← Commit history

Initial commit: component/tpic8101dwr

Ray ·7f661dee7c ·
2 files changed +284
README.mdadded+56
@@ -0,0 +1,56 @@+# TPIC8101DWR++**Texas Instruments** · ADCs/DACs - Special Purpose · SOIC-20-300mil++TPIC8101DWR from Texas Instruments, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VDD | power_in | 5-V input supply with 4.7-µF external bypass capacitor required for stability of internal circuits. |+| 2 | GND | power_in | Ground connection to system ground rail. |+| 3 | Vref | power_in | Internally generated reference supply voltage with 22-nF external bypass capacitor for bias and noise decoupling. |+| 4 | OUT | output | Buffered analog integrator output for microprocessor A/D interface with 2.2-nF external stabilizing capacitor. |+| 5 | NC | unconnected | No connection; terminal reserved for test purposes only, not connected in system application. |+| 6 | NC | unconnected | No connection; terminal reserved for test purposes only, not connected in system application. |+| 7 | INT/HOLD | input | Integration/hold mode selection input (high for integrate, low for hold) with internal pulldown for default hold mode. |+| 8 | CS | input | Chip select for SPI communications, active low with internal pullup resistor for default inactive state. |+| 9 | XIN | input | Oscillator inverter input for external clock signal with 1-MΩ feedback resistor to XOUT for bias. |+| 10 | XOUT | output | Oscillator inverter output for external oscillator circuit with 1-MΩ feedback resistor to XIN. |+| 11 | SDO | tri_state | Serial data output for SPI bus with tri-state high-impedance mode when CS is pulled to VDD. |+| 12 | SDI | input | Serial data input for SPI with internal pullup to VDD and 8-bit word format data stream. |+| 13 | SCLK | input | SPI clock input with internal pullup resistor and data clocked into shift register on falling edge. |+| 14 | TEST | input | Test mode control input, active low with internal pullup to VDD (default inactive, leave open or tie high). |+| 15 | CH2P | input | Positive input for amplifier 2 interfacing to knock sensor with input range 0.05 to VDD-0.05 V. |+| 16 | CH2N | input | Negative input for amplifier 2 interfacing to knock sensor with input range 0.05 to VDD-0.05 V. |+| 17 | CH2FB | output | Feedback output of amplifier 2 for external gain-setting resistor connection with rail-to-rail compatibility. |+| 18 | CH1FB | output | Feedback output of amplifier 1 for external gain-setting resistor connection with rail-to-rail compatibility. |+| 19 | CH1N | input | Negative input for amplifier 1 interfacing to knock sensor with input range 0.05 to VDD-0.05 V. |+| 20 | CH1P | input | Positive input for amplifier 1 interfacing to knock sensor with input range 0.05 to VDD-0.05 V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | SOIC-20-300mil |+| Category | Data Acquisition |+| Pins | 20 |++## CAD (KiCad official)++- Symbol: `TPIC8101DWR`+- Footprint: `Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm`+- 3D model: SOIC-20-300mil (KiCad packages3D, STEP)+- 3D model files: `tpic8101dwr-etched.step` / `tpic8101dwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tpic8101dwr.step` / `tpic8101dwr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tpic8101) (27 pp, sha256 `6db1737f45a80b67`, retrieved 2026-09-26, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tpic8101dwr-datasheet.pdf)
page.jsonadded+228
@@ -0,0 +1,228 @@+{+  "slug": "tpic8101dwr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments ADCs/DACs - Special Purpose, SOIC-20-300mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "data acquisition",+    "tpic8101dwr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tpic8101dwr.kicad_sym",+    "tpic8101dwr.kicad_mod",+    "tpic8101dwr.glb",+    "tpic8101dwr.step",+    "tpic8101dwr.lbr",+    "docs/hero.png",+    "docs/tpic8101dwr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TPIC8101DWR",+    "manufacturer": "Texas Instruments",+    "package": "SOIC-20-300mil",+    "pin_count": 20,+    "category": "Data Acquisition",+    "subcategory": "ADCs/DACs - Special Purpose",+    "datasheet": "https://www.ti.com/cn/lit/gpn/tpic8101",+    "parts": {+      "symbol": "tpic8101dwr.kicad_sym",+      "footprint": "tpic8101dwr.kicad_mod",+      "model_3d": "tpic8101dwr-etched.glb",+      "model_3d_plain": "tpic8101dwr.glb",+      "model_3d_step": "tpic8101dwr-etched.step",+      "model_3d_step_plain": "tpic8101dwr.step",+      "lbr": "tpic8101dwr.lbr"+    },+    "distributor_links": {+      "lcsc": "C469861",+      "digikey": "296-15132-2-ND",+      "mouser": "595-TPIC8101DWR"+    },+    "distributor_check": {+      "checked_at": "2026-09-26T15:38:17Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-15132-2-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-TPIC8101DWR",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "VDD",+        "type": "power_in",+        "description": "5-V input supply with 4.7-µF external bypass capacitor required for stability of internal circuits."