STM32H747BIT6

@@ -0,0 +1,244 @@+# STM32H747BIT6++**STMicroelectronics** · Microcontrollers (MCU/MPU/SOC) · LQFP-208(28x28)++STM32H747BIT6 from STMicroelectronics, in a LQFP-208(28x28). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model, then checked against ST open pin data); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | PE2 | bidirectional | 5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACECLK, SAI1_CK1, SPI4_SCK, FMC_A23 and EVENTOUT. |+| 2 | PE3 | bidirectional | 5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACED0, TIM15_BKIN, SAI1_SD_B, FMC_A19 and EVENTOUT. |+| 3 | PE4 | bidirectional | 5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACED1, SAI1_D2, SPI4_NSS, FMC_A20, DCMI_D4 and LCD_B0. |+| 4 | PE5 | bidirectional | 5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACED2, SAI1_CK2, TIM15_CH1, SPI4_MISO, FMC_A21 and LCD_G0. |+| 5 | PE6 | bidirectional | 5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACED3, TIM1_BKIN2, SAI1_D1, SPI4_MOSI, FMC_A22 and LCD_G1. |+| 6 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 7 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 8 | VBAT | power_in | Backup-domain supply pin for the RTC, LSE and backup registers, specified for 1.2 to 3.6 V. |+| 9 | PI8 | bidirectional | 5 V-tolerant I/O (FT) with alternate function EVENTOUT; also the RTC_TAMP2/WKUP3 additional function. |+| 10 | PC13 | bidirectional | 5 V-tolerant I/O (FT) with alternate function EVENTOUT; also the RTC_TAMP1/RTC_TS/WKUP2 additional function. |+| 11 | PC14-OSC32_IN | bidirectional | 5 V-tolerant I/O (FT); doubles as the 32.768 kHz oscillator input OSC32_IN, and keeps the oscillator function after reset when previously configured as an oscillator. |+| 12 | PC15-OSC32_OUT | bidirectional | 5 V-tolerant I/O (FT); doubles as the 32.768 kHz oscillator output OSC32_OUT, and keeps the oscillator function after reset when previously configured as an oscillator. |+| 13 | PI9 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include UART4_RX, FDCAN1_RX, FMC_D30, LCD_VSYNC and EVENTOUT. |+| 14 | PI10 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include FDCAN1_RXFD_MODE, ETH_MII_RX_ER, FMC_D31, LCD_HSYNC and EVENTOUT. |+| 15 | PI11 | bidirectional | 5 V-tolerant I/O (FT); alternate functions include LCD_G6, OTG_HS_ULPI_DIR and EVENTOUT, with additional function WKUP4. |+| 16 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 17 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 18 | VSSSMPS | power_in | Ground pin of the SMPS step-down converter. |+| 19 | VLXSMPS | power_out | Switching node of the SMPS step-down converter (VLXSMPS); classed as a supply pin in the datasheet pin table. |+| 20 | VDDSMPS | power_in | Supply input of the SMPS step-down converter. |+| 21 | VFBSMPS | power_in | Feedback pin of the SMPS step-down converter (VFBSMPS), classed as a supply pin in the datasheet pin table. |+| 22 | PF0 | bidirectional | 5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include I2C2_SDA and FMC_A0. |+| 23 | PF1 | bidirectional | 5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include I2C2_SCL and FMC_A1. |+| 24 | PF2 | bidirectional | 5 V-tolerant I/O (FT); alternate functions include I2C2_SMBA and FMC_A2. |+| 25 | PF3 | bidirectional | 5 V-tolerant I/O with analog option supplied by VDDA (FT_ha); alternate function FMC_A3, additional function ADC3_INP5. |+| 26 | PF4 | bidirectional | 5 V-tolerant I/O with analog option supplied by VDDA (FT_ha); alternate function FMC_A4, additional functions ADC3_INN5 and ADC3_INP9. |+| 27 | PF5 | bidirectional | 5 V-tolerant I/O with analog option supplied by VDDA (FT_ha); alternate function FMC_A5, additional function ADC3_INP4. |+| 28 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 29 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 30 | PF6 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM16_CH1, SPI5_NSS, UART7_RX and QUADSPI_BK1_IO3; additional functions ADC3_INN4 and ADC3_INP8. |+| 31 | PF7 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM17_CH1, SPI5_SCK, UART7_TX and QUADSPI_BK1_IO2; additional function ADC3_INP3. |+| 32 | PF8 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM16_CH1N, SPI5_MISO, UART7_RTS and QUADSPI_BK1_IO0; additional functions ADC3_INN3 and ADC3_INP7. |+| 33 | PF9 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM17_CH1N, SPI5_MOSI, UART7_CTS and QUADSPI_BK1_IO1; additional function ADC3_INP2. |+| 34 | PF10 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM16_BKIN, SAI1_D3, QUADSPI_CLK, DCMI_D11 and LCD_DE; additional functions ADC3_INN2 and ADC3_INP6. |+| 35 | PH0-OSC_IN | bidirectional | 5 V-tolerant I/O (FT); doubles as the HSE oscillator input OSC_IN and keeps the oscillator function after reset when previously configured as an oscillator. |+| 36 | PH1-OSC_OUT | bidirectional | 5 V-tolerant I/O (FT); doubles as the HSE oscillator output OSC_OUT and keeps the oscillator function after reset when previously configured as an oscillator. |+| 37 | NRST | bidirectional | Bidirectional reset pin with embedded weak pull-up resistor. |+| 38 | PC0 | bidirectional | 5 V-tolerant I/O with analog option supplied by VDDA (FT_a); alternate functions include DFSDM1_CKIN0, SAI2_FS_B, OTG_HS_ULPI_STP, FMC_SDNWE and LCD_R5; additional function ADC123_INP10. |+| 39 | PC1 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TRACED0, SAI1_D1, SPI2_MOSI/I2S2_SDO, ETH_MDC and MDIOS_MDC; additional functions ADC123_INN10, ADC123_INP11 and RTC_TAMP3/WKUP5. |+| 40 | PC2_C | passive | Analog pad (TT_a, 3.3 V tolerant) that is a separate pad from PC2 unless the SYSCFG analog switch is closed; additional functions ADC3_INN1 and ADC3_INP0. |+| 41 | PC3_C | passive | Analog pad (TT_a, 3.3 V tolerant) that is a separate pad from PC3 unless the SYSCFG analog switch is closed; additional function ADC3_INP1. |+| 42 | VSSA | power_in | Analog ground pin for the ADC, DAC and other analog blocks. |+| 43 | VREF+ | power_in | Positive voltage reference input for the analog peripherals (VREF+). |+| 44 | VDDA | power_in | Analog supply pin for the analog peripherals (ADC, DAC, OPAMP, comparators) and the analog I/O option. |+| 45 | PA0 | bidirectional | 5 V-tolerant I/O with analog option (FT_a); alternate functions include TIM2_CH1/TIM2_ETR, TIM5_CH1, USART2_CTS, UART4_TX and SDMMC2_CMD; additional functions ADC1_INP16 and WKUP0. |+| 46 | PA1 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM2_CH2, TIM5_CH2, LPTIM3_OUT, USART2_RTS and UART4_RX; additional functions ADC1_INN16 and ADC1_INP17. |+| 47 | PA2 | bidirectional | 5 V-tolerant I/O with analog option (FT_a); alternate functions include TIM2_CH3, TIM5_CH3, LPTIM4_OUT, USART2_TX and ETH_MDIO; additional functions ADC12_INP14 and WKUP1. |+| 48 | PH2 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include LPTIM1_IN2, QUADSPI_BK2_IO0, ETH_MII_CRS and FMC_SDCKE0; additional function ADC3_INP13. |+| 49 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 50 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 51 | PH3 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include QUADSPI_BK2_IO1, ETH_MII_COL and FMC_SDNE0; additional functions ADC3_INN13 and ADC3_INP14. |+| 52 | PH4 | bidirectional | 5 V-tolerant I/O with I2C FM+ and analog options (FT_fa); alternate functions include I2C2_SCL, LCD_G5 and OTG_HS_ULPI_NXT; additional functions ADC3_INN14 and ADC3_INP15. |+| 53 | PH5 | bidirectional | 5 V-tolerant I/O with I2C FM+ and analog options (FT_fa); alternate functions include I2C2_SDA, SPI5_NSS and FMC_SDNWE; additional functions ADC3_INN15 and ADC3_INP16. |+| 54 | PA3 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM2_CH4, TIM5_CH4, LPTIM5_OUT, USART2_RX, OTG_HS_ULPI_D0 and ETH_MII_COL; additional function ADC12_INP15. |+| 55 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 56 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 57 | PA4 | bidirectional | 3.3 V-tolerant I/O with analog option (TT_a); alternate functions include D1PWREN, SPI1_NSS/I2S1_WS, USART2_CK, DCMI_HSYNC and LCD_VSYNC; additional functions ADC12_INP18 and DAC1_OUT1. |+| 58 | PA5 | bidirectional | 3.3 V-tolerant I/O with analog option (TT_ha); alternate functions include D2PWREN, TIM2_CH1/TIM2_ETR, SPI1_SCK/I2S1_CK, OTG_HS_ULPI_CK and LCD_R4; additional functions ADC12_INN18, ADC12_INP19 and DAC1_OUT2. |+| 59 | PA6 | bidirectional | 5 V-tolerant I/O with analog option (FT_a); alternate functions include TIM1_BKIN, TIM3_CH1, SPI1_MISO/I2S1_SDI, TIM13_CH1, DCMI_PIXCLK and LCD_G2; additional function ADC12_INP3. |+| 60 | PA7 | bidirectional | 3.3 V-tolerant I/O with analog option (TT_a); alternate functions include TIM1_CH1N, TIM3_CH2, SPI1_MOSI/I2S1_SDO, ETH_MII_RX_DV/ETH_RMII_CRS_DV and FMC_SDNWE; additional functions ADC12_INN3, ADC12_INP7 and OPAMP1_VINM. |+| 61 | PC4 | bidirectional | 3.3 V-tolerant I/O with analog option (TT_a); alternate functions include C2DSLEEP, DFSDM1_CKIN2, I2S1_MCK, SPDIFRX1_IN3 and ETH_MII_RXD0; additional functions ADC12_INP4, OPAMP1_VOUT and COMP1_INM. |+| 62 | PC5 | bidirectional | 3.3 V-tolerant I/O with analog option (TT_a); alternate functions include C2SLEEP, SAI1_D3, DFSDM1_DATIN2, SPDIFRX1_IN4, FMC_SDCKE0 