← Commit history

Initial commit: component/tm1621

Ray ·b83e44c4f5 ·
2 files changed +440
README.mdadded+81
@@ -0,0 +1,81 @@+# TM1621++**TM Shenzhen Titan Micro Elec** · LCD Drivers · LQFP-44(10x10)++TM1621 from TM Shenzhen Titan Micro Elec, in a LQFP-44(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | /CS | input | Active-low chip select; logic high resets the serial interface and invalidates all data and command transfers; logic low enables read/write communication with TM1621. |+| 2 | /RD | input | Active-low read clock input; TM1621 outputs RAM data onto the DATA line on the falling edge; host controller must latch data between the rising edge and the next falling edge; max serial clock 300 kHz at 3 V, 500 kHz at 5 V. |+| 3 | DATA | bidirectional | Bidirectional serial data input/output with external pull-up to VDD (recommended 10 kΩ ±20%); carries addresses, write data, and command bytes; output propagation delay tDD ≤ 2 µs at 3 V. |+| 4 | VSS | power_in | System logic ground, 0 V reference; die substrate must also be connected to a low potential. |+| 5 | VLCD | power_in | LCD bias supply input; voltage must be lower than VDD; adjusted via external resistor divider (e.g. VR = 15 kΩ ±20% gives VLCD = 4 V when VDD = 5 V). |+| 6 | VDD | power_in | Logic positive supply, 2.4-5.2 V; operating current 150-300 µA typ at 3 V (internal RC oscillator), 300-600 µA at 5 V. |+| 7 | BZ | output | Buzzer positive audio output; differential drive pair with /BZ for piezoelectric buzzer; selectable 2 kHz or 4 kHz tone via TONE 2K/4K command; held low when tone is disabled; IOH1/IOL1 typ ±0.4/0.5 mA at 3 V. |+| 8 | /BZ | output | Buzzer complementary audio output; differential pair with BZ; held low when tone is disabled or system oscillator is off; IOH1/IOL1 typ ±0.4/0.5 mA at 3 V. |+| 9 | COM0 | output | LCD common 0 driver output; outputs multiplex waveform at up to 256 Hz with selectable 1/2 or 1/3 bias; sink current IOL2 typ 80 µA, source current IOH2 typ 80 µA at 3 V. |+| 10 | COM1 | output | LCD common 1 driver output; outputs multiplex waveform at up to 256 Hz with selectable 1/2 or 1/3 bias; sink current IOL2 typ 80 µA, source current IOH2 typ 80 µA at 3 V. |+| 11 | COM2 | output | LCD common 2 driver output; outputs multiplex waveform at up to 256 Hz with selectable 1/2 or 1/3 bias; sink current IOL2 typ 80 µA, source current IOH2 typ 80 µA at 3 V. |+| 12 | COM3 | output | LCD common 3 driver output; active only when 4-COM mode is selected via BIAS&COM command; sink current IOL2 typ 80 µA, source current IOH2 typ 80 µA at 3 V. |+| 13 | SEG31 | output | LCD segment 31 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 14 | SEG30 | output | LCD segment 30 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 15 | SEG29 | output | LCD segment 29 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 16 | SEG28 | output | LCD segment 28 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 17 | SEG27 | output | LCD segment 27 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 18 | SEG26 | output | LCD segment 26 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 19 | SEG25 | output | LCD segment 25 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 20 | SEG24 | output | LCD segment 24 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 21 | SEG23 | output | LCD segment 23 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 22 | SEG22 | output | LCD segment 22 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 23 | SEG21 | output | LCD segment 21 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 24 | SEG20 | output | LCD segment 20 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 25 | SEG19 | output | LCD segment 19 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 26 | SEG18 | output | LCD segment 18 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 27 | SEG17 | output | LCD segment 17 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 28 | SEG16 | output | LCD segment 16 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 29 | SEG15 | output | LCD segment 15 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 30 | SEG14 | output | LCD segment 14 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 31 | SEG13 | output | LCD segment 13 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 32 | SEG12 | output | LCD segment 12 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 33 | SEG11 | output | LCD segment 11 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 34 | SEG10 | output | LCD segment 10 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 35 | SEG9 | output | LCD segment 9 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 36 | SEG8 | output | LCD segment 8 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 37 | SEG7 | output | LCD segment 7 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 38 | SEG6 | output | LCD segment 6 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 39 | SEG5 | output | LCD segment 5 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 40 | SEG4 | output | LCD segment 4 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 41 | SEG3 | output | LCD segment 3 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 42 | SEG2 | output | LCD segment 2 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 43 | SEG1 | output | LCD segment 1 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |+| 44 | SEG0 | output | LCD segment 0 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | TM Shenzhen Titan Micro Elec |+| Package | LQFP-44(10x10) |+| Category | LED Drivers |+| Pins | 44 |++## CAD (KiCad official)++- Symbol: `TM1621`+- Footprint: `Package_QFP:LQFP-44_10x10mm_P0.8mm`+- 3D model: LQFP-44(10x10) (KiCad packages3D, STEP)+- 3D model files: `tm1621-etched.step` / `tm1621-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `tm1621.step` / `tm1621.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [TM Shenzhen Titan Micro Elec datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586183842159316992) (17 pp, sha256 `fdfac10dedab1e6c`, retrieved 2026-09-22, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/tm1621-datasheet.pdf)
