component
TPS2419PW
Public Made by Adomby adom
Texas Instruments Monitors & Reset Circuits, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+44@@ -0,0 +1,44 @@+# TPS2419PW++**Texas Instruments** · Monitors & Reset Circuits · TSSOP-8++TPS2419PW from Texas Instruments, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | RSET | input | Connect a resistor to ground to program the turn-off threshold; leaving RSET open results in a slightly positive V(A-C) turn-off threshold. |+| 2 | EN | input | Pull EN above 1.3 V to permit normal ORing operation, and a low on EN holds GATE low; EN should not be driven above its recommended maximum voltage of 5 V. |+| 3 | RSVD | power_in | This pin must be connected to GND. |+| 4 | GND | power_in | Device ground; it should have a low-impedance connection to the ground plane. |+| 5 | GATE | output | Connect to the gate of the external N-channel MOSFET to control it so it emulates a low forward-voltage diode; the absolute maximum GATE voltage is -0.3 to 30 V. |+| 6 | C | input | Voltage sense input connected to the simulated diode cathode and the bias supply for the gate-drive charge pump; it must be 3 V or greater for the external MOSFET to be turned on, with a recommended input range of 0 to 16.5 V. |+| 7 | A | input | Voltage sense input connected to the simulated diode anode and the reference for the charge-pump bias on BYP; connect to the MOSFET source in the typical configuration. |+| 8 | BYP | bidirectional | Connect a capacitor from BYP to A to filter the gate drive supply, with a 2200-pF ceramic recommended; shorting BYP to a voltage below A damages the device. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-8 |+| Category | Power Supply Chip |+| Pins | 8 |++## CAD (KiCad official)++- Symbol: `TPS2419PW`+- Footprint: `Package_SO:TSSOP-8_3x3mm_P0.65mm`+- 3D model: TSSOP-8 (KiCad packages3D, STEP)+- 3D model files: `tps2419pw-etched.step` / `tps2419pw-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tps2419pw.step` / `tps2419pw.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/tps2419.pdf) (29 pp, sha256 `5d2098bd9b468e95`, retrieved 2026-10-08, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tps2419pw-datasheet.pdf)
page.jsonadded+200@@ -0,0 +1,200 @@+{+ "slug": "tps2419pw",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments Monitors & Reset Circuits, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "tps2419pw",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "tps2419pw.kicad_sym",+ "tps2419pw.kicad_mod",+ "tps2419pw.glb",+ "tps2419pw.step",+ "tps2419pw.lbr",+ "docs/hero.png",+ "docs/tps2419pw-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "tps2419pw-hero.glb",+ "tps2419pw-hero.overlay.json"+ ],+ "component": {+ "mpn": "TPS2419PW",+ "manufacturer": "Texas Instruments",+ "package": "TSSOP-8",+ "pin_count": 8,+ "category": "Power Supply Chip",+ "subcategory": "Monitors & Reset Circuits",+ "datasheet": "https://www.ti.com/lit/ds/symlink/tps2419.pdf",+ "parts": {+ "symbol": "tps2419pw.kicad_sym",+ "footprint": "tps2419pw.kicad_mod",+ "model_3d": "tps2419pw-hero.glb",+ "model_3d_plain": "tps2419pw.glb",+ "model_3d_step": "tps2419pw-etched.step",+ "model_3d_step_plain": "tps2419pw.step",+ "lbr": "tps2419pw.lbr"+ },+ "distributor_links": {+ "lcsc": "C1524024",+ "digikey": "296-34599-5-ND",+ "mouser": "595-TPS2419PW"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T14:35:01Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-34599-5-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "595-TPS2419PW",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "RSET",+ "type": "input",+ "description": "Connect a resistor to ground to program the turn-off threshold; leaving RSET open results in a slightly positive V(A-C) turn-off threshold."+ },+ {+ "number": "2",+ "name": "EN",+ "type": "input",+ "description": "Pull EN above 1.3 V to permit normal ORing operation, and a low on EN holds GATE low; EN should not be driven above its recommended maximum voltage of 5 V."+ },+ {+ "number": "3",+ "name": "RSVD",+ "type": "power_in",+ "description": "This pin must be connected to GND."+ },+ {+ "number": "4",+ "name": "GND",+ "type": "power_in",+ "description": "Device ground; it should have a low-impedance connection to the ground plane."+ },+ {+ "number": "5",+ "name": "GATE",+ "type": "output",+ "description": "Connect to the gate of the external N-channel MOSFET to control it so it emulates a low forward-voltage diode; the absolute maximum GATE voltage is -0.3 to 30 V."+ },+ {+ "number": "6",+ "name": "C",+ "type": "input",+ "description": "Voltage sense input connected to the simulated diode cathode and the bias supply for the gate-drive charge pump; it must be 3 V or greater for the external MOSFET to be turned on, with a recommended input range of 0 to 16.5 V."+ },+ {+ "number": "7",+ "name": "A",+ "type": "input",+ "description": "Voltage sense input connected to the simulated diode anode and the reference for the charge-pump bias on BYP; connect to the MOSFET source in the typical configuration."+ },+ {+ "number": "8",+ "name": "BYP",+ "type": "bidirectional",+ "description": "Connect a capacitor from BYP to A to filter the gate drive supply, with a 2200-pF ceramic recommended; shorting BYP to a voltage below A damages the device."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The datasheet lists RSVD as type PWR and says it must be connected to GND; it is mapped to power_in ; The pinout is shown once for the PW and D packages (TOP VIEW); the TPS2419PW (TSSOP PW, 8 pins) in t; The BYP capacitor value is given as 800 to 2200 pF in the recommended conditions and 2200 pF is the "+ ],+ "pages_sent": 11,+ "cost_usd": 0.0528,+ "at": "2026-10-08T14:34:48"+ },+ "datasheet": {+ "url": "https://www.ti.com/lit/ds/symlink/tps2419.pdf",+ "pages": 29,+ "sha256": "5d2098bd9b468e95",+ "source_tier": "mfr"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 8,+ "described": 8,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "tps2419pw.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "cf28a51742b2e31065e201d1b313207140cbfb49062efd938788f7a310d02738",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "tps2419pw-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "a0d0a2425d625f6c96923d03c931d29c536606e2c8739aa3bc46a2bde7ad5a1f",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}