docs/hero.png",+    "docs/tps2549irterq1-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS2549IRTERQ1",+    "manufacturer": "Texas Instruments",+    "package": "QFN-16-EP(3x3)",+    "pin_count": 17,+    "category": "Interface",+    "subcategory": "USB Converters",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps2549-q1",+    "parts": {+      "symbol": "tps2549irterq1.kicad_sym",+      "footprint": "tps2549irterq1.kicad_mod",+      "model_3d": "tps2549irterq1-etched.glb",+      "model_3d_plain": "tps2549irterq1.glb",+      "model_3d_step": "tps2549irterq1-etched.step",+      "model_3d_step_plain": "tps2549irterq1.step",+      "lbr": "tps2549irterq1.lbr"+    },+    "distributor_links": {+      "lcsc": "C181611"+    },+    "pins": [+      {+        "number": "1",+        "name": "IN",+        "type": "power_in",+        "description": "Input supply voltage 4.5-6.5 V; connect 0.1 µF bypass capacitor as close as possible to the IC."+      },+      {+        "number": "2",+        "name": "DM_OUT",+        "type": "bidirectional",+        "description": "D- data line to upstream USB host controller with high-bandwidth analog switch (925 MHz bandwidth, 2-6 Ω on-resistance)."+      },+      {+        "number": "3",+        "name": "DP_OUT",+        "type": "bidirectional",+        "description": "D+ data line to upstream USB host controller with high-bandwidth analog switch (925 MHz bandwidth, 2-6 Ω on-resistance)."+      },+      {+        "number": "4",+        "name": "CS",+        "type": "output",+        "description": "Current-sink output providing proportional feedback (75 µA/A) proportional to OUT load current for cable-compensation loop."+      },+      {+        "number": "5",+        "name": "EN",+        "type": "input",+        "description": "Active-high logic input enabling power and signal switches (1.35 V rising threshold, 200 mV hysteresis); device enters UVLO at 4.1 V."+      },+      {+        "number": "6",+        "name": "CTL1",+        "type": "input",+        "description": "Logic-level control input for charging mode selection; tie directly to IN or GND without pullup or pulldown resistor."+      },+      {+        "number": "7",+        "name": "CTL2",+        "type": "input",+        "description": "Logic-level control input for charging mode selection; tie directly to IN or GND without pullup or pulldown resistor."+      },+      {+        "number": "8",+        "name": "CTL3",+        "type": "input",+        "description": "Logic-level control input for charging mode selection; tie directly to IN or GND without pullup or pulldown resistor."+      },+      {+        "number": "9",+        "name": "STATUS",+        "type": "tri_state",+        "description": "Active-low open-drain output asserts when load exceeds load-detection threshold (700 mA typical with 80.6 kΩ ILIM_LO resistor, 210 ms response time)."+      },+      {+        "number": "10",+        "name": "DP_IN",+        "type": "bidirectional",+        "description": "D+ data line from downstream connector with ESD protection (±8 kV contact discharge, ±15 kV air discharge per IEC 61000-4-2) and short-to-VBUS overvoltage protection (3.9 V trip threshold)."+      },+      {+        "number": "11",+        "name": "DM_IN",+        "type": "bidirectional",+        "description": "D- data line from downstream connector with ESD protection (±8 kV contact discharge, ±15 kV air discharge per IEC 61000-4-2) and short-to-VBUS overvoltage protection (3.9 V trip threshold)."+      },+      {+        "number": "12",+        "name": "OUT",+        "type": "power_out",+        "description": "Power-switch output with maximum continuous current 3.2 A and on-resistance 47 mΩ typical (47-80 mΩ over -40°C to 125°C)."+      },+      {+        "number": "13",+        "name": "FAULT",+        "type": "tri_state",+        "description": "Active-low open-drain output asserts on overtemperature (>155°C or >135°C in current-limit mode), overcurrent (>programmed IOS), or DP_IN/DM_IN overvoltage (>3.9 V) with 8 ms deglitch."+      },+      {+        "number": "14",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection; thermal pad internally connected to GND and must be soldered to PCB ground plane."+      },+      {+        "number": "15",+        "name": "ILIM_LO",+        "type": "input",+        "description": "Low current-limit setting input; connect external resistor to GND to program threshold using I(OS) = 53762 / [R(ILIM_LO) × 1.0021], range 10.4-1000 kΩ."+      },+      {+        "number": "16",+        "name": "ILIM_HI",+        "type": "input",+        "description": "High current-limit setting input; connect external resistor to GND to program threshold using I(OS) = 53762 / [R(ILIM_HI) × 1.0021], range 10.4-1000 kΩ."+      },+      {+        "number": "17",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 17 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 46,+        "cost_usd": 0.4378,+        "at": "2026-09-18T01:06:36"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps2549-q1",+        "pages": 46,+        "sha256": "4d8861e6d954954c",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file