page.jsonadded+359
@@ -0,0 +1,359 @@+{+  "slug": "tm1621",+  "version": "0.1.0",+  "type": "component",+  "description": "TM Shenzhen Titan Micro Elec LCD Drivers, LQFP-44(10x10). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "led drivers",+    "tm1621",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "tm1621.kicad_sym",+    "tm1621.kicad_mod",+    "tm1621.glb",+    "tm1621.step",+    "tm1621.lbr",+    "docs/hero.png",+    "docs/tm1621-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "TM1621",+    "manufacturer": "TM Shenzhen Titan Micro Elec",+    "package": "LQFP-44(10x10)",+    "pin_count": 44,+    "category": "LED Drivers",+    "subcategory": "LCD Drivers",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586183842159316992",+    "parts": {+      "symbol": "tm1621.kicad_sym",+      "footprint": "tm1621.kicad_mod",+      "model_3d": "tm1621-etched.glb",+      "model_3d_plain": "tm1621.glb",+      "model_3d_step": "tm1621-etched.step",+      "model_3d_step_plain": "tm1621.step",+      "lbr": "tm1621.lbr"+    },+    "distributor_links": {+      "lcsc": "C95857"+    },+    "pins": [+      {+        "number": "1",+        "name": "/CS",+        "type": "input",+        "description": "Active-low chip select; logic high resets the serial interface and invalidates all data and command transfers; logic low enables read/write communication with TM1621."+      },+      {+        "number": "2",+        "name": "/RD",+        "type": "input",+        "description": "Active-low read clock input; TM1621 outputs RAM data onto the DATA line on the falling edge; host controller must latch data between the rising edge and the next falling edge; max serial clock 300 kHz at 3 V, 500 kHz at 5 V."+      },+      {+        "number": "3",+        "name": "DATA",+        "type": "bidirectional",+        "description": "Bidirectional serial data input/output with external pull-up to VDD (recommended 10 kΩ ±20%); carries addresses, write data, and command bytes; output propagation delay tDD ≤ 2 µs at 3 V."+      },+      {+        "number": "4",+        "name": "VSS",+        "type": "power_in",+        "description": "System logic ground, 0 V reference; die substrate must also be connected to a low potential."+      },+      {+        "number": "5",+        "name": "VLCD",+        "type": "power_in",+        "description": "LCD bias supply input; voltage must be lower than VDD; adjusted via external resistor divider (e.g. VR = 15 kΩ ±20% gives VLCD = 4 V when VDD = 5 V)."+      },+      {+        "number": "6",+        "name": "VDD",+        "type": "power_in",+        "description": "Logic positive supply, 2.4-5.2 V; operating current 150-300 µA typ at 3 V (internal RC oscillator), 300-600 µA at 5 V."+      },+      {+        "number": "7",+        "name": "BZ",+        "type": "output",+        "description": "Buzzer positive audio output; differential drive pair with /BZ for piezoelectric buzzer; selectable 2 kHz or 4 kHz tone via TONE 2K/4K command; held low when tone is disabled; IOH1/IOL1 typ ±0.4/0.5 mA at 3 V."+      },+      {+        "number": "8",+        "name": "/BZ",+        "type": "output",+        "description": "Buzzer complementary audio output; differential pair with BZ; held low when tone is disabled or system oscillator is off; IOH1/IOL1 typ ±0.4/0.5 mA at 3 V."+      },+      {+        "number": "9",+        "name": "COM0",+        "type": "output",+        "description": "LCD common 0 driver output; outputs multiplex waveform at up to 256 Hz with selectable 1/2 or 1/3 bias; sink current IOL2 typ 80 µA, source current IOH2 typ 80 µA at 3 V."+      },+      {+        "number": "10",+        "name": "COM1",+        "type": "output",+        "description": "LCD common 1 driver output; outputs multiplex waveform at up to 256 Hz with selectable 1/2 or 1/3 bias; sink current IOL2 typ 80 µA, source current IOH2 typ 80 µA at 3 V."+      },+      {+        "number": "11",+        "name": "COM2",+        "type": "output",+        "description": "LCD common 2 driver output; outputs multiplex waveform at up to 256 Hz with selectable 1/2 or 1/3 bias; sink current IOL2 typ 80 µA, source current IOH2 typ 80 µA at 3 V."+      },+      {+        "number": "12",+        "name": "COM3",+        "type": "output",+        "description": "LCD common 3 driver output; active only when 4-COM mode is selected via BIAS&COM command; sink current IOL2 typ 80 µA, source current IOH2 typ 80 µA at 3 V."