+      },+      {+        "number": "2",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection to system ground rail."+      },+      {+        "number": "3",+        "name": "Vref",+        "type": "power_in",+        "description": "Internally generated reference supply voltage with 22-nF external bypass capacitor for bias and noise decoupling."+      },+      {+        "number": "4",+        "name": "OUT",+        "type": "output",+        "description": "Buffered analog integrator output for microprocessor A/D interface with 2.2-nF external stabilizing capacitor."+      },+      {+        "number": "5",+        "name": "NC",+        "type": "unconnected",+        "description": "No connection; terminal reserved for test purposes only, not connected in system application."+      },+      {+        "number": "6",+        "name": "NC",+        "type": "unconnected",+        "description": "No connection; terminal reserved for test purposes only, not connected in system application."+      },+      {+        "number": "7",+        "name": "INT/HOLD",+        "type": "input",+        "description": "Integration/hold mode selection input (high for integrate, low for hold) with internal pulldown for default hold mode."+      },+      {+        "number": "8",+        "name": "CS",+        "type": "input",+        "description": "Chip select for SPI communications, active low with internal pullup resistor for default inactive state."+      },+      {+        "number": "9",+        "name": "XIN",+        "type": "input",+        "description": "Oscillator inverter input for external clock signal with 1-MΩ feedback resistor to XOUT for bias."+      },+      {+        "number": "10",+        "name": "XOUT",+        "type": "output",+        "description": "Oscillator inverter output for external oscillator circuit with 1-MΩ feedback resistor to XIN."+      },+      {+        "number": "11",+        "name": "SDO",+        "type": "tri_state",+        "description": "Serial data output for SPI bus with tri-state high-impedance mode when CS is pulled to VDD."+      },+      {+        "number": "12",+        "name": "SDI",+        "type": "input",+        "description": "Serial data input for SPI with internal pullup to VDD and 8-bit word format data stream."+      },+      {+        "number": "13",+        "name": "SCLK",+        "type": "input",+        "description": "SPI clock input with internal pullup resistor and data clocked into shift register on falling edge."+      },+      {+        "number": "14",+        "name": "TEST",+        "type": "input",+        "description": "Test mode control input, active low with internal pullup to VDD (default inactive, leave open or tie high)."+      },+      {+        "number": "15",+        "name": "CH2P",+        "type": "input",+        "description": "Positive input for amplifier 2 interfacing to knock sensor with input range 0.05 to VDD-0.05 V."+      },+      {+        "number": "16",+        "name": "CH2N",+        "type": "input",+        "description": "Negative input for amplifier 2 interfacing to knock sensor with input range 0.05 to VDD-0.05 V."+      },+      {+        "number": "17",+        "name": "CH2FB",+        "type": "output",+        "description": "Feedback output of amplifier 2 for external gain-setting resistor connection with rail-to-rail compatibility."+      },+      {+        "number": "18",+        "name": "CH1FB",+        "type": "output",+        "description": "Feedback output of amplifier 1 for external gain-setting resistor connection with rail-to-rail compatibility."+      },+      {+        "number": "19",+        "name": "CH1N",+        "type": "input",+        "description": "Negative input for amplifier 1 interfacing to knock sensor with input range 0.05 to VDD-0.05 V."+      },+      {+        "number": "20",+        "name": "CH1P",+        "type": "input",+        "description": "Positive input for amplifier 1 interfacing to knock sensor with input range 0.05 to VDD-0.05 V."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 27,+        "cost_usd": 0.2588,+        "at": "2026-09-26T15:37:58"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/tpic8101",+        "pages": 27,+        "sha256": "6db1737f45a80b67",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 20,+        "described": 20,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file