STWD100NYWY3F

@@ -26,13 +26,15 @@       "model_3d_step": "stwd100nywy3f.step",       "lbr": "stwd100nywy3f.lbr"     },-    "distributor_links": {},+    "distributor_links": {+      "lcsc": "C46043"+    },     "pins": [       {         "number": "1",         "name": "WDO",         "type": "output",-        "description": "Active-low watchdog output. Asserted low when the internal watchdog timer expires without being cleared. Available as open-drain (requires external pull-up, e.g. 10 kΩ to a supply up to 6 V) or push-pull depending on device suffix."+        "description": "Active-low watchdog output. Asserted low when the internal watchdog timer expires without being cleared. Available as open-drain (requires external pull-up, e.g. 10 k\u03a9 to a supply up to 6 V) or push-pull depending on device suffix."       },       {         "number": "2",@@ -44,19 +46,19 @@         "number": "3",         "name": "EN",         "type": "input",-        "description": "Active-low chip enable input. When low the watchdog is enabled; when high the watchdog is disabled. Has an internal pull-down to GND, so the device is enabled if EN is left floating. Pulses ≥1 µs are detected; glitches shorter than 100 ns are ignored."+        "description": "Active-low chip enable input. When low the watchdog is enabled; when high the watchdog is disabled. Has an internal pull-down to GND, so the device is enabled if EN is left floating. Pulses \u22651 \u00b5s are detected; glitches shorter than 100 ns are ignored."       },       {         "number": "4",         "name": "WDI",         "type": "input",-        "description": "Watchdog input. Must be toggled within the watchdog timeout period tWD to clear the internal timer, otherwise WDO is asserted. Low-to-high transitions reset the timer on all versions; high-to-low transitions also reset it on STWD100xW/xX/xY. Pulses ≥1 µs are detected; glitches shorter than 100 ns are ignored."+        "description": "Watchdog input. Must be toggled within the watchdog timeout period tWD to clear the internal timer, otherwise WDO is asserted. Low-to-high transitions reset the timer on all versions; high-to-low transitions also reset it on STWD100xW/xX/xY. Pulses \u22651 \u00b5s are detected; glitches shorter than 100 ns are ignored."       },       {         "number": "5",         "name": "VCC",         "type": "power_in",-        "description": "Supply voltage input. Watchdog timer starts running once VCC rises above the startup voltage VSTART (~2.2 V). Typical operating current 13 µA."+        "description": "Supply voltage input. Watchdog timer starts running once VCC rises above the startup voltage VSTART (~2.2 V). Typical operating current 13 \u00b5A."       }     ],     "provenance": {

@@ -59,6 +59,18 @@   <smd name="3" x="-1.1375" y="-0.9500" dx="1.3250" dy="0.6000" layer="1"/>   <smd name="4" x="1.1375" y="-0.9500" dx="1.3250" dy="0.6000" layer="1"/>   <smd name="5" x="1.1375" y="0.9500" dx="1.3250" dy="0.6000" layer="1"/>+  <polygon width="0.1200" layer="21">+    <vertex x="-1.4500" y="1.5100"/>+    <vertex x="-1.6900" y="1.8400"/>+    <vertex x="-1.2100" y="1.8400"/>+  </polygon>+  <polygon width="0.1000" layer="51">+    <vertex x="-0.4000" y="1.4500"/>+    <vertex x="0.8000" y="1.4500"/>+    <vertex x="0.8000" y="-1.4500"/>+    <vertex x="-0.8000" y="-1.4500"/>+    <vertex x="-0.8000" y="1.0500"/>+  </polygon>   <wire x1="-0.9100" y1="1.5600" x2="0.9100" y2="1.5600" width="0.1200" layer="21"/>   <wire x1="-0.9100" y1="1.5100" x2="-0.9100" y2="1.5600" width="0.1200" layer="21"/>   <wire x1="-0.9100" y1="-1.5600" x2="-0.9100" y2="-1.5100" width="0.1200" layer="21"/>@@ -68,7 +80,7 @@   <wire x1="0.9100" y1="-1.5600" x2="-0.9100" y2="-1.5600" width="0.1200" layer="21"/>   <text x="0" y="2.212" size="1.27" layer="25" align="bottom-center">&gt;NAME</text>   <text x="0" y="-2.212" size="1.27" layer="27" align="top-center">&gt;VALUE</text>-<!--adom-pin1--><polygon width="0.0500" layer="21"><vertex x="-1.4500" y="1.5100"/><vertex x="-1.6900" y="1.8400"/><vertex x="-1.2100" y="1.8400"/></polygon></package>+</package> </packages> <symbols> <symbol name="STWD100NYWY3F">@@ -100,7 +112,13 @@         <connect gate="G$1" pin="VCC" pad="5"/>         <connect gate="G$1" pin="WDI" pad="4"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="STWD100NYWY3F" constant="no"/>+          <attribute name="MANUFACTURER" value="STMicroelectronics" constant="no"/>+          <attribute name="LCSC_PN" value="C46043" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>