← Commit history

Initial commit: component/tps24770rget

Ray ·feb1ce9e83 ·
2 files changed +307
README.mdadded+62
@@ -0,0 +1,62 @@+# TPS24770RGET++**Texas Instruments** · Supervisor And Reset ICs · VQFN-24-EP(4x4)++TPS24770RGET from Texas Instruments, in a VQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | NC | unconnected | No connect. Tie to ground or leave floating. |+| 2 | ENHS | input | Active-high enable input of Hot Swap. Logic input connects to resistor divider. |+| 3 | NC | unconnected | No connect. Tie to ground or leave floating. |+| 4 | FLTb | output | Active-low, open-drain output indicating various faults. |+| 5 | PGHS | output | Active-high, open-drain power-good indicator. |+| 6 | NC | unconnected | No connect. Tie to ground or leave floating. |+| 7 | TINR | bidirectional | Inrush timer, which runs during the inrush operation (start-up) if the part is in current limit or power limit. |+| 8 | TFLT | bidirectional | Fault timer, which runs when the device is in regular operation and there is an overcurrent condition. |+| 9 | OV | input | Overvoltage comparator input connects to resistor divider; HGATE pulled low when OV exceeds threshold or connect to ground when not used. |+| 10 | GND | power_in | Ground. |+| 11 | PLIM | input | Power limit programming pin; resistor from this pin to GND sets maximum power dissipation for Hot Swap FET, or connect 4.99 kΩ resistor to disable power limit. |+| 12 | IMON | bidirectional | Analog monitor and current limit program point; connect RIMON to ground. |+| 13 | IMONBUF | output | Voltage output proportional to the load current with range 0V-3.0V. |+| 14 | VDD | power_in | Power Supply input, 2.5V to 18V. |+| 15 | SET | input | Current-limit programming set pin for Hot Swap; resistor connected from positive terminal of the sensing resistor. |+| 16 | FSTP | input | Fast trip programming set pin for Hot Swap; resistor connected from positive terminal of RSNS to FSTP. |+| 17 | SENM | input | Current-sensing input for the sense resistor; directly connects to the negative terminal of the sense resistor. |+| 18 | HGATE | output | Gate driver output for external Hot Swap MOSFET. |+| 19 | OUTH | input | Output voltage sensor for monitoring Hot Swap MOSFET's power; connects to the source terminal of the Hot Swap N channel MOSFET. |+| 20 | NC | unconnected | No connect. Tie to ground or leave floating. |+| 21 | NC | unconnected | No connect. Tie to ground or leave floating. |+| 22 | NC | unconnected | No connect. Tie to ground or leave floating. |+| 23 | NC | unconnected | No connect. Tie to ground or leave floating. |+| 24 | NC | unconnected | No connect. Tie to ground or leave floating. |+| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | VQFN-24-EP(4x4) |+| Category | Power Management (PMIC) |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `TPS24770RGET`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`+- 3D model: VQFN-24-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `tps24770rget-etched.step` / `tps24770rget-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps24770rget.step` / `tps24770rget.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tps24772) (50 pp, sha256 `42cf67c48c156f8e`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps24770rget-datasheet.pdf)
page.jsonadded+245
@@ -0,0 +1,245 @@+{+  "slug": "tps24770rget",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Supervisor And Reset ICs, VQFN-24-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "tps24770rget",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tps24770rget.kicad_sym",+    "tps24770rget.kicad_mod",+    "tps24770rget.glb",+    "tps24770rget.step",+    "tps24770rget.lbr",+    "docs/hero.png",+    "docs/tps24770rget-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPS24770RGET",+    "manufacturer": "Texas Instruments",+    "package": "VQFN-24-EP(4x4)",+    "pin_count": 25,+    "category": "Power Management (PMIC)",+    "subcategory": "Supervisor And Reset ICs",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tps24772",+    "parts": {+      "symbol": "tps24770rget.kicad_sym",+      "footprint": "tps24770rget.kicad_mod",+      "model_3d": "tps24770rget-etched.glb",+      "model_3d_plain": "tps24770rget.glb",+      "model_3d_step": "tps24770rget-etched.step",+      "model_3d_step_plain": "tps24770rget.step",+      "lbr": "tps24770rget.lbr"+    },+    "distributor_links": {+      "lcsc": "C2653605"+    },+    "pins": [+      {+        "number": "1",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect. Tie to ground or leave floating."