← Commit history

Initial commit: component/stusb1600aqtr

Ray ·199922fd14 ·
2 files changed +323
README.mdadded+61
@@ -0,0 +1,61 @@+# STUSB1600AQTR++**STMicroelectronics** · Power Distribution Switches · QFN-24-EP(4x4)++STUSB1600AQTR from STMicroelectronics, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | CC1DB | input | Dead-battery enable pull-down on CC1 pin, connect to CC1 or ground for dead-battery mode support (0 to 5.5 V operating) |+| 2 | CC1 | bidirectional | Type-C configuration channel 1 for attach detection, plug orientation, and system configuration with high voltage protection up to 22 V (0 to 5.5 V operating) |+| 3 | VCONN | power_in | Power input for active cable with integrated current-limited high-side power switches; 350 mA default, programmable 100-600 mA by 50 mA steps (2.7 to 5.5 V) |+| 4 | CC2 | bidirectional | Type-C configuration channel 2 for attach detection, plug orientation, and system configuration with high voltage protection up to 22 V (0 to 5.5 V operating) |+| 5 | CC2DB | input | Dead-battery enable pull-down on CC2 pin, connect to CC2 or ground for dead-battery mode support (0 to 5.5 V operating) |+| 6 | RESET | input | Active high reset input to initialize device logic and Type-C FSM (0 to 4.5 V operating) |+| 7 | SCL | input | I²C clock input requiring external pull-up resistor; up to 400 kHz fast mode (0 to 4.5 V operating) |+| 8 | SDA | tri_state | I²C open-drain data input/output, active low with external pull-up resistor required; up to 400 kHz fast mode (0 to 4.5 V operating) |+| 9 | ALERT# | tri_state | I²C interrupt, open-drain output active low indicating status changes in monitored registers with external pull-up required (0 to 4.5 V operating) |+| 10 | GND | power_in | Ground reference (0 V) |+| 11 | VBUS_VALID | tri_state | VBUS detection open-drain output, active low when VBUS voltage is within valid operating range; external pull-up required (0 to 4.5 V operating) |+| 12 | ATTACH | tri_state | Attachment detection open-drain output, active low when valid source-to-sink connection is established or accessory detected; external pull-up required (0 to 4.5 V operating) |+| 13 | ADDR0 | input | I²C device address selection input bit; low selects address 0x28, high selects address 0x29 for two-device configurations (0 to 4.5 V operating) |+| 14 | DEBUG1 | tri_state | Debug accessory detection in sink power role, open-drain output active low asserted when in DebugAccessory.SNK state; external pull-up required (0 to 4.5 V operating) |+| 15 | DEBUG2 | tri_state | Debug accessory detection in source power role, open-drain output active low asserted in UnorientedDebugAccessory.SRC or OrientedDebugAccessory.SRC states; external pull-up required (0 to 4.5 V operating) |+| 16 | NC | unconnected | No connection; reserved floating pin |+| 17 | A_B_SIDE | tri_state | Cable orientation open-drain output for USB SuperSpeed mux control: HiZ indicates CC1 attached, 0 indicates CC2 attached; external pull-up required (0 to 4.5 V operating) |+| 18 | VBUS_SENSE | input | High voltage analog input for VBUS voltage monitoring, discharge path control, and attachment detection in valid voltage range (0 to 22 V operating, 28 V absolute maximum) |+| 19 | VBUS_EN_SNK | tri_state | VBUS sink power path enable, open-drain output active low to drive external PMOS when connection established and VBUS valid (0 to 22 V operating, 28 V absolute maximum) |+| 20 | VBUS_EN_SRC | tri_state | VBUS source power path enable, open-drain output active low to drive external PMOS when connection established and VBUS valid (0 to 22 V operating, 28 V absolute maximum) |+| 21 | VREG_1V2 | power_out | 1.2 V internal regulator output; requires 1 µF typical decoupling capacitor (0.5 µF minimum, 10 µF maximum) |+| 22 | VSYS | power_in | Low power system supply input from battery or system power supply (3.0 to 5.5 V); connect to ground if not used |+| 23 | VREG_2V7 | power_out | 2.7 V internal regulator output; requires 1 µF typical decoupling capacitor (0.5 µF minimum, 10 µF maximum) |+| 24 | VDD | power_in | Main power supply from USB VBUS for high voltage domain; supports 4.1 to 22 V operating range with 28 V absolute maximum |+| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | QFN-24-EP(4x4) |+| Category | Power Management (PMIC) |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `STUSB1600AQTR`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm`+- 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `stusb1600aqtr-etched.step` / `stusb1600aqtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stusb1600aqtr.step` / `stusb1600aqtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588918405088468992) (66 pp, sha256 `9211c19349c2e890`, retrieved 2026-09-27, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/stusb1600aqtr-datasheet.pdf)