+      },+      {+        "number": "13",+        "name": "SEG31",+        "type": "output",+        "description": "LCD segment 31 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "14",+        "name": "SEG30",+        "type": "output",+        "description": "LCD segment 30 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "15",+        "name": "SEG29",+        "type": "output",+        "description": "LCD segment 29 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "16",+        "name": "SEG28",+        "type": "output",+        "description": "LCD segment 28 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "17",+        "name": "SEG27",+        "type": "output",+        "description": "LCD segment 27 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "18",+        "name": "SEG26",+        "type": "output",+        "description": "LCD segment 26 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "19",+        "name": "SEG25",+        "type": "output",+        "description": "LCD segment 25 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "20",+        "name": "SEG24",+        "type": "output",+        "description": "LCD segment 24 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "21",+        "name": "SEG23",+        "type": "output",+        "description": "LCD segment 23 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "22",+        "name": "SEG22",+        "type": "output",+        "description": "LCD segment 22 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "23",+        "name": "SEG21",+        "type": "output",+        "description": "LCD segment 21 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "24",+        "name": "SEG20",+        "type": "output",+        "description": "LCD segment 20 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "25",+        "name": "SEG19",+        "type": "output",+        "description": "LCD segment 19 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "26",+        "name": "SEG18",+        "type": "output",+        "description": "LCD segment 18 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "27",+        "name": "SEG17",+        "type": "output",+        "description": "LCD segment 17 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "28",+        "name": "SEG16",+        "type": "output",+        "description": "LCD segment 16 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "29",+        "name": "SEG15",+        "type": "output",+        "description": "LCD segment 15 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "30",+        "name": "SEG14",+        "type": "output",+        "description": "LCD segment 14 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "31",+        "name": "SEG13",+        "type": "output",+        "description": "LCD segment 13 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "32",+        "name": "SEG12",+        "type": "output",+        "description": "LCD segment 12 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "33",+        "name": "SEG11",+        "type": "output",+        "description": "LCD segment 11 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "34",+        "name": "SEG10",+        "type": "output",+        "description": "LCD segment 10 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "35",+        "name": "SEG9",+        "type": "output",+        "description": "LCD segment 9 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "36",+        "name": "SEG8",+        "type": "output",+        "description": "LCD segment 8 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "37",+        "name": "SEG7",+        "type": "output",+        "description": "LCD segment 7 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "38",+        "name": "SEG6",+        "type": "output",+        "description": "LCD segment 6 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "39",+        "name": "SEG5",+        "type": "output",+        "description": "LCD segment 5 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "40",+        "name": "SEG4",+        "type": "output",+        "description": "LCD segment 4 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "41",+        "name": "SEG3",+        "type": "output",+        "description": "LCD segment 3 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "42",+        "name": "SEG2",+        "type": "output",+        "description": "LCD segment 2 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "43",+        "name": "SEG1",+        "type": "output",+        "description": "LCD segment 1 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      },+      {+        "number": "44",+        "name": "SEG0",+        "type": "output",+        "description": "LCD segment 0 driver output; directly mirrors display RAM bit; sink current IOL3 typ 60 µA, source current IOH3 typ 40 µA at 3 V."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: SEG0-SEG31 pin assignment: The datasheet table lists pins 13-44 as 'SEG0~SEG31' with range notation ; LQFP44 variant differences: This package omits /WR (write control), OSCI/OSCO (oscillator connection"+        ],+        "pages_sent": 17,+        "cost_usd": 0.7515,+        "at": "2026-09-22T10:35:57"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586183842159316992",+        "pages": 17,+        "sha256": "fdfac10dedab1e6c",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 44,+        "described": 44,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file