+      },+      {+        "number": "2",+        "name": "ENHS",+        "type": "input",+        "description": "Active-high enable input of Hot Swap. Logic input connects to resistor divider."+      },+      {+        "number": "3",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect. Tie to ground or leave floating."+      },+      {+        "number": "4",+        "name": "FLTb",+        "type": "output",+        "description": "Active-low, open-drain output indicating various faults."+      },+      {+        "number": "5",+        "name": "PGHS",+        "type": "output",+        "description": "Active-high, open-drain power-good indicator."+      },+      {+        "number": "6",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect. Tie to ground or leave floating."+      },+      {+        "number": "7",+        "name": "TINR",+        "type": "bidirectional",+        "description": "Inrush timer, which runs during the inrush operation (start-up) if the part is in current limit or power limit."+      },+      {+        "number": "8",+        "name": "TFLT",+        "type": "bidirectional",+        "description": "Fault timer, which runs when the device is in regular operation and there is an overcurrent condition."+      },+      {+        "number": "9",+        "name": "OV",+        "type": "input",+        "description": "Overvoltage comparator input connects to resistor divider; HGATE pulled low when OV exceeds threshold or connect to ground when not used."+      },+      {+        "number": "10",+        "name": "GND",+        "type": "power_in",+        "description": "Ground."+      },+      {+        "number": "11",+        "name": "PLIM",+        "type": "input",+        "description": "Power limit programming pin; resistor from this pin to GND sets maximum power dissipation for Hot Swap FET, or connect 4.99 kΩ resistor to disable power limit."+      },+      {+        "number": "12",+        "name": "IMON",+        "type": "bidirectional",+        "description": "Analog monitor and current limit program point; connect RIMON to ground."+      },+      {+        "number": "13",+        "name": "IMONBUF",+        "type": "output",+        "description": "Voltage output proportional to the load current with range 0V-3.0V."+      },+      {+        "number": "14",+        "name": "VDD",+        "type": "power_in",+        "description": "Power Supply input, 2.5V to 18V."+      },+      {+        "number": "15",+        "name": "SET",+        "type": "input",+        "description": "Current-limit programming set pin for Hot Swap; resistor connected from positive terminal of the sensing resistor."+      },+      {+        "number": "16",+        "name": "FSTP",+        "type": "input",+        "description": "Fast trip programming set pin for Hot Swap; resistor connected from positive terminal of RSNS to FSTP."+      },+      {+        "number": "17",+        "name": "SENM",+        "type": "input",+        "description": "Current-sensing input for the sense resistor; directly connects to the negative terminal of the sense resistor."+      },+      {+        "number": "18",+        "name": "HGATE",+        "type": "output",+        "description": "Gate driver output for external Hot Swap MOSFET."+      },+      {+        "number": "19",+        "name": "OUTH",+        "type": "input",+        "description": "Output voltage sensor for monitoring Hot Swap MOSFET's power; connects to the source terminal of the Hot Swap N channel MOSFET."+      },+      {+        "number": "20",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect. Tie to ground or leave floating."+      },+      {+        "number": "21",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect. Tie to ground or leave floating."+      },+      {+        "number": "22",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect. Tie to ground or leave floating."+      },+      {+        "number": "23",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect. Tie to ground or leave floating."+      },+      {+        "number": "24",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect. Tie to ground or leave floating."+      },+      {+        "number": "25",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 25 added from the footprint"+        ],+        "pages_sent": 50,+        "cost_usd": 0.5406,+        "at": "2026-09-23T13:41:58"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tps24772",+        "pages": 50,+        "sha256": "42cf67c48c156f8e",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file