and COMP1_OUT; additional functions ADC12_INN4, ADC12_INP8 and OPAMP1_VINM. |+| 63 | PB0 | bidirectional | 5 V-tolerant I/O with analog option (FT_a); alternate functions include TIM1_CH2N, TIM3_CH3, TIM8_CH2N, UART4_CTS, LCD_R3, OTG_HS_ULPI_D1 and ETH_MII_RXD2; additional functions ADC12_INN5, ADC12_INP9, OPAMP1_VINP and COMP1_INP. |+| 64 | PB1 | bidirectional | 3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include TIM1_CH3N, TIM3_CH4, TIM8_CH3N, DFSDM1_DATIN1, LCD_R6, OTG_HS_ULPI_D2 and ETH_MII_RXD3; additional functions ADC12_INP5 and COMP1_INM. |+| 65 | PB2 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include RTC_OUT, SAI1_D1, DFSDM1_CKIN1, SPI3_MOSI/I2S3_SDO, QUADSPI_CLK and SAI4_D1; additional function COMP1_INP. |+| 66 | PI15 | bidirectional | 5 V-tolerant I/O (FT); alternate functions include LCD_G2, LCD_R0 and EVENTOUT. |+| 67 | PF11 | bidirectional | 5 V-tolerant I/O with analog option (FT_a); alternate functions include SPI5_MOSI, SAI2_SD_B, FMC_SDNRAS and DCMI_D12; additional function ADC1_INP2. |+| 68 | PF12 | bidirectional | 5 V-tolerant high-speed I/O with analog option (FT_ha); alternate function FMC_A6, additional functions ADC1_INN2 and ADC1_INP6. |+| 69 | PF13 | bidirectional | 5 V-tolerant high-speed I/O with analog option (FT_ha); alternate functions include DFSDM1_DATIN6, I2C4_SMBA and FMC_A7; additional function ADC2_INP2. |+| 70 | PF14 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ and analog options (FT_fha); alternate functions include DFSDM1_CKIN6, I2C4_SCL and FMC_A8; additional functions ADC2_INN2 and ADC2_INP6. |+| 71 | PF15 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include I2C4_SDA and FMC_A9. |+| 72 | PG0 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate function FMC_A10. |+| 73 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 74 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 75 | PG1 | bidirectional | 3.3 V-tolerant high-speed I/O (TT_h); alternate function FMC_A11, additional function OPAMP2_VINM. |+| 76 | PE7 | bidirectional | 3.3 V-tolerant I/O with analog option (TT_ha); alternate functions include TIM1_ETR, DFSDM1_DATIN2, UART7_RX, QUADSPI_BK2_IO0 and FMC_D4/FMC_DA4; additional functions OPAMP2_VOUT and COMP2_INM. |+| 77 | PE8 | bidirectional | 3.3 V-tolerant I/O with analog option (TT_ha); alternate functions include TIM1_CH1N, DFSDM1_CKIN2, UART7_TX, QUADSPI_BK2_IO1 and FMC_D5/FMC_DA5; additional functions COMP2_OUT and OPAMP2_VINM. |+| 78 | PE9 | bidirectional | 3.3 V-tolerant I/O with analog option (TT_ha); alternate functions include TIM1_CH1, DFSDM1_CKOUT, UART7_RTS, QUADSPI_BK2_IO2 and FMC_D6/FMC_DA6; additional functions OPAMP2_VINP and COMP2_INP. |+| 79 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 80 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 81 | PE10 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM1_CH2N, DFSDM1_DATIN4, UART7_CTS, QUADSPI_BK2_IO3 and FMC_D7/FMC_DA7; additional function COMP2_INM. |+| 82 | PE11 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM1_CH2, DFSDM1_CKIN4, SPI4_NSS, SAI2_SD_B, FMC_D8/FMC_DA8 and LCD_G3; additional function COMP2_INP. |+| 83 | PE12 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_CH3N, DFSDM1_DATIN5, SPI4_SCK, SAI2_SCK_B, FMC_D9/FMC_DA9, COMP1_OUT and LCD_B4. |+| 84 | PE13 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_CH3, DFSDM1_CKIN5, SPI4_MISO, SAI2_FS_B, FMC_D10/FMC_DA10, COMP2_OUT and LCD_DE. |+| 85 | PE14 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_CH4, SPI4_MOSI, SAI2_MCLK_B, FMC_D11/FMC_DA11 and LCD_CLK. |+| 86 | PE15 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_BKIN, FMC_D12/FMC_DA12, TIM1_BKIN_COMP12 and LCD_R7. |+| 87 | PB10 | bidirectional | 5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include TIM2_CH3, HRTIM_SCOUT, LPTIM2_IN1, I2C2_SCL, SPI2_SCK/I2S2_CK, USART3_TX, QUADSPI_BK1_NCS, OTG_HS_ULPI_D3 and ETH_MII_RX_ER. |+| 88 | PB11 | bidirectional | 5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include TIM2_CH4, HRTIM_SCIN, LPTIM2_ETR, I2C2_SDA, USART3_RX, OTG_HS_ULPI_D4, ETH_MII_TX_EN and DSI_TE. |+| 89 | VCAP | power_out | Connection for the external capacitor CEXT of the main regulator output; two VCAP pins can be used with an external capacitor. |+| 90 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 91 | VDDLDO | power_in | Supply input of the embedded LDO regulator that powers the digital circuitry; decouple with 100 nF plus 1 µF. |+| 92 | PH6 | bidirectional | 5 V-tolerant I/O (FT); alternate functions include I2C2_SMBA, SPI5_SCK, ETH_MII_RXD2, FMC_SDNE1 and DCMI_D8. |+| 93 | PH7 | bidirectional | 5 V-tolerant I/O with I2C FM+ and analog options (FT_fa); alternate functions include I2C3_SCL, SPI5_MISO, ETH_MII_RXD3, FMC_SDCKE1 and DCMI_D9. |+| 94 | PH8 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ and analog options (FT_fha); alternate functions include TIM5_ETR, I2C3_SDA, FMC_D16, DCMI_HSYNC and LCD_R2. |+| 95 | PH9 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM12_CH2, I2C3_SMBA, FMC_D17, DCMI_D0 and LCD_R3. |+| 96 | PH10 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM5_CH1, I2C4_SMBA, FMC_D18, DCMI_D1 and LCD_R4. |+| 97 | PH11 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include TIM5_CH2, I2C4_SCL, FMC_D19, DCMI_D2 and LCD_R5. |+| 98 | PH12 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include TIM5_CH3, I2C4_SDA, FMC_D20, DCMI_D3 and LCD_R6. |+| 99 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 100 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 101 | PB12 | bidirectional | 3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include TIM1_BKIN, I2C2_SMBA, SPI2_NSS/I2S2_WS, USART3_CK, FDCAN2_RX, OTG_HS_ULPI_D5, OTG_HS_ID and UART5_RX. |+| 102 | PB13 | bidirectional | 3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include TIM1_CH1N, LPTIM2_OUT, SPI2_SCK/I2S2_CK, USART3_CTS, FDCAN2_TX, OTG_HS_ULPI_D6 and UART5_TX; additional function OTG_HS_VBUS. |+| 103 | PB14 | bidirectional | 3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include TIM1_CH2N, TIM12_CH1, USART1_TX, SPI2_MISO/I2S2_SDI, USART3_RTS, UART4_RTS, SDMMC2_D0 and OTG_HS_DM. |+| 104 | PB15 | bidirectional | 3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include RTC_REFIN, TIM1_CH3N, TIM12_CH2, USART1_RX, SPI2_MOSI/I2S2_SDO, UART4_CTS, SDMMC2_D1 and OTG_HS_DP. |+| 105 | PD8 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_CKIN3, SAI3_SCK_B, USART3_TX, SPDIFRX1_IN2 and FMC_D13/FMC_DA13. |+| 106 | PD9 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_DATIN3, SAI3_SD_B, USART3_RX, FDCAN2_RXFD_MODE and FMC_D14/FMC_DA14. |+| 107 | PD10 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_CKOUT, SAI3_FS_B, USART3_CK, FDCAN2_TXFD_MODE, FMC_D15/FMC_DA15 and LCD_B3. |+| 108 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 109 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 110 | PD11 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM2_IN2, I2C4_SMBA, USART3_CTS, QUADSPI_BK1_IO0, SAI2_SD_A and FMC_A16. |+| 111 | PD12 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include LPTIM1_IN1, TIM4_CH1, LPTIM2_IN1, I2C4_SCL, USART3_RTS, QUADSPI_BK1_IO1 and FMC_A17. |+| 112 | PD13 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include LPTIM1_OUT, TIM4_CH2, I2C4_SDA, QUADSPI_BK1_IO3 and FMC_A18. |+| 113 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 114 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 115 | PD14 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM4_CH3, SAI3_MCLK_B, UART8_CTS and FMC_D0/FMC_DA0. |+| 116 | PD15 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM4_CH4, SAI3_MCLK_A, UART8_RTS/UART8_DE and FMC_D1/FMC_DA1. |+| 117 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 118 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 119 | VCAPDSI | power_out | DSI regulator capacitor pin; must be externally connected to the VDD12DSI pin. |+| 120 | VDD12DSI | power_in | 1.2 V supply pin of the DSI PHY (DSI regulator domain); must be externally connected to VCAPDSI. |+| 121 | DSI_D0P | bidirectional | MIPI DSI PHY data lane 0 positive differential pin (3.3 V-tolerant, TT). |+| 122 | DSI_D0N | bidirectional | MIPI DSI PHY data lane 0 negative differential pin (3.3 V-tolerant, TT). |+| 123 | VSSDSI | power_in | Ground pin of the DSI PHY. |+| 124 | DSI_CKP | bidirectional | MIPI DSI PHY clock lane positive differential pin (3.3 V-tolerant, TT). |+| 125 | DSI_CKN | bidirectional | MIPI DSI PHY clock lane negative differential pin (3.3 V-tolerant, TT). |+| 126 | VDD12DSI | power_in | 1.2 V supply pin of the DSI PHY (DSI regulator domain); must be externally connected to VCAPDSI. |+| 127 | DSI_D1P | bidirectional | MIPI DSI PHY data lane 1 positive differential pin (3.3 V-tolerant, TT). |+| 128 | DSI_D1N | bidirectional | MIPI DSI PHY data lane 1 negative differential pin (3.3 V-tolerant, TT). |+| 129 | VSSDSI | power_in | Ground pin of the DSI PHY. |+| 130 | PG2 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_BKIN, TIM8_BKIN_COMP12 and FMC_A12. |+| 131 | PG3 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_BKIN2, TIM8_BKIN2_COMP12 and FMC_A13. |+| 132 