← Commit history

Initial commit: component/spirit1qtr

Ray ·4d1a708d74 ·
2 files changed +276
README.mdadded+57
@@ -0,0 +1,57 @@+# SPIRIT1QTR++**STMicroelectronics** · RF Transceiver ICs · QFN-20-EP(4x4)++SPIRIT1QTR from STMicroelectronics, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | GPIO_0 | bidirectional | Configurable general purpose I/O programmable for MCU clock output, FIFO status flags, wake-up input, battery level detector, TX-RX external switch control, antenna diversity control, or temperature sensor output; 0-VDD V operating range. |+| 2 | MISO | output | SPI data output pin for serial peripheral interface slave read operations; 0-3.9 V operating range. |+| 3 | MOSI | input | SPI data input pin for serial peripheral interface slave write operations; 0-3.9 V operating range. |+| 4 | SCLK | input | SPI clock input pin from master; 0-3.9 V operating range. |+| 5 | CSn | input | SPI chip select input pin, active low for slave selection; 0-3.9 V operating range. |+| 6 | XOUT | output | Crystal oscillator output connected to external 26 MHz crystal or left floating when using external clock on XIN; 0-1.4 V operating range. |+| 7 | XIN | input | Crystal oscillator input connected to external 26 MHz crystal or external clock source with DC coupling at 0.2 VDC nominal and minimum 400 mVpp AC amplitude; 0-1.4 V instantaneous maximum. |+| 8 | VBAT | power_in | Power supply input voltage with +1.8 V to +3.6 V operating range. |+| 9 | RXp | input | Differential RF input signal positive terminal for low-noise amplifier; 0-1.4 V operating range. |+| 10 | RXn | input | Differential RF input signal negative terminal for low-noise amplifier; 0-1.4 V operating range. |+| 11 | GND_PA | power_in | Ground pin for power amplifier that must be carefully decoupled from other ground pins; -0.3 to 3.9 V absolute maximum. |+| 12 | TX | output | RF output signal from transmitter to antenna via external matching network; 0-3.9 V operating range. |+| 13 | SMPS Ext2 | power_in | Regulated DC-DC voltage input to external switching mode power supply; 0-1.8 V operating range. |+| 14 | SMPS Ext1 | power_out | DC-DC output pin from internal switching mode power supply connected to external LC filter; 0-3.9 V operating range. |+| 15 | SDN | input | Shutdown input pin that must be 0 in all modes except shutdown; when SDN=1 the SPIRIT1 is shut down and register contents are lost, GPIO and SPI in HiZ; 0-VDD V operating range. |+| 16 | VBAT | power_in | Power supply input voltage with +1.8 V to +3.6 V operating range. |+| 17 | VREG | power_out | Regulated output voltage of 1.8 V for SPIRIT1 internal use only, requires 100 nF decoupling capacitor and cannot supply other devices; -0.3 to 1.4 V absolute maximum. |+| 18 | GPIO3 | bidirectional | Configurable general purpose I/O programmable for MCU clock output, FIFO status flags, wake-up input, battery level detector, TX-RX external switch control, antenna diversity control, or temperature sensor output; 0-VDD V operating range. |+| 19 | GPIO2 | bidirectional | Configurable general purpose I/O programmable for MCU clock output, FIFO status flags, wake-up input, battery level detector, TX-RX external switch control, antenna diversity control, or temperature sensor output; 0-VDD V operating range. |+| 20 | GPIO1 | bidirectional | Configurable general purpose I/O programmable for MCU clock output, FIFO status flags, wake-up input, battery level detector, TX-RX external switch control, antenna diversity control, or temperature sensor output; 0-VDD V operating range. |+| 21 | GND | power_in | Ground connection and exposed pad for heat dissipation and ground reference; -0.3 to 3.9 V absolute maximum. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | QFN-20-EP(4x4) |+| Category | RF And Wireless |+| Pins | 21 |++## CAD (KiCad official)++- Symbol: `SPIRIT1QTR`+- Footprint: `Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm`+- 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `spirit1qtr-etched.step` / `spirit1qtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `spirit1qtr.step` / `spirit1qtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588941848257290240) (104 pp, sha256 `2ed30e6860d67a45`, retrieved 2026-09-23, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/spirit1qtr-datasheet.pdf)
page.jsonadded+219
