← Commit history

Initial commit: component/tmc2208-la-t

Ray ·bcfa96f209 ·
2 files changed +331
README.mdadded+64
@@ -0,0 +1,64 @@+# TMC2208-LA-T++**TRINAMIC Motion Control GmbH** · Stepper Motor Driver · QFN-28-EP(5x5)++TMC2208-LA-T from TRINAMIC Motion Control GmbH, in a QFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OB2 | output | Motor coil B output 2; open drain output stage that directly drives motor phase B terminal. |+| 2 | ENN | input | Enable not input; high level disables all motor driver bridges setting outputs to high impedance floating state. |+| 3 | GND | power_in | Ground reference; connect to GND plane with short path near pin. |+| 4 | CPO | output | Charge pump capacitor output; tie to CPI via 22nF 50V capacitor for charge pump stabilization. |+| 5 | CPI | input | Charge pump capacitor input; capacitively coupled from CPO via 22nF capacitor for charge pump feedback integration. |+| 6 | VCP | output | Charge pump voltage output; filter with 100nF capacitor tied to VS for high-side driver supply. |+| 7 | N.C. | unconnected | Unused pin; leave open or connect to GND for compatibility to future device versions. |+| 8 | 5VOUT | power_out | 5V regulator output; attach 2.2-4.7µF ceramic capacitor directly to GND near pin for filtering. |+| 9 | MS1 | input | Microstep resolution selection input with internal pull-down resistor; combined with MS2 pin for resolution setting. |+| 10 | MS2 | input | Microstep resolution selection input with internal pull-down resistor; MS2:MS1 = 00 selects 1/8, 01 selects 1/2, 10 selects 1/4, 11 selects 1/16 microsteps. |+| 11 | DIAG | output | Diagnostic output; high logic level indicates driver shutdown due to overtemperature or short circuit, reset by ENN=high. |+| 12 | INDEX | output | Configurable index output; provides pulse at microstep counter zero position indicating one electrical rotation or toggle on internal step pulses. |+| 13 | CLK | input | Clock input; tie to GND with short wire for internal 12MHz trimmed oscillator or supply external 4-18MHz clock for precise timing. |+| 14 | PDN_UART | bidirectional | Power down not control input and optional single-wire UART interface; low enables automatic standstill current reduction, or bidirectional data line when UART configured. |+| 15 | VCC_IO | power_in | Digital IO supply voltage 3.3V to 5V; provides logic levels for all digital control and signal pins. |+| 16 | STEP | input | Step pulse input; rising edge (or both edges if DEDGE enabled) increments/decrements microstep counter with selected resolution. |+| 17 | VREF | power_in | Analog reference voltage input 0-2.5V for motor current scaling; or reference current input when using internal RDSon current sensing mode. |+| 18 | GND | power_in | Ground reference; connect to GND plane with short path near pin. |+| 19 | DIR | input | Direction input with internal pull-down resistor; high level commands reverse motor rotation, low level commands forward rotation. |+| 20 | N.C. | unconnected | Unused pin; leave open or connect to GND for compatibility to future device versions. |+| 21 | OA2 | output | Motor coil A output 2; open drain output stage that directly drives motor phase A terminal. |+| 22 | VS | power_in | Motor supply voltage 4.75-36V DC; provide bulk filtering with low ESR electrolytics and short GND return path. |+| 23 | BRA | input | Sense resistor connection for coil A; place external sense resistor to GND near pin or tie to GND when using internal RDSon current sensing mode. |+| 24 | OA1 | output | Motor coil A output 1; open drain output stage that directly drives motor phase A terminal. |+| 25 | N.C. | unconnected | Unused pin; leave open or connect to GND for compatibility to future device versions. |+| 26 | OB1 | output | Motor coil B output 1; open drain output stage that directly drives motor phase B terminal. |+| 27 | BRB | input | Sense resistor connection for coil B; place external sense resistor to GND near pin or tie to GND when using internal RDSon current sensing mode. |+| 28 | VS | power_in | Motor supply voltage 4.75-36V DC; provide bulk filtering with low ESR electrolytics and short GND return path. |+| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | TRINAMIC Motion Control GmbH |+| Package | QFN-28-EP(5x5) |+| Category | Motor Driver ICs |+| Pins | 29 |++## CAD (KiCad official)++- Symbol: `TMC2208-LA-T`+- Footprint: `Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm`+- 3D model: QFN-28-EP(5x5) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [TRINAMIC Motion Control GmbH datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586182891412209664) (81 pp, sha256 `255c42856d78b0c7`, retrieved 2026-09-17, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tmc2208-la-t-datasheet.pdf)