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 133 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 134 | PG4 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_BKIN2, TIM1_BKIN2_COMP12 and FMC_A14/FMC_BA0. |+| 135 | PG5 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_ETR and FMC_A15/FMC_BA1. |+| 136 | PG6 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM17_BKIN, HRTIM_CHE1, QUADSPI_BK1_NCS, FMC_NE3, DCMI_D12 and LCD_R7. |+| 137 | PG7 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_CHE2, SAI1_MCLK_A, USART6_CK, FMC_INT, DCMI_D13 and LCD_CLK. |+| 138 | PG8 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_ETR, SPI6_NSS, USART6_RTS, SPDIFRX1_IN3, ETH_PPS_OUT, FMC_SDCLK and LCD_G7. |+| 139 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 140 | VDD50USB | power_in | USB power input for the dedicated USB regulator that generates the 3.3 V supply for the internal USB PHYs. |+| 141 | VDD33USB | power_in | 3.3 V USB supply pin for the USB PHYs and USB I/O option; specified for 3.0 to 3.6 V. |+| 142 | PC6 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_CHA1, TIM3_CH1, TIM8_CH1, DFSDM1_CKIN3, I2S2_MCK, USART6_TX, FMC_NWAIT and DCMI_D0. |+| 143 | PC7 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TRGIO, HRTIM_CHA2, TIM3_CH2, TIM8_CH2, I2S3_MCK, USART6_RX, FMC_NE1 and DCMI_D1. |+| 144 | PC8 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED1, HRTIM_CHB1, TIM3_CH3, TIM8_CH3, USART6_CK, UART5_RTS, FMC_NE2/FMC_NCE and DCMI_D2. |+| 145 | PC9 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include MCO2, TIM3_CH4, TIM8_CH4, I2C3_SDA, I2S_CKIN, UART5_CTS, QUADSPI_BK1_IO0 and LCD_G3. |+| 146 | PA8 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ and analog options (FT_fha); alternate functions include MCO1, TIM1_CH1, HRTIM_CHB2, I2C3_SCL, USART1_CK, OTG_FS_SOF, UART7_RX, LCD_B3 and LCD_R6. |+| 147 | PA9 | bidirectional | 3.3 V-tolerant I/O with USB option supplied by VDD33USB (FT_u); alternate functions include TIM1_CH2, HRTIM_CHC1, LPUART1_TX, I2C3_SMBA, SPI2_SCK/I2S2_CK, USART1_TX, FDCAN1_RXFD_MODE, DCMI_D0 and LCD_R5; additional function OTG_FS_VBUS. |+| 148 | PA10 | bidirectional | USB-option I/O supplied by VDD33USB (FT_u); alternate functions include TIM1_CH3, HRTIM_CHC2, LPUART1_RX, USART1_RX, FDCAN1_TXFD_MODE, OTG_FS_ID, MDIOS_MDIO, DCMI_D1 and LCD_B1. |+| 149 | PA11 | bidirectional | USB-option I/O supplied by VDD33USB (FT_u); alternate functions include TIM1_CH4, HRTIM_CHD1, LPUART1_CTS, SPI2_NSS/I2S2_WS, UART4_RX, USART1_CTS, FDCAN1_RX, OTG_FS_DM and LCD_R4. |+| 150 | PA12 | bidirectional | USB-option I/O supplied by VDD33USB (FT_u); alternate functions include TIM1_ETR, HRTIM_CHD2, LPUART1_RTS, SPI2_SCK/I2S2_CK, UART4_TX, USART1_RTS, SAI2_FS_B, FDCAN1_TX, OTG_FS_DP and LCD_R5. |+| 151 | PA13 | bidirectional | 5 V-tolerant I/O (FT) multiplexed with the JTMS/SWDIO debug function; alternate function EVENTOUT. |+| 152 | VCAP | power_out | Connection for the external capacitor CEXT of the main regulator output; two VCAP pins can be used with an external capacitor. |+| 153 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 154 | VDDLDO | power_in | Supply input of the embedded LDO regulator that powers the digital circuitry; decouple with 100 nF plus 1 µF. |+| 155 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 156 | PH13 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH1N, UART4_TX, FDCAN1_TX, FMC_D21 and LCD_G2. |+| 157 | PH14 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH2N, UART4_RX, FDCAN1_RX, FMC_D22, DCMI_D4 and LCD_G3. |+| 158 | PH15 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH3N, FDCAN1_TXFD_MODE, FMC_D23, DCMI_D11 and LCD_G4. |+| 159 | PI0 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM5_CH4, SPI2_NSS/I2S2_WS, FDCAN1_RXFD_MODE, FMC_D24, DCMI_D13 and LCD_G5. |+| 160 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 161 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 162 | PI1 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_BKIN2, SPI2_SCK/I2S2_CK, TIM8_BKIN2_COMP12, FMC_D25, DCMI_D8 and LCD_G6. |+| 163 | PI2 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH4, SPI2_MISO/I2S2_SDI, FMC_D26, DCMI_D9 and LCD_G7. |+| 164 | PI3 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_ETR, SPI2_MOSI/I2S2_SDO, FMC_D27 and DCMI_D10. |+| 165 | PA14 | bidirectional | 5 V-tolerant I/O (FT) multiplexed with the JTCK/SWCLK debug function; alternate function EVENTOUT. |+| 166 | PA15 | bidirectional | 5 V-tolerant I/O (FT) multiplexed with the JTDI debug function; alternate functions include TIM2_CH1/TIM2_ETR, HRTIM_FLT1, CEC, SPI1_NSS/I2S1_WS, SPI3_NSS/I2S3_WS, SPI6_NSS, UART4_RTS, UART7_TX and DSI_TE. |+| 167 | PC10 | bidirectional | 5 V-tolerant I/O with analog option (FT_ha); alternate functions include HRTIM_EEV1, DFSDM1_CKIN5, SPI3_SCK/I2S3_CK, USART3_TX, UART4_TX, QUADSPI_BK1_IO1, SDMMC1_D2, DCMI_D8 and LCD_R2. |+| 168 | PC11 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_FLT2, DFSDM1_DATIN5, SPI3_MISO/I2S3_SDI, USART3_RX, UART4_RX, QUADSPI_BK2_NCS, SDMMC1_D3 and DCMI_D4. |+| 169 | PC12 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED3, HRTIM_EEV2, SPI3_MOSI/I2S3_SDO, USART3_CK, UART5_TX, SDMMC1_CK and DCMI_D9. |+| 170 | PD0 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_CKIN6, SAI3_SCK_A, UART4_RX, FDCAN1_RX and FMC_D2/FMC_DA2. |+| 171 | PD1 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_DATIN6, SAI3_SD_A, UART4_TX, FDCAN1_TX and FMC_D3/FMC_DA3. |+| 172 | PD2 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED2, TIM3_ETR, UART5_RX, SDMMC1_CMD and DCMI_D11. |+| 173 | PD3 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_CKOUT, SPI2_SCK/I2S2_CK, USART2_CTS, FMC_CLK, DCMI_D5 and LCD_G7. |+| 174 | PD4 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_FLT3, SAI3_FS_A, USART2_RTS, FDCAN1_RXFD_MODE and FMC_NOE. |+| 175 | PD5 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_EEV3, USART2_TX, FDCAN1_TXFD_MODE and FMC_NWE. |+| 176 | PD6 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include SAI1_D1, DFSDM1_CKIN4, DFSDM1_DATIN1, SPI3_MOSI/I2S3_SDO, USART2_RX, FDCAN2_RXFD_MODE, SDMMC2_CK, FMC_NWAIT, DCMI_D10 and LCD_B2. |+| 177 | PD7 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_DATIN4, SPI1_MOSI/I2S1_SDO, DFSDM1_CKIN1, USART2_CK, SPDIFRX1_IN0, SDMMC2_CMD and FMC_NE1. |+| 178 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 179 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 180 | PG9 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include SPI1_MISO/I2S1_SDI, USART6_RX, SPDIFRX1_IN4, QUADSPI_BK2_IO2, SAI2_FS_B, FMC_NE2/FMC_NCE and DCMI_VSYNC. |+| 181 | PG10 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_FLT5, SPI1_NSS/I2S1_WS, LCD_G3, SAI2_SD_B, FMC_NE3, DCMI_D2 and LCD_B2. |+| 182 | PG11 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM1_IN2, HRTIM_EEV4, SPI1_SCK/I2S1_CK, SPDIFRX1_IN1, SDMMC2_D2, ETH_MII_TX_EN, DCMI_D3 and LCD_B3. |+| 183 | PG12 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM1_IN1, HRTIM_EEV5, SPI6_MISO, USART6_RTS, SPDIFRX1_IN2, LCD_B4, ETH_MII_TXD1, FMC_NE4 and LCD_B1. |+| 184 | PG13 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED0, LPTIM1_OUT, HRTIM_EEV10, SPI6_SCK, USART6_CTS, ETH_MII_TXD0, FMC_A24 and LCD_R0. |+| 185 | PG14 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED1, LPTIM1_ETR, SPI6_MOSI, USART6_TX, QUADSPI_BK2_IO3, ETH_MII_TXD1, FMC_A25 and LCD_B0. |+| 186 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 187 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |+| 188 | PG15 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include USART6_CTS, FMC_SDNCAS and DCMI_D13. |+| 189 | PB3 | bidirectional | 5 V-tolerant I/O (FT) multiplexed with the JTDO/TRACESWO debug function; alternate functions include TIM2_CH2, HRTIM_FLT4, SPI1_SCK/I2S1_CK, SPI3_SCK/I2S3_CK, SPI6_SCK, SDMMC2_D2, CRS_SYNC and UART7_RX. |+| 190 | PB4 | bidirectional | 5 V-tolerant I/O (FT) multiplexed with the NJTRST debug function; alternate functions include TIM16_BKIN, TIM3_CH1, HRTIM_EEV6, SPI1_MISO/I2S1_SDI, SPI3_MISO/I2S3_SDI, SPI2_NSS/I2S2_WS, SPI6_MISO, SDMMC2_D3 and UART7_TX. |+| 191 | PB5 | bidirectional | 5 V-tolerant I/O (FT); alternate functions include TIM17_BKIN, TIM3_CH2, HRTIM_EEV7, I2C1_SMBA, SPI1_MOSI/I2S1_SDO, SPI3_MOSI/I2S3_SDO, FDCAN2_RX, OTG_HS_ULPI_D7, ETH_PPS_OUT, FMC_SDCKE1, DCMI_D10 and UART5_RX. |+| 192 | PB6 | bidirectional | 5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include TIM16_CH1N, TIM4_CH1, HRTIM_EEV8, I2C1_SCL, CEC, I2C4_SCL, USART1_TX, LPUART1_TX, FDCAN2_TX, QUADSPI_BK1_NCS, FMC_SDNE1 and DCMI_D5. |+| 193 | PB7 | bidirectional | 5 V-tolerant I/O with I2C FM+ and analog options (FT_fa); alternate functions include TIM17_CH1N, TIM4_CH2, HRTIM_EEV9, I2C1_SDA, I2C4_SDA, USART1_RX, LPUART1_RX, FMC_NL and DCMI_VSYNC; additional function PVD_IN. |+| 194 | BOOT0 | input | Dedicated BOOT0 input pin; its input voltage can go up to 9.0 V (VPP function), and it is excluded from the standard VIL/VIH I/O thresholds. |+| 195 | PB8 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include TIM16_CH1, TIM4_CH3, DFSDM1_CKIN7, I2C1_SCL, I2C4_SCL, SDMMC1_CKIN, UART4_RX, FDCAN1_RX, SDMMC2_D4, SDMMC1_D4, DCMI_D6 