page.jsonadded+262
@@ -0,0 +1,262 @@+{+  "slug": "stusb1600aqtr",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics Power Distribution Switches, QFN-24-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "stusb1600aqtr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "stusb1600aqtr.kicad_sym",+    "stusb1600aqtr.kicad_mod",+    "stusb1600aqtr.glb",+    "stusb1600aqtr.step",+    "stusb1600aqtr.lbr",+    "docs/hero.png",+    "docs/stusb1600aqtr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "STUSB1600AQTR",+    "manufacturer": "STMicroelectronics",+    "package": "QFN-24-EP(4x4)",+    "pin_count": 25,+    "category": "Power Management (PMIC)",+    "subcategory": "Power Distribution Switches",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588918405088468992",+    "parts": {+      "symbol": "stusb1600aqtr.kicad_sym",+      "footprint": "stusb1600aqtr.kicad_mod",+      "model_3d": "stusb1600aqtr-etched.glb",+      "model_3d_plain": "stusb1600aqtr.glb",+      "model_3d_step": "stusb1600aqtr-etched.step",+      "model_3d_step_plain": "stusb1600aqtr.step",+      "lbr": "stusb1600aqtr.lbr"+    },+    "distributor_links": {+      "lcsc": "C2156023",+      "digikey": "497-17647-2-ND",+      "mouser": "511-STUSB1600AQTR"+    },+    "distributor_check": {+      "checked_at": "2026-09-27T10:58:51Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "497-17647-2-ND",+        "status": "found",+        "lifecycle": "Obsolete"+      },+      "mouser": {+        "pn": "511-STUSB1600AQTR",+        "status": "found",+        "lifecycle": "Obsolete"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "CC1DB",+        "type": "input",+        "description": "Dead-battery enable pull-down on CC1 pin, connect to CC1 or ground for dead-battery mode support (0 to 5.5 V operating)"+      },+      {+        "number": "2",+        "name": "CC1",+        "type": "bidirectional",+        "description": "Type-C configuration channel 1 for attach detection, plug orientation, and system configuration with high voltage protection up to 22 V (0 to 5.5 V operating)"+      },+      {+        "number": "3",+        "name": "VCONN",+        "type": "power_in",+        "description": "Power input for active cable with integrated current-limited high-side power switches; 350 mA default, programmable 100-600 mA by 50 mA steps (2.7 to 5.5 V)"+      },+      {+        "number": "4",+        "name": "CC2",+        "type": "bidirectional",+        "description": "Type-C configuration channel 2 for attach detection, plug orientation, and system configuration with high voltage protection up to 22 V (0 to 5.5 V operating)"+      },+      {+        "number": "5",+        "name": "CC2DB",+        "type": "input",+        "description": "Dead-battery enable pull-down on CC2 pin, connect to CC2 or ground for dead-battery mode support (0 to 5.5 V operating)"+      },+      {+        "number": "6",+        "name": "RESET",+        "type": "input",+        "description": "Active high reset input to initialize device logic and Type-C FSM (0 to 4.5 V operating)"+      },+      {+        "number": "7",+        "name": "SCL",+        "type": "input",+        "description": "I²C clock input requiring external pull-up resistor; up to 400 kHz fast mode (0 to 4.5 V operating)"+      },+      {+        "number": "8",+        "name": "SDA",+        "type": "tri_state",+        "description": "I²C open-drain data input/output, active low with external pull-up resistor required; up to 400 kHz fast mode (0 to 4.5 V operating)"+      },+      {+        "number": "9",+        "name": "ALERT#",+        "type": "tri_state",+        "description": "I²C interrupt, open-drain output active low indicating status changes in