page.jsonadded+267
@@ -0,0 +1,267 @@+{+  "slug": "tmc2208-la-t",+  "version": "0.1.0",+  "type": "component",+  "description": "TRINAMIC Motion Control GmbH Stepper Motor Driver, QFN-28-EP(5x5). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "motor driver ics",+    "tmc2208-la-t",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tmc2208-la-t.kicad_sym",+    "tmc2208-la-t.kicad_mod",+    "tmc2208-la-t.glb",+    "tmc2208-la-t.step",+    "tmc2208-la-t.lbr",+    "docs/hero.png",+    "docs/tmc2208-la-t-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TMC2208-LA-T",+    "manufacturer": "TRINAMIC Motion Control GmbH",+    "package": "QFN-28-EP(5x5)",+    "pin_count": 29,+    "category": "Motor Driver ICs",+    "subcategory": "Stepper Motor Driver",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586182891412209664",+    "parts": {+      "symbol": "tmc2208-la-t.kicad_sym",+      "footprint": "tmc2208-la-t.kicad_mod",+      "model_3d": "tmc2208-la-t.glb",+      "model_3d_step": "tmc2208-la-t.step",+      "lbr": "tmc2208-la-t.lbr"+    },+    "distributor_links": {+      "lcsc": "C115944"+    },+    "pins": [+      {+        "number": "1",+        "name": "OB2",+        "type": "output",+        "description": "Motor coil B output 2; open drain output stage that directly drives motor phase B terminal."+      },+      {+        "number": "2",+        "name": "ENN",+        "type": "input",+        "description": "Enable not input; high level disables all motor driver bridges setting outputs to high impedance floating state."+      },+      {+        "number": "3",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference; connect to GND plane with short path near pin."+      },+      {+        "number": "4",+        "name": "CPO",+        "type": "output",+        "description": "Charge pump capacitor output; tie to CPI via 22nF 50V capacitor for charge pump stabilization."+      },+      {+        "number": "5",+        "name": "CPI",+        "type": "input",+        "description": "Charge pump capacitor input; capacitively coupled from CPO via 22nF capacitor for charge pump feedback integration."+      },+      {+        "number": "6",+        "name": "VCP",+        "type": "output",+        "description": "Charge pump voltage output; filter with 100nF capacitor tied to VS for high-side driver supply."+      },+      {+        "number": "7",+        "name": "N.C.",+        "type": "unconnected",+        "description": "Unused pin; leave open or connect to GND for compatibility to future device versions."+      },+      {+        "number": "8",+        "name": "5VOUT",+        "type": "power_out",+        "description": "5V regulator output; attach 2.2-4.7µF ceramic capacitor directly to GND near pin for filtering."+      },+      {+        "number": "9",+        "name": "MS1",+        "type": "input",+        "description": "Microstep resolution selection input with internal pull-down resistor; combined with MS2 pin for resolution setting."+      },+      {+        "number": "10",+        "name": "MS2",+        "type": "input",+        "description": "Microstep resolution selection input with internal pull-down resistor; MS2:MS1 = 00 selects 1/8, 01 selects 1/2, 10 selects 1/4, 11 selects 1/16 microsteps."+      },+      {+        "number": "11",+        "name": "DIAG",+        "type": "output",+        "description": "Diagnostic output; high logic level indicates driver shutdown due to overtemperature or short circuit, reset by ENN=high."+      },+      {+        "number": "12",+        "name": "INDEX",+        "type": "output",+        "description": "Configurable index output; provides pulse at microstep counter zero position indicating one electrical rotation or toggle on internal step pulses."