and LCD_B6. |+| 196 | PB9 | bidirectional | 5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include TIM17_CH1, TIM4_CH4, DFSDM1_DATIN7, I2C1_SDA, SPI2_NSS/I2S2_WS, I2C4_SDA, SDMMC1_CDIR, UART4_TX, FDCAN1_TX, SDMMC2_D5, DCMI_D7 and LCD_B7. |+| 197 | PE0 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM1_ETR, TIM4_ETR, HRTIM_SCIN, LPTIM2_ETR, UART8_RX, FDCAN1_RXFD_MODE, SAI2_MCLK_A, FMC_NBL0 and DCMI_D2. |+| 198 | PE1 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM1_IN2, HRTIM_SCOUT, UART8_TX, FDCAN1_TXFD_MODE, FMC_NBL1 and DCMI_D3. |+| 199 | VCAP | power_out | Connection for the external capacitor CEXT of the main regulator output; two VCAP pins can be used with an external capacitor. |+| 200 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 201 | PDR_ON | input | 5 V-tolerant input pin (FT) named PDR_ON, associated with the power-down reset circuitry; no further electrical limits are given in the pin table. |+| 202 | VDDLDO | power_in | Supply input of the embedded LDO regulator that powers the digital circuitry; decouple with 100 nF plus 1 µF. |+| 203 | PI4 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_BKIN, SAI2_MCLK_A, TIM8_BKIN_COMP12, FMC_NBL2, DCMI_D5 and LCD_B4. |+| 204 | PI5 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH1, SAI2_SCK_A, FMC_NBL3, DCMI_VSYNC and LCD_B5. |+| 205 | PI6 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH2, SAI2_SD_A, FMC_D28, DCMI_D6 and LCD_B6. |+| 206 | PI7 | bidirectional | 5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH3, SAI2_FS_A, FMC_D29, DCMI_D7 and LCD_B7. |+| 207 | VSS | power_in | Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV. |+| 208 | VDD | power_in | Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | LQFP-208(28x28) |+| Category | Embedded Processors & Controllers |+| Pins | 208 |++## CAD (KiCad official)++- Symbol: `STM32H747BIT6`+- Footprint: `Package_QFP:LQFP-208_28x28mm_P0.5mm`+- 3D model: LQFP-208(28x28) (KiCad packages3D, STEP)+- 3D model files: `stm32h747bit6-etched.step` / `stm32h747bit6-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `stm32h747bit6.step` / `stm32h747bit6.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588886236752982016) (252 pp, sha256 `b96e900fb695da6c`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/stm32h747bit6-datasheet.pdf)

@@ -0,0 +1,1400 @@+{+  "slug": "stm32h747bit6",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics Microcontrollers (MCU/MPU/SOC), LQFP-208(28x28). Pinout checked against ST's open pin data, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "embedded processors & controllers",+    "stm32h747bit6",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "stm32h747bit6.kicad_sym",+    "stm32h747bit6.kicad_mod",+    "stm32h747bit6.glb",+    "stm32h747bit6.step",+    "stm32h747bit6.lbr",+    "docs/hero.png",+    "docs/stm32h747bit6-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html",+    "stm32h747bit6-hero.glb",+    "stm32h747bit6-hero.overlay.json"+  ],+  "component": {+    "mpn": "STM32H747BIT6",+    "manufacturer": "STMicroelectronics",+    "package": "LQFP-208(28x28)",+    "pin_count": 208,+    "category": "Embedded Processors & Controllers",+    "subcategory": "Microcontrollers (MCU/MPU/SOC)",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588886236752982016",+    "parts": {+      "symbol": "stm32h747bit6.kicad_sym",+      "footprint": "stm32h747bit6.kicad_mod",+      "model_3d": "stm32h747bit6-hero.glb",+      "model_3d_plain": "stm32h747bit6.glb",+      "model_3d_step": "stm32h747bit6-etched.step",+      "model_3d_step_plain": "stm32h747bit6.step",+      "lbr": "stm32h747bit6.lbr"+    },+    "distributor_links": {+      "lcsc": "C730197",+      "digikey": "STM32H747BIT6-ND",+      "mouser": "511-STM32H747BIT6"+    },+    "distributor_check": {+      "checked_at": "2026-10-08T20:01:21Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "STM32H747BIT6-ND",+        "status": "found"+      },+      "mouser": {+        "pn": "511-STM32H747BIT6",+        "status": "found",+        "lifecycle": "End of Life"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "PE2",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACECLK, SAI1_CK1, SPI4_SCK, FMC_A23 and EVENTOUT."+      },+      {+        "number": "2",+        "name": "PE3",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACED0, TIM15_BKIN, SAI1_SD_B, FMC_A19 and EVENTOUT."+      },+      {+        "number": "3",+        "name": "PE4",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACED1, SAI1_D2, SPI4_NSS, FMC_A20, DCMI_D4 and LCD_B0."+      },+      {+        "number": "4",+        "name": "PE5",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACED2, SAI1_CK2, TIM15_CH1, SPI4_MISO, FMC_A21 and LCD_G0."+      },+      {+        "number": "5",+        "name": "PE6",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed low-voltage I/O (FT_h); alternate functions include TRACED3, TIM1_BKIN2, SAI1_D1, SPI4_MOSI, FMC_A22 and LCD_G1."+      },+      {+        "number": "6",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "7",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "8",+        "name": "VBAT",+        "type": "power_in",+        "description": "Backup-domain supply pin for the RTC, LSE and backup registers, specified for 1.2 to 3.6 V."+      },+      {+        "number": "9",+        "name": "PI8",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT) with alternate function EVENTOUT; also the RTC_TAMP2/WKUP3 additional function."+      },+      {+        "number": "10",+        "name": "PC13",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT) with alternate function EVENTOUT; also the RTC_TAMP1/RTC_TS/WKUP2 additional function."+      },+      {+        "number": "11",+        "name": "PC14-OSC32_IN",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT); doubles as the 32.768 kHz oscillator input OSC32_IN, and keeps the oscillator function after reset when previously configured as an oscillator."+      },+      {+        "number": "12",+        "name": "PC15-OSC32_OUT",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT); doubles as the 32.768 kHz oscillator output OSC32_OUT, and keeps the oscillator function after reset when previously configured as an oscillator."+      },+      {+        "number": "13",+        "name": "PI9",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include UART4_RX, FDCAN1_RX, FMC_D30, LCD_VSYNC and EVENTOUT."+      },+      {+        "number": "14",+        "name": "PI10",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include FDCAN1_RXFD_MODE, ETH_MII_RX_ER, FMC_D31, LCD_HSYNC and EVENTOUT."+      },+      {+        "number": "15",+        "name": "PI11",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT); alternate functions include LCD_G6, OTG_HS_ULPI_DIR and EVENTOUT, with additional function WKUP4."+      },+      {+        "number": "16",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "17",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "18",+        "name": "VSSSMPS",+        "type": "power_in",+        "description": "Ground pin of the SMPS step-down converter."+      },+      {+        "number": "19",+        "name": "VLXSMPS",+        "type": "power_out",+        "description": "Switching node of the SMPS step-down converter (VLXSMPS); classed as a supply pin in the datasheet pin table."+      },+      {+        "number": "20",+        "name": "VDDSMPS",+        "type": "power_in",+        "description": "Supply input of the SMPS step-down converter."+      },+      {+        "number": "21",+        "name": "VFBSMPS",+        "type": "power_in",+        "description": "Feedback pin of the SMPS step-down converter (VFBSMPS), classed as a supply pin in the datasheet pin table."+      },+      {+        "number": "22",+        "name": "PF0",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include I2C2_SDA and FMC_A0."+      },+      {+        "number": "23",+        "name": "PF1",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include I2C2_SCL and FMC_A1."+      },+      {+        "number": "24",+        "name": "PF2",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT); alternate functions include I2C2_SMBA and FMC_A2."+      },+      {+        "number": "25",+        "name": "PF3",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option supplied by VDDA (FT_ha); alternate function FMC_A3, additional function ADC3_INP5."+      },+      {+        "number": "26",+        "name": "PF4",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option supplied by VDDA (FT_ha); alternate function FMC_A4, additional functions ADC3_INN5 and ADC3_INP9."+      },+      {+        "number": "27",+        "name": "PF5",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option supplied by VDDA (FT_ha); alternate function FMC_A5, additional function ADC3_INP4."+      },+      {+        "number": "28",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "29",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "30",+        "name": "PF6",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM16_CH1, SPI5_NSS, UART7_RX and QUADSPI_BK1_IO3; additional functions ADC3_INN4 and ADC3_INP8."