monitored registers with external pull-up required (0 to 4.5 V operating)"+      },+      {+        "number": "10",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference (0 V)"+      },+      {+        "number": "11",+        "name": "VBUS_VALID",+        "type": "tri_state",+        "description": "VBUS detection open-drain output, active low when VBUS voltage is within valid operating range; external pull-up required (0 to 4.5 V operating)"+      },+      {+        "number": "12",+        "name": "ATTACH",+        "type": "tri_state",+        "description": "Attachment detection open-drain output, active low when valid source-to-sink connection is established or accessory detected; external pull-up required (0 to 4.5 V operating)"+      },+      {+        "number": "13",+        "name": "ADDR0",+        "type": "input",+        "description": "I²C device address selection input bit; low selects address 0x28, high selects address 0x29 for two-device configurations (0 to 4.5 V operating)"+      },+      {+        "number": "14",+        "name": "DEBUG1",+        "type": "tri_state",+        "description": "Debug accessory detection in sink power role, open-drain output active low asserted when in DebugAccessory.SNK state; external pull-up required (0 to 4.5 V operating)"+      },+      {+        "number": "15",+        "name": "DEBUG2",+        "type": "tri_state",+        "description": "Debug accessory detection in source power role, open-drain output active low asserted in UnorientedDebugAccessory.SRC or OrientedDebugAccessory.SRC states; external pull-up required (0 to 4.5 V operating)"+      },+      {+        "number": "16",+        "name": "NC",+        "type": "unconnected",+        "description": "No connection; reserved floating pin"+      },+      {+        "number": "17",+        "name": "A_B_SIDE",+        "type": "tri_state",+        "description": "Cable orientation open-drain output for USB SuperSpeed mux control: HiZ indicates CC1 attached, 0 indicates CC2 attached; external pull-up required (0 to 4.5 V operating)"+      },+      {+        "number": "18",+        "name": "VBUS_SENSE",+        "type": "input",+        "description": "High voltage analog input for VBUS voltage monitoring, discharge path control, and attachment detection in valid voltage range (0 to 22 V operating, 28 V absolute maximum)"+      },+      {+        "number": "19",+        "name": "VBUS_EN_SNK",+        "type": "tri_state",+        "description": "VBUS sink power path enable, open-drain output active low to drive external PMOS when connection established and VBUS valid (0 to 22 V operating, 28 V absolute maximum)"+      },+      {+        "number": "20",+        "name": "VBUS_EN_SRC",+        "type": "tri_state",+        "description": "VBUS source power path enable, open-drain output active low to drive external PMOS when connection established and VBUS valid (0 to 22 V operating, 28 V absolute maximum)"+      },+      {+        "number": "21",+        "name": "VREG_1V2",+        "type": "power_out",+        "description": "1.2 V internal regulator output; requires 1 µF typical decoupling capacitor (0.5 µF minimum, 10 µF maximum)"+      },+      {+        "number": "22",+        "name": "VSYS",+        "type": "power_in",+        "description": "Low power system supply input from battery or system power supply (3.0 to 5.5 V); connect to ground if not used"+      },+      {+        "number": "23",+        "name": "VREG_2V7",+        "type": "power_out",+        "description": "2.7 V internal regulator output; requires 1 µF typical decoupling capacitor (0.5 µF minimum, 10 µF maximum)"+      },+      {+        "number": "24",+        "name": "VDD",+        "type": "power_in",+        "description": "Main power supply from USB VBUS for high voltage domain; supports 4.1 to 22 V operating range with 28 V absolute maximum"+      },+      {+        "number": "25",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 25 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 66,+        "cost_usd": 0.4679,+        "at": "2026-09-27T10:58:33"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588918405088468992",+        "pages": 66,+        "sha256": "9211c19349c2e890",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file