TJ4320GDP-ADJ

@@ -26,7 +26,9 @@       "model_3d_step": "tj4320gdp-adj.step",       "lbr": "tj4320gdp-adj.lbr"     },-    "distributor_links": {},+    "distributor_links": {+      "lcsc": "C126089"+    },     "pins": [       {         "number": "1",@@ -38,13 +40,13 @@         "number": "2",         "name": "EN",         "type": "input",-        "description": "Chip enable. Pulling this pin below 0.4 V (VIL) turns the regulator off; VIH ≥ 2.0 V enables the device. Do not float. Enable input current ~0.1 µA (max 1 µA)."+        "description": "Chip enable. Pulling this pin below 0.4 V (VIL) turns the regulator off; VIH \u2265 2.0 V enables the device. Do not float. Enable input current ~0.1 \u00b5A (max 1 \u00b5A)."       },       {         "number": "3",         "name": "VIN",         "type": "power_in",-        "description": "Input supply pin. Recommended operating range 2.5 V to 5.5 V (absolute max 6.5 V). Requires a low-ESR ceramic bypass capacitor (≥10 µF recommended) placed close to the pin."+        "description": "Input supply pin. Recommended operating range 2.5 V to 5.5 V (absolute max 6.5 V). Requires a low-ESR ceramic bypass capacitor (\u226510 \u00b5F recommended) placed close to the pin."       },       {         "number": "4",@@ -56,25 +58,25 @@         "number": "5",         "name": "SS",         "type": "passive",-        "description": "Soft-start. Connect an external capacitor (CSS) between this pin and ground to set the soft-start time (e.g. 220 pF ≈ 0.23 ms, 10 nF ≈ 10.4 ms). Internal ~130 nA current source charges CSS against a ~450 kΩ / 0.6 V reference. Do not tie directly to ground."+        "description": "Soft-start. Connect an external capacitor (CSS) between this pin and ground to set the soft-start time (e.g. 220 pF \u2248 0.23 ms, 10 nF \u2248 10.4 ms). Internal ~130 nA current source charges CSS against a ~450 k\u03a9 / 0.6 V reference. Do not tie directly to ground."       },       {         "number": "6",         "name": "VOUT",         "type": "power_out",-        "description": "Regulated output voltage, up to 2 A continuous. Requires a low-ESR ceramic output capacitor (≥10 µF recommended). An auto-discharge path (~330 Ω) pulls VOUT down when EN goes low."+        "description": "Regulated output voltage, up to 2 A continuous. Requires a low-ESR ceramic output capacitor (\u226510 \u00b5F recommended). An auto-discharge path (~330 \u03a9) pulls VOUT down when EN goes low."       },       {         "number": "7",         "name": "ADJ",         "type": "input",-        "description": "Output adjust / feedback input for the adjustable version. Regulates to VADJ ≈ 0.6 V (min 0.582 V, max 0.618 V over temperature). Set VOUT with an external resistor divider using R2 = R1 × (VOUT/0.6 − 1); recommended R1 in the 1 kΩ to 100 kΩ range. A 2.2 nF to 1 µF feed-forward capacitor from VOUT to ADJ improves PSRR."+        "description": "Output adjust / feedback input for the adjustable version. Regulates to VADJ \u2248 0.6 V (min 0.582 V, max 0.618 V over temperature). Set VOUT with an external resistor divider using R2 = R1 \u00d7 (VOUT/0.6 \u2212 1); recommended R1 in the 1 k\u03a9 to 100 k\u03a9 range. A 2.2 nF to 1 \u00b5F feed-forward capacitor from VOUT to ADJ improves PSRR."       },       {         "number": "8",         "name": "GND",         "type": "power_in",-        "description": "Device ground / return. Ground pin quiescent current ~0.2 mA at 200 mA load and ~0.3 mA at 2 A load; standby current ~0.1 µA when disabled."+        "description": "Device ground / return. Ground pin quiescent current ~0.2 mA at 200 mA load and ~0.3 mA at 2 A load; standby current ~0.1 \u00b5A when disabled."       },       {         "number": "9",

@@ -63,6 +63,12 @@   <smd name="7" x="2.4975" y="0.6350" dx="1.5050" dy="0.8020" layer="1"/>   <smd name="8" x="2.4975" y="1.9050" dx="1.5050" dy="0.8020" layer="1"/>   <smd name="9" x="0.0000" y="-0.0000" dx="2.6130" dy="3.5020" layer="1"/>+  <polygon width="0.1200" layer="21">+    <vertex x="-2.5000" y="2.5750"/>+    <vertex x="-2.7400" y="2.9050"/>+    <vertex x="-2.2600" y="2.9050"/>+    <vertex x="-2.5000" y="2.5750"/>+  </polygon>   <wire x1="-2.0750" y1="2.5750" x2="2.0750" y2="2.5750" width="0.1500" layer="21"/>   <wire x1="-2.0750" y1="-2.5750" x2="2.0750" y2="-2.5750" width="0.1500" layer="21"/>   <wire x1="-1.9500" y1="1.4500" x2="-0.9500" y2="2.4500" width="0.1500" layer="51"/>@@ -72,7 +78,7 @@   <wire x1="1.9500" y1="-2.4500" x2="-1.9500" y2="-2.4500" width="0.1500" layer="51"/>   <text x="0" y="3.257" size="1.27" layer="25" align="bottom-center">&gt;NAME</text>   <text x="0" y="-3.257" size="1.27" layer="27" align="top-center">&gt;VALUE</text>-<!--adom-pin1--><polygon width="0.0500" layer="21"><vertex x="-2.5000" y="2.5750"/><vertex x="-2.7400" y="2.9050"/><vertex x="-2.2600" y="2.9050"/><vertex x="-2.5000" y="2.5750"/></polygon></package>+</package> </packages> <symbols> <symbol name="TJ4320GDP-ADJ">@@ -112,7 +118,13 @@         <connect gate="G$1" pin="ADJ" pad="7"/>         <connect gate="G$1" pin="VOUT" pad="6"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="TJ4320GDP-ADJ" constant="no"/>+          <attribute name="MANUFACTURER" value="HTC Korea TAEJIN Tech" constant="no"/>+          <attribute name="LCSC_PN" value="C126089" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>