+      },+      {+        "number": "31",+        "name": "PF7",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM17_CH1, SPI5_SCK, UART7_TX and QUADSPI_BK1_IO2; additional function ADC3_INP3."+      },+      {+        "number": "32",+        "name": "PF8",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM16_CH1N, SPI5_MISO, UART7_RTS and QUADSPI_BK1_IO0; additional functions ADC3_INN3 and ADC3_INP7."+      },+      {+        "number": "33",+        "name": "PF9",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM17_CH1N, SPI5_MOSI, UART7_CTS and QUADSPI_BK1_IO1; additional function ADC3_INP2."+      },+      {+        "number": "34",+        "name": "PF10",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM16_BKIN, SAI1_D3, QUADSPI_CLK, DCMI_D11 and LCD_DE; additional functions ADC3_INN2 and ADC3_INP6."+      },+      {+        "number": "35",+        "name": "PH0-OSC_IN",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT); doubles as the HSE oscillator input OSC_IN and keeps the oscillator function after reset when previously configured as an oscillator."+      },+      {+        "number": "36",+        "name": "PH1-OSC_OUT",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT); doubles as the HSE oscillator output OSC_OUT and keeps the oscillator function after reset when previously configured as an oscillator."+      },+      {+        "number": "37",+        "name": "NRST",+        "type": "bidirectional",+        "description": "Bidirectional reset pin with embedded weak pull-up resistor."+      },+      {+        "number": "38",+        "name": "PC0",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option supplied by VDDA (FT_a); alternate functions include DFSDM1_CKIN0, SAI2_FS_B, OTG_HS_ULPI_STP, FMC_SDNWE and LCD_R5; additional function ADC123_INP10."+      },+      {+        "number": "39",+        "name": "PC1",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TRACED0, SAI1_D1, SPI2_MOSI/I2S2_SDO, ETH_MDC and MDIOS_MDC; additional functions ADC123_INN10, ADC123_INP11 and RTC_TAMP3/WKUP5."+      },+      {+        "number": "40",+        "name": "PC2_C",+        "type": "passive",+        "description": "Analog pad (TT_a, 3.3 V tolerant) that is a separate pad from PC2 unless the SYSCFG analog switch is closed; additional functions ADC3_INN1 and ADC3_INP0."+      },+      {+        "number": "41",+        "name": "PC3_C",+        "type": "passive",+        "description": "Analog pad (TT_a, 3.3 V tolerant) that is a separate pad from PC3 unless the SYSCFG analog switch is closed; additional function ADC3_INP1."+      },+      {+        "number": "42",+        "name": "VSSA",+        "type": "power_in",+        "description": "Analog ground pin for the ADC, DAC and other analog blocks."+      },+      {+        "number": "43",+        "name": "VREF+",+        "type": "power_in",+        "description": "Positive voltage reference input for the analog peripherals (VREF+)."+      },+      {+        "number": "44",+        "name": "VDDA",+        "type": "power_in",+        "description": "Analog supply pin for the analog peripherals (ADC, DAC, OPAMP, comparators) and the analog I/O option."+      },+      {+        "number": "45",+        "name": "PA0",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_a); alternate functions include TIM2_CH1/TIM2_ETR, TIM5_CH1, USART2_CTS, UART4_TX and SDMMC2_CMD; additional functions ADC1_INP16 and WKUP0."+      },+      {+        "number": "46",+        "name": "PA1",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM2_CH2, TIM5_CH2, LPTIM3_OUT, USART2_RTS and UART4_RX; additional functions ADC1_INN16 and ADC1_INP17."+      },+      {+        "number": "47",+        "name": "PA2",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_a); alternate functions include TIM2_CH3, TIM5_CH3, LPTIM4_OUT, USART2_TX and ETH_MDIO; additional functions ADC12_INP14 and WKUP1."+      },+      {+        "number": "48",+        "name": "PH2",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include LPTIM1_IN2, QUADSPI_BK2_IO0, ETH_MII_CRS and FMC_SDCKE0; additional function ADC3_INP13."+      },+      {+        "number": "49",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "50",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "51",+        "name": "PH3",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include QUADSPI_BK2_IO1, ETH_MII_COL and FMC_SDNE0; additional functions ADC3_INN13 and ADC3_INP14."+      },+      {+        "number": "52",+        "name": "PH4",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with I2C FM+ and analog options (FT_fa); alternate functions include I2C2_SCL, LCD_G5 and OTG_HS_ULPI_NXT; additional functions ADC3_INN14 and ADC3_INP15."+      },+      {+        "number": "53",+        "name": "PH5",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with I2C FM+ and analog options (FT_fa); alternate functions include I2C2_SDA, SPI5_NSS and FMC_SDNWE; additional functions ADC3_INN15 and ADC3_INP16."+      },+      {+        "number": "54",+        "name": "PA3",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM2_CH4, TIM5_CH4, LPTIM5_OUT, USART2_RX, OTG_HS_ULPI_D0 and ETH_MII_COL; additional function ADC12_INP15."+      },+      {+        "number": "55",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "56",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "57",+        "name": "PA4",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with analog option (TT_a); alternate functions include D1PWREN, SPI1_NSS/I2S1_WS, USART2_CK, DCMI_HSYNC and LCD_VSYNC; additional functions ADC12_INP18 and DAC1_OUT1."+      },+      {+        "number": "58",+        "name": "PA5",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with analog option (TT_ha); alternate functions include D2PWREN, TIM2_CH1/TIM2_ETR, SPI1_SCK/I2S1_CK, OTG_HS_ULPI_CK and LCD_R4; additional functions ADC12_INN18, ADC12_INP19 and DAC1_OUT2."+      },+      {+        "number": "59",+        "name": "PA6",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_a); alternate functions include TIM1_BKIN, TIM3_CH1, SPI1_MISO/I2S1_SDI, TIM13_CH1, DCMI_PIXCLK and LCD_G2; additional function ADC12_INP3."+      },+      {+        "number": "60",+        "name": "PA7",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with analog option (TT_a); alternate functions include TIM1_CH1N, TIM3_CH2, SPI1_MOSI/I2S1_SDO, ETH_MII_RX_DV/ETH_RMII_CRS_DV and FMC_SDNWE; additional functions ADC12_INN3, ADC12_INP7 and OPAMP1_VINM."+      },+      {+        "number": "61",+        "name": "PC4",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with analog option (TT_a); alternate functions include C2DSLEEP, DFSDM1_CKIN2, I2S1_MCK, SPDIFRX1_IN3 and ETH_MII_RXD0; additional functions ADC12_INP4, OPAMP1_VOUT and COMP1_INM."+      },+      {+        "number": "62",+        "name": "PC5",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with analog option (TT_a); alternate functions include C2SLEEP, SAI1_D3, DFSDM1_DATIN2, SPDIFRX1_IN4, FMC_SDCKE0 and COMP1_OUT; additional functions ADC12_INN4, ADC12_INP8 and OPAMP1_VINM."+      },+      {+        "number": "63",+        "name": "PB0",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_a); alternate functions include TIM1_CH2N, TIM3_CH3, TIM8_CH2N, UART4_CTS, LCD_R3, OTG_HS_ULPI_D1 and ETH_MII_RXD2; additional functions ADC12_INN5, ADC12_INP9, OPAMP1_VINP and COMP1_INP."+      },+      {+        "number": "64",+        "name": "PB1",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include TIM1_CH3N, TIM3_CH4, TIM8_CH3N, DFSDM1_DATIN1, LCD_R6, OTG_HS_ULPI_D2 and ETH_MII_RXD3; additional functions ADC12_INP5 and COMP1_INM."+      },+      {+        "number": "65",+        "name": "PB2",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include RTC_OUT, SAI1_D1, DFSDM1_CKIN1, SPI3_MOSI/I2S3_SDO, QUADSPI_CLK and SAI4_D1; additional function COMP1_INP."+      },+      {+        "number": "66",+        "name": "PI15",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT); alternate functions include LCD_G2, LCD_R0 and EVENTOUT."+      },+      {+        "number": "67",+        "name": "PF11",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_a); alternate functions include SPI5_MOSI, SAI2_SD_B, FMC_SDNRAS and DCMI_D12; additional function ADC1_INP2."+      },+      {+        "number": "68",+        "name": "PF12",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with analog option (FT_ha); alternate function FMC_A6, additional functions ADC1_INN2 and ADC1_INP6."+      },+      {+        "number": "69",+        "name": "PF13",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with analog option (FT_ha); alternate functions include DFSDM1_DATIN6, I2C4_SMBA and FMC_A7; additional function ADC2_INP2."+      },+      {+        "number": "70",+        "name": "PF14",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ and analog options (FT_fha); alternate functions include DFSDM1_CKIN6, I2C4_SCL and FMC_A8; additional functions ADC2_INN2 and ADC2_INP6."+      },+      {+        "number": "71",+        "name": "PF15",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include I2C4_SDA and FMC_A9."