+      },+      {+        "number": "13",+        "name": "CLK",+        "type": "input",+        "description": "Clock input; tie to GND with short wire for internal 12MHz trimmed oscillator or supply external 4-18MHz clock for precise timing."+      },+      {+        "number": "14",+        "name": "PDN_UART",+        "type": "bidirectional",+        "description": "Power down not control input and optional single-wire UART interface; low enables automatic standstill current reduction, or bidirectional data line when UART configured."+      },+      {+        "number": "15",+        "name": "VCC_IO",+        "type": "power_in",+        "description": "Digital IO supply voltage 3.3V to 5V; provides logic levels for all digital control and signal pins."+      },+      {+        "number": "16",+        "name": "STEP",+        "type": "input",+        "description": "Step pulse input; rising edge (or both edges if DEDGE enabled) increments/decrements microstep counter with selected resolution."+      },+      {+        "number": "17",+        "name": "VREF",+        "type": "power_in",+        "description": "Analog reference voltage input 0-2.5V for motor current scaling; or reference current input when using internal RDSon current sensing mode."+      },+      {+        "number": "18",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference; connect to GND plane with short path near pin."+      },+      {+        "number": "19",+        "name": "DIR",+        "type": "input",+        "description": "Direction input with internal pull-down resistor; high level commands reverse motor rotation, low level commands forward rotation."+      },+      {+        "number": "20",+        "name": "N.C.",+        "type": "unconnected",+        "description": "Unused pin; leave open or connect to GND for compatibility to future device versions."+      },+      {+        "number": "21",+        "name": "OA2",+        "type": "output",+        "description": "Motor coil A output 2; open drain output stage that directly drives motor phase A terminal."+      },+      {+        "number": "22",+        "name": "VS",+        "type": "power_in",+        "description": "Motor supply voltage 4.75-36V DC; provide bulk filtering with low ESR electrolytics and short GND return path."+      },+      {+        "number": "23",+        "name": "BRA",+        "type": "input",+        "description": "Sense resistor connection for coil A; place external sense resistor to GND near pin or tie to GND when using internal RDSon current sensing mode."+      },+      {+        "number": "24",+        "name": "OA1",+        "type": "output",+        "description": "Motor coil A output 1; open drain output stage that directly drives motor phase A terminal."+      },+      {+        "number": "25",+        "name": "N.C.",+        "type": "unconnected",+        "description": "Unused pin; leave open or connect to GND for compatibility to future device versions."+      },+      {+        "number": "26",+        "name": "OB1",+        "type": "output",+        "description": "Motor coil B output 1; open drain output stage that directly drives motor phase B terminal."+      },+      {+        "number": "27",+        "name": "BRB",+        "type": "input",+        "description": "Sense resistor connection for coil B; place external sense resistor to GND near pin or tie to GND when using internal RDSon current sensing mode."+      },+      {+        "number": "28",+        "name": "VS",+        "type": "power_in",+        "description": "Motor supply voltage 4.75-36V DC; provide bulk filtering with low ESR electrolytics and short GND return path."+      },+      {+        "number": "29",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Exposed die pad listed in table but without discrete pin number; datasheet indicates it serves as GN",+          "exposed pad 29 added from the footprint"+        ],+        "pages_sent": 81,+        "cost_usd": 0.6338,+        "at": "2026-09-17T18:14:01"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586182891412209664",+        "pages": 81,+        "sha256": "255c42856d78b0c7",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 29,+        "described": 29,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file