+      },+      {+        "number": "72",+        "name": "PG0",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate function FMC_A10."+      },+      {+        "number": "73",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "74",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "75",+        "name": "PG1",+        "type": "bidirectional",+        "description": "3.3 V-tolerant high-speed I/O (TT_h); alternate function FMC_A11, additional function OPAMP2_VINM."+      },+      {+        "number": "76",+        "name": "PE7",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with analog option (TT_ha); alternate functions include TIM1_ETR, DFSDM1_DATIN2, UART7_RX, QUADSPI_BK2_IO0 and FMC_D4/FMC_DA4; additional functions OPAMP2_VOUT and COMP2_INM."+      },+      {+        "number": "77",+        "name": "PE8",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with analog option (TT_ha); alternate functions include TIM1_CH1N, DFSDM1_CKIN2, UART7_TX, QUADSPI_BK2_IO1 and FMC_D5/FMC_DA5; additional functions COMP2_OUT and OPAMP2_VINM."+      },+      {+        "number": "78",+        "name": "PE9",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with analog option (TT_ha); alternate functions include TIM1_CH1, DFSDM1_CKOUT, UART7_RTS, QUADSPI_BK2_IO2 and FMC_D6/FMC_DA6; additional functions OPAMP2_VINP and COMP2_INP."+      },+      {+        "number": "79",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "80",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "81",+        "name": "PE10",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM1_CH2N, DFSDM1_DATIN4, UART7_CTS, QUADSPI_BK2_IO3 and FMC_D7/FMC_DA7; additional function COMP2_INM."+      },+      {+        "number": "82",+        "name": "PE11",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include TIM1_CH2, DFSDM1_CKIN4, SPI4_NSS, SAI2_SD_B, FMC_D8/FMC_DA8 and LCD_G3; additional function COMP2_INP."+      },+      {+        "number": "83",+        "name": "PE12",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_CH3N, DFSDM1_DATIN5, SPI4_SCK, SAI2_SCK_B, FMC_D9/FMC_DA9, COMP1_OUT and LCD_B4."+      },+      {+        "number": "84",+        "name": "PE13",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_CH3, DFSDM1_CKIN5, SPI4_MISO, SAI2_FS_B, FMC_D10/FMC_DA10, COMP2_OUT and LCD_DE."+      },+      {+        "number": "85",+        "name": "PE14",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_CH4, SPI4_MOSI, SAI2_MCLK_B, FMC_D11/FMC_DA11 and LCD_CLK."+      },+      {+        "number": "86",+        "name": "PE15",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_BKIN, FMC_D12/FMC_DA12, TIM1_BKIN_COMP12 and LCD_R7."+      },+      {+        "number": "87",+        "name": "PB10",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include TIM2_CH3, HRTIM_SCOUT, LPTIM2_IN1, I2C2_SCL, SPI2_SCK/I2S2_CK, USART3_TX, QUADSPI_BK1_NCS, OTG_HS_ULPI_D3 and ETH_MII_RX_ER."+      },+      {+        "number": "88",+        "name": "PB11",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include TIM2_CH4, HRTIM_SCIN, LPTIM2_ETR, I2C2_SDA, USART3_RX, OTG_HS_ULPI_D4, ETH_MII_TX_EN and DSI_TE."+      },+      {+        "number": "89",+        "name": "VCAP",+        "type": "power_out",+        "description": "Connection for the external capacitor CEXT of the main regulator output; two VCAP pins can be used with an external capacitor."+      },+      {+        "number": "90",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "91",+        "name": "VDDLDO",+        "type": "power_in",+        "description": "Supply input of the embedded LDO regulator that powers the digital circuitry; decouple with 100 nF plus 1 µF."+      },+      {+        "number": "92",+        "name": "PH6",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT); alternate functions include I2C2_SMBA, SPI5_SCK, ETH_MII_RXD2, FMC_SDNE1 and DCMI_D8."+      },+      {+        "number": "93",+        "name": "PH7",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with I2C FM+ and analog options (FT_fa); alternate functions include I2C3_SCL, SPI5_MISO, ETH_MII_RXD3, FMC_SDCKE1 and DCMI_D9."+      },+      {+        "number": "94",+        "name": "PH8",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ and analog options (FT_fha); alternate functions include TIM5_ETR, I2C3_SDA, FMC_D16, DCMI_HSYNC and LCD_R2."+      },+      {+        "number": "95",+        "name": "PH9",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM12_CH2, I2C3_SMBA, FMC_D17, DCMI_D0 and LCD_R3."+      },+      {+        "number": "96",+        "name": "PH10",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM5_CH1, I2C4_SMBA, FMC_D18, DCMI_D1 and LCD_R4."+      },+      {+        "number": "97",+        "name": "PH11",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include TIM5_CH2, I2C4_SCL, FMC_D19, DCMI_D2 and LCD_R5."+      },+      {+        "number": "98",+        "name": "PH12",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include TIM5_CH3, I2C4_SDA, FMC_D20, DCMI_D3 and LCD_R6."+      },+      {+        "number": "99",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "100",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "101",+        "name": "PB12",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include TIM1_BKIN, I2C2_SMBA, SPI2_NSS/I2S2_WS, USART3_CK, FDCAN2_RX, OTG_HS_ULPI_D5, OTG_HS_ID and UART5_RX."+      },+      {+        "number": "102",+        "name": "PB13",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include TIM1_CH1N, LPTIM2_OUT, SPI2_SCK/I2S2_CK, USART3_CTS, FDCAN2_TX, OTG_HS_ULPI_D6 and UART5_TX; additional function OTG_HS_VBUS."+      },+      {+        "number": "103",+        "name": "PB14",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include TIM1_CH2N, TIM12_CH1, USART1_TX, SPI2_MISO/I2S2_SDI, USART3_RTS, UART4_RTS, SDMMC2_D0 and OTG_HS_DM."+      },+      {+        "number": "104",+        "name": "PB15",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with USB option supplied by VDD33USB (TT_u); alternate functions include RTC_REFIN, TIM1_CH3N, TIM12_CH2, USART1_RX, SPI2_MOSI/I2S2_SDO, UART4_CTS, SDMMC2_D1 and OTG_HS_DP."+      },+      {+        "number": "105",+        "name": "PD8",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_CKIN3, SAI3_SCK_B, USART3_TX, SPDIFRX1_IN2 and FMC_D13/FMC_DA13."+      },+      {+        "number": "106",+        "name": "PD9",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_DATIN3, SAI3_SD_B, USART3_RX, FDCAN2_RXFD_MODE and FMC_D14/FMC_DA14."+      },+      {+        "number": "107",+        "name": "PD10",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_CKOUT, SAI3_FS_B, USART3_CK, FDCAN2_TXFD_MODE, FMC_D15/FMC_DA15 and LCD_B3."+      },+      {+        "number": "108",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "109",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "110",+        "name": "PD11",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM2_IN2, I2C4_SMBA, USART3_CTS, QUADSPI_BK1_IO0, SAI2_SD_A and FMC_A16."+      },+      {+        "number": "111",+        "name": "PD12",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include LPTIM1_IN1, TIM4_CH1, LPTIM2_IN1, I2C4_SCL, USART3_RTS, QUADSPI_BK1_IO1 and FMC_A17."+      },+      {+        "number": "112",+        "name": "PD13",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include LPTIM1_OUT, TIM4_CH2, I2C4_SDA, QUADSPI_BK1_IO3 and FMC_A18."+      },+      {+        "number": "113",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "114",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "115",+        "name": "PD14",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM4_CH3, SAI3_MCLK_B, UART8_CTS and FMC_D0/FMC_DA0."+      },+      {+        "number": "116",+        "name": "PD15",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM4_CH4, SAI3_MCLK_A, UART8_RTS/UART8_DE and FMC_D1/FMC_DA1."+      },+      {+        "number": "117",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "118",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "119",+        "name": "VCAPDSI",+        "type": "power_out",+        "description": "DSI regulator capacitor pin; must be externally connected to the VDD12DSI pin."+      },+      {+        "number": "120",+        "name": "VDD12DSI",+        "type": "power_in",+        "description": "1.2 V supply pin of the DSI PHY (DSI regulator domain); must be externally connected to VCAPDSI."+      },+      {+        "number": "121",+        "name": "DSI_D0P",+        "type": "bidirectional",+        "description": "MIPI DSI PHY data lane 0 positive differential pin (3.3 V-tolerant, TT)."+      },+      {+        "number": "122",+        "name": "DSI_D0N",+        "type": "bidirectional",+        "description": "MIPI DSI PHY data lane 0 negative differential pin (3.3 V-tolerant, TT)."+      },+      {+        "number": "123",+        "name": "VSSDSI",+        "type": "power_in",+        "description": "Ground pin of the DSI PHY."+      },+      {+        "number": "124",+        "name": "DSI_CKP",+        "type": "bidirectional",+        "description": "MIPI DSI PHY clock lane positive differential pin (3.3 V-tolerant, TT)."+      },+      {+        "number": "125",+        "name": "DSI_CKN",+        "type": "bidirectional",+        "description": "MIPI DSI PHY clock lane negative differential pin (3.3 V-tolerant, TT)."+      },+      {+        "number": "126",+        "name": "VDD12DSI",+        "type": "power_in",+        "description": "1.2 V supply pin of the DSI PHY (DSI regulator domain); must be externally connected to VCAPDSI."+      },+      {+        "number": "127",+        "name": "DSI_D1P",+        "type": "bidirectional",+        "description": "MIPI DSI PHY data lane 1 positive differential pin (3.3 V-tolerant, TT)."+      },+      {+        "number": "128",+        "name": "DSI_D1N",+        "type": "bidirectional",+        "description": "MIPI DSI PHY data lane 1 negative differential pin (3.3 V-tolerant, TT)."+      },+      {+        "number": "129",+        "name": "VSSDSI",+        "type": "power_in",+        "description": "Ground pin of the DSI PHY."+      },+      {+        "number": "130",+        "name": "PG2",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_BKIN, TIM8_BKIN_COMP12 and FMC_A12."+      },+      {+        "number": "131",+        "name": "PG3",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_BKIN2, TIM8_BKIN2_COMP12 and FMC_A13."+      },+      {+        "number": "132",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "133",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "134",+        "name": "PG4",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_BKIN2, TIM1_BKIN2_COMP12 and FMC_A14/FMC_BA0."+      },+      {+        "number": "135",+        "name": "PG5",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM1_ETR and FMC_A15/FMC_BA1."+      },+      {+        "number": "136",+        "name": "PG6",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM17_BKIN, HRTIM_CHE1, QUADSPI_BK1_NCS, FMC_NE3, DCMI_D12 and LCD_R7."+      },+      {+        "number": "137",+        "name": "PG7",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_CHE2, SAI1_MCLK_A, USART6_CK, FMC_INT, DCMI_D13 and LCD_CLK."+      },+      {+        "number": "138",+        "name": "PG8",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_ETR, SPI6_NSS, USART6_RTS, SPDIFRX1_IN3, ETH_PPS_OUT, FMC_SDCLK and LCD_G7."+      },+      {+        "number": "139",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "140",+        "name": "VDD50USB",+        "type": "power_in",+        "description": "USB power input for the dedicated USB regulator that generates the 3.3 V supply for the internal USB PHYs."+      },+      {+        "number": "141",+        "name": "VDD33USB",+        "type": "power_in",+        "description": "3.3 V USB supply pin for the USB PHYs and USB I/O option; specified for 3.0 to 3.6 V."+      },+      {+        "number": "142",+        "name": "PC6",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_CHA1, TIM3_CH1, TIM8_CH1, DFSDM1_CKIN3, I2S2_MCK, USART6_TX, FMC_NWAIT and DCMI_D0."+      },+      {+        "number": "143",+        "name": "PC7",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TRGIO, HRTIM_CHA2, TIM3_CH2, TIM8_CH2, I2S3_MCK, USART6_RX, FMC_NE1 and DCMI_D1."+      },+      {+        "number": "144",+        "name": "PC8",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED1, HRTIM_CHB1, TIM3_CH3, TIM8_CH3, USART6_CK, UART5_RTS, FMC_NE2/FMC_NCE and DCMI_D2."+      },+      {+        "number": "145",+        "name": "PC9",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include MCO2, TIM3_CH4, TIM8_CH4, I2C3_SDA, I2S_CKIN, UART5_CTS, QUADSPI_BK1_IO0 and LCD_G3."+      },+      {+        "number": "146",+        "name": "PA8",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ and analog options (FT_fha); alternate functions include MCO1, TIM1_CH1, HRTIM_CHB2, I2C3_SCL, USART1_CK, OTG_FS_SOF, UART7_RX, LCD_B3 and LCD_R6."+      },+      {+        "number": "147",+        "name": "PA9",+        "type": "bidirectional",+        "description": "3.3 V-tolerant I/O with USB option supplied by VDD33USB (FT_u); alternate functions include TIM1_CH2, HRTIM_CHC1, LPUART1_TX, I2C3_SMBA, SPI2_SCK/I2S2_CK, USART1_TX, FDCAN1_RXFD_MODE, DCMI_D0 and LCD_R5; additional function OTG_FS_VBUS."+      },+      {+        "number": "148",+        "name": "PA10",+        "type": "bidirectional",+        "description": "USB-option I/O supplied by VDD33USB (FT_u); alternate functions include TIM1_CH3, HRTIM_CHC2, LPUART1_RX, USART1_RX, FDCAN1_TXFD_MODE, OTG_FS_ID, MDIOS_MDIO, DCMI_D1 and LCD_B1."+      },+      {+        "number": "149",+        "name": "PA11",+        "type": "bidirectional",+        "description": "USB-option I/O supplied by VDD33USB (FT_u); alternate functions include TIM1_CH4, HRTIM_CHD1, LPUART1_CTS, SPI2_NSS/I2S2_WS, UART4_RX, USART1_CTS, FDCAN1_RX, OTG_FS_DM and LCD_R4."+      },+      {+        "number": "150",+        "name": "PA12",+        "type": "bidirectional",+        "description": "USB-option I/O supplied by VDD33USB (FT_u); alternate functions include TIM1_ETR, HRTIM_CHD2, LPUART1_RTS, SPI2_SCK/I2S2_CK, UART4_TX, USART1_RTS, SAI2_FS_B, FDCAN1_TX, OTG_FS_DP and LCD_R5."+      },+      {+        "number": "151",+        "name": "PA13",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT) multiplexed with the JTMS/SWDIO debug function; alternate function EVENTOUT."+      },+      {+        "number": "152",+        "name": "VCAP",+        "type": "power_out",+        "description": "Connection for the external capacitor CEXT of the main regulator output; two VCAP pins can be used with an external capacitor."+      },+      {+        "number": "153",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "154",+        "name": "VDDLDO",+        "type": "power_in",+        "description": "Supply input of the embedded LDO regulator that powers the digital circuitry; decouple with 100 nF plus 1 µF."+      },+      {+        "number": "155",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "156",+        "name": "PH13",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH1N, UART4_TX, FDCAN1_TX, FMC_D21 and LCD_G2."+      },+      {+        "number": "157",+        "name": "PH14",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH2N, UART4_RX, FDCAN1_RX, FMC_D22, DCMI_D4 and LCD_G3."+      },+      {+        "number": "158",+        "name": "PH15",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH3N, FDCAN1_TXFD_MODE, FMC_D23, DCMI_D11 and LCD_G4."+      },+      {+        "number": "159",+        "name": "PI0",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM5_CH4, SPI2_NSS/I2S2_WS, FDCAN1_RXFD_MODE, FMC_D24, DCMI_D13 and LCD_G5."+      },+      {+        "number": "160",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "161",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "162",+        "name": "PI1",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_BKIN2, SPI2_SCK/I2S2_CK, TIM8_BKIN2_COMP12, FMC_D25, DCMI_D8 and LCD_G6."+      },+      {+        "number": "163",+        "name": "PI2",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH4, SPI2_MISO/I2S2_SDI, FMC_D26, DCMI_D9 and LCD_G7."+      },+      {+        "number": "164",+        "name": "PI3",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_ETR, SPI2_MOSI/I2S2_SDO, FMC_D27 and DCMI_D10."+      },+      {+        "number": "165",+        "name": "PA14",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT) multiplexed with the JTCK/SWCLK debug function; alternate function EVENTOUT."+      },+      {+        "number": "166",+        "name": "PA15",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT) multiplexed with the JTDI debug function; alternate functions include TIM2_CH1/TIM2_ETR, HRTIM_FLT1, CEC, SPI1_NSS/I2S1_WS, SPI3_NSS/I2S3_WS, SPI6_NSS, UART4_RTS, UART7_TX and DSI_TE."+      },+      {+        "number": "167",+        "name": "PC10",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with analog option (FT_ha); alternate functions include HRTIM_EEV1, DFSDM1_CKIN5, SPI3_SCK/I2S3_CK, USART3_TX, UART4_TX, QUADSPI_BK1_IO1, SDMMC1_D2, DCMI_D8 and LCD_R2."+      },+      {+        "number": "168",+        "name": "PC11",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_FLT2, DFSDM1_DATIN5, SPI3_MISO/I2S3_SDI, USART3_RX, UART4_RX, QUADSPI_BK2_NCS, SDMMC1_D3 and DCMI_D4."+      },+      {+        "number": "169",+        "name": "PC12",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED3, HRTIM_EEV2, SPI3_MOSI/I2S3_SDO, USART3_CK, UART5_TX, SDMMC1_CK and DCMI_D9."+      },+      {+        "number": "170",+        "name": "PD0",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_CKIN6, SAI3_SCK_A, UART4_RX, FDCAN1_RX and FMC_D2/FMC_DA2."+      },+      {+        "number": "171",+        "name": "PD1",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_DATIN6, SAI3_SD_A, UART4_TX, FDCAN1_TX and FMC_D3/FMC_DA3."+      },+      {+        "number": "172",+        "name": "PD2",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED2, TIM3_ETR, UART5_RX, SDMMC1_CMD and DCMI_D11."+      },+      {+        "number": "173",+        "name": "PD3",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_CKOUT, SPI2_SCK/I2S2_CK, USART2_CTS, FMC_CLK, DCMI_D5 and LCD_G7."+      },+      {+        "number": "174",+        "name": "PD4",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_FLT3, SAI3_FS_A, USART2_RTS, FDCAN1_RXFD_MODE and FMC_NOE."+      },+      {+        "number": "175",+        "name": "PD5",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_EEV3, USART2_TX, FDCAN1_TXFD_MODE and FMC_NWE."+      },+      {+        "number": "176",+        "name": "PD6",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include SAI1_D1, DFSDM1_CKIN4, DFSDM1_DATIN1, SPI3_MOSI/I2S3_SDO, USART2_RX, FDCAN2_RXFD_MODE, SDMMC2_CK, FMC_NWAIT, DCMI_D10 and LCD_B2."+      },+      {+        "number": "177",+        "name": "PD7",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include DFSDM1_DATIN4, SPI1_MOSI/I2S1_SDO, DFSDM1_CKIN1, USART2_CK, SPDIFRX1_IN0, SDMMC2_CMD and FMC_NE1."+      },+      {+        "number": "178",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "179",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "180",+        "name": "PG9",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include SPI1_MISO/I2S1_SDI, USART6_RX, SPDIFRX1_IN4, QUADSPI_BK2_IO2, SAI2_FS_B, FMC_NE2/FMC_NCE and DCMI_VSYNC."+      },+      {+        "number": "181",+        "name": "PG10",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include HRTIM_FLT5, SPI1_NSS/I2S1_WS, LCD_G3, SAI2_SD_B, FMC_NE3, DCMI_D2 and LCD_B2."+      },+      {+        "number": "182",+        "name": "PG11",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM1_IN2, HRTIM_EEV4, SPI1_SCK/I2S1_CK, SPDIFRX1_IN1, SDMMC2_D2, ETH_MII_TX_EN, DCMI_D3 and LCD_B3."+      },+      {+        "number": "183",+        "name": "PG12",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM1_IN1, HRTIM_EEV5, SPI6_MISO, USART6_RTS, SPDIFRX1_IN2, LCD_B4, ETH_MII_TXD1, FMC_NE4 and LCD_B1."+      },+      {+        "number": "184",+        "name": "PG13",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED0, LPTIM1_OUT, HRTIM_EEV10, SPI6_SCK, USART6_CTS, ETH_MII_TXD0, FMC_A24 and LCD_R0."+      },+      {+        "number": "185",+        "name": "PG14",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TRACED1, LPTIM1_ETR, SPI6_MOSI, USART6_TX, QUADSPI_BK2_IO3, ETH_MII_TXD1, FMC_A25 and LCD_B0."+      },+      {+        "number": "186",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "187",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      },+      {+        "number": "188",+        "name": "PG15",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include USART6_CTS, FMC_SDNCAS and DCMI_D13."+      },+      {+        "number": "189",+        "name": "PB3",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT) multiplexed with the JTDO/TRACESWO debug function; alternate functions include TIM2_CH2, HRTIM_FLT4, SPI1_SCK/I2S1_CK, SPI3_SCK/I2S3_CK, SPI6_SCK, SDMMC2_D2, CRS_SYNC and UART7_RX."+      },+      {+        "number": "190",+        "name": "PB4",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT) multiplexed with the NJTRST debug function; alternate functions include TIM16_BKIN, TIM3_CH1, HRTIM_EEV6, SPI1_MISO/I2S1_SDI, SPI3_MISO/I2S3_SDI, SPI2_NSS/I2S2_WS, SPI6_MISO, SDMMC2_D3 and UART7_TX."+      },+      {+        "number": "191",+        "name": "PB5",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O (FT); alternate functions include TIM17_BKIN, TIM3_CH2, HRTIM_EEV7, I2C1_SMBA, SPI1_MOSI/I2S1_SDO, SPI3_MOSI/I2S3_SDO, FDCAN2_RX, OTG_HS_ULPI_D7, ETH_PPS_OUT, FMC_SDCKE1, DCMI_D10 and UART5_RX."+      },+      {+        "number": "192",+        "name": "PB6",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with I2C FM+ option (FT_f); alternate functions include TIM16_CH1N, TIM4_CH1, HRTIM_EEV8, I2C1_SCL, CEC, I2C4_SCL, USART1_TX, LPUART1_TX, FDCAN2_TX, QUADSPI_BK1_NCS, FMC_SDNE1 and DCMI_D5."+      },+      {+        "number": "193",+        "name": "PB7",+        "type": "bidirectional",+        "description": "5 V-tolerant I/O with I2C FM+ and analog options (FT_fa); alternate functions include TIM17_CH1N, TIM4_CH2, HRTIM_EEV9, I2C1_SDA, I2C4_SDA, USART1_RX, LPUART1_RX, FMC_NL and DCMI_VSYNC; additional function PVD_IN."+      },+      {+        "number": "194",+        "name": "BOOT0",+        "type": "input",+        "description": "Dedicated BOOT0 input pin; its input voltage can go up to 9.0 V (VPP function), and it is excluded from the standard VIL/VIH I/O thresholds."+      },+      {+        "number": "195",+        "name": "PB8",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include TIM16_CH1, TIM4_CH3, DFSDM1_CKIN7, I2C1_SCL, I2C4_SCL, SDMMC1_CKIN, UART4_RX, FDCAN1_RX, SDMMC2_D4, SDMMC1_D4, DCMI_D6 and LCD_B6."+      },+      {+        "number": "196",+        "name": "PB9",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O with I2C FM+ option (FT_fh); alternate functions include TIM17_CH1, TIM4_CH4, DFSDM1_DATIN7, I2C1_SDA, SPI2_NSS/I2S2_WS, I2C4_SDA, SDMMC1_CDIR, UART4_TX, FDCAN1_TX, SDMMC2_D5, DCMI_D7 and LCD_B7."+      },+      {+        "number": "197",+        "name": "PE0",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM1_ETR, TIM4_ETR, HRTIM_SCIN, LPTIM2_ETR, UART8_RX, FDCAN1_RXFD_MODE, SAI2_MCLK_A, FMC_NBL0 and DCMI_D2."+      },+      {+        "number": "198",+        "name": "PE1",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include LPTIM1_IN2, HRTIM_SCOUT, UART8_TX, FDCAN1_TXFD_MODE, FMC_NBL1 and DCMI_D3."+      },+      {+        "number": "199",+        "name": "VCAP",+        "type": "power_out",+        "description": "Connection for the external capacitor CEXT of the main regulator output; two VCAP pins can be used with an external capacitor."+      },+      {+        "number": "200",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "201",+        "name": "PDR_ON",+        "type": "input",+        "description": "5 V-tolerant input pin (FT) named PDR_ON, associated with the power-down reset circuitry; no further electrical limits are given in the pin table."+      },+      {+        "number": "202",+        "name": "VDDLDO",+        "type": "power_in",+        "description": "Supply input of the embedded LDO regulator that powers the digital circuitry; decouple with 100 nF plus 1 µF."+      },+      {+        "number": "203",+        "name": "PI4",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_BKIN, SAI2_MCLK_A, TIM8_BKIN_COMP12, FMC_NBL2, DCMI_D5 and LCD_B4."+      },+      {+        "number": "204",+        "name": "PI5",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH1, SAI2_SCK_A, FMC_NBL3, DCMI_VSYNC and LCD_B5."+      },+      {+        "number": "205",+        "name": "PI6",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH2, SAI2_SD_A, FMC_D28, DCMI_D6 and LCD_B6."+      },+      {+        "number": "206",+        "name": "PI7",+        "type": "bidirectional",+        "description": "5 V-tolerant high-speed I/O (FT_h); alternate functions include TIM8_CH3, SAI2_FS_A, FMC_D29, DCMI_D7 and LCD_B7."+      },+      {+        "number": "207",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground pin; must be connected to the board ground, with variations between ground pins not exceeding 50 mV."+      },+      {+        "number": "208",+        "name": "VDD",+        "type": "power_in",+        "description": "Main supply pin for the 1.62 to 3.6 V application supply and I/Os; variations between VDD pins of the same domain must not exceed 50 mV."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.3",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.3",+        "primary_model": "claude-haiku-5-5",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Package scope: the LQFP208 pin assignment was taken from the LQFP208 column of Table 7 (pin/ball def; Source pages are approximate: they are the PDF page markers on which each pin's row appears in Table; Type mapping: datasheet classes S (supply) were mapped to power_in, except VLXSMPS, VCAP and VCAPDSI"+        ],+        "pages_sent": 100,+        "cost_usd": 0.8811,+        "at": "2026-10-08T20:00:15"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588886236752982016",+        "pages": 252,+        "sha256": "b96e900fb695da6c",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 208,+        "described": 208,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    },+    "models_3d": [+      {+        "file": "stm32h747bit6.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          30,+          30,+          1.5+        ],+        "zmin_mm": 0,+        "centre_offset_mm": 0,+        "footprint_binding": "identity",+        "sha256": "e3717f35ab17b7b1224af915b854103d4ab8675b952348f37773a9bee5c7a38e",+        "checked": "2026-10-08",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "stm32h747bit6-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          30,+          30,+          1.5+        ],+        "zmin_mm": 0,+        "centre_offset_mm": 0,+        "footprint_binding": "identity",+        "sha256": "ce2a4a20643d11d402af4bc1aef2210795bbd4bb67381824d46ee121ed07a826",+        "checked": "2026-10-08",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file