@@ -0,0 +1,219 @@+{+  "slug": "spirit1qtr",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics RF Transceiver ICs, QFN-20-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "rf and wireless",+    "spirit1qtr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "spirit1qtr.kicad_sym",+    "spirit1qtr.kicad_mod",+    "spirit1qtr.glb",+    "spirit1qtr.step",+    "spirit1qtr.lbr",+    "docs/hero.png",+    "docs/spirit1qtr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "SPIRIT1QTR",+    "manufacturer": "STMicroelectronics",+    "package": "QFN-20-EP(4x4)",+    "pin_count": 21,+    "category": "RF And Wireless",+    "subcategory": "RF Transceiver ICs",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588941848257290240",+    "parts": {+      "symbol": "spirit1qtr.kicad_sym",+      "footprint": "spirit1qtr.kicad_mod",+      "model_3d": "spirit1qtr-etched.glb",+      "model_3d_plain": "spirit1qtr.glb",+      "model_3d_step": "spirit1qtr-etched.step",+      "model_3d_step_plain": "spirit1qtr.step",+      "lbr": "spirit1qtr.lbr"+    },+    "distributor_links": {+      "lcsc": "C2654653"+    },+    "pins": [+      {+        "number": "1",+        "name": "GPIO_0",+        "type": "bidirectional",+        "description": "Configurable general purpose I/O programmable for MCU clock output, FIFO status flags, wake-up input, battery level detector, TX-RX external switch control, antenna diversity control, or temperature sensor output; 0-VDD V operating range."+      },+      {+        "number": "2",+        "name": "MISO",+        "type": "output",+        "description": "SPI data output pin for serial peripheral interface slave read operations; 0-3.9 V operating range."+      },+      {+        "number": "3",+        "name": "MOSI",+        "type": "input",+        "description": "SPI data input pin for serial peripheral interface slave write operations; 0-3.9 V operating range."+      },+      {+        "number": "4",+        "name": "SCLK",+        "type": "input",+        "description": "SPI clock input pin from master; 0-3.9 V operating range."+      },+      {+        "number": "5",+        "name": "CSn",+        "type": "input",+        "description": "SPI chip select input pin, active low for slave selection; 0-3.9 V operating range."+      },+      {+        "number": "6",+        "name": "XOUT",+        "type": "output",+        "description": "Crystal oscillator output connected to external 26 MHz crystal or left floating when using external clock on XIN; 0-1.4 V operating range."+      },+      {+        "number": "7",+        "name": "XIN",+        "type": "input",+        "description": "Crystal oscillator input connected to external 26 MHz crystal or external clock source with DC coupling at 0.2 VDC nominal and minimum 400 mVpp AC amplitude; 0-1.4 V instantaneous maximum."+      },+      {+        "number": "8",+        "name": "VBAT",+        "type": "power_in",+        "description": "Power supply input voltage with +1.8 V to +3.6 V operating range."+      },+      {+        "number": "9",+        "name": "RXp",+        "type": "input",+        "description": "Differential RF input signal positive terminal for low-noise amplifier; 0-1.4 V operating range."+      },+      {+        "number": "10",+        "name": "RXn",+        "type": "input",+        "description": "Differential RF input signal negative terminal for low-noise amplifier; 0-1.4 V operating range."+      },+      {+        "number": "11",+        "name": "GND_PA",+        "type": "power_in",+        "description": "Ground pin for power amplifier that must be carefully decoupled from other ground pins; -0.3 to 3.9 V absolute maximum."+      },+      {+        "number": "12",+        "name": "TX",+        "type": "output",+        "description": "RF output signal from transmitter to antenna via external matching network; 0-3.9 V operating range."+      },+      {+        "number": "13",+        "name": "SMPS Ext2",+        "type": "power_in",+        "description": "Regulated DC-DC voltage input to external switching mode power supply; 0-1.8 V operating range."+      },+      {+        "number": "14",+        "name": "SMPS Ext1",+        "type": "power_out",+        "description": "DC-DC output pin from internal switching mode power supply connected to external LC filter; 0-3.9 V operating range."+      },+      {+        "number": "15",+        "name": "SDN",+        "type": "input",+        "description": "Shutdown input pin that must be 0 in all modes except shutdown; when SDN=1 the SPIRIT1 is shut down and register contents are lost, GPIO and SPI in HiZ; 0-VDD V operating range."+      },+      {+        "number": "16",+        "name": "VBAT",+        "type": "power_in",+        "description": "Power supply input voltage with +1.8 V to +3.6 V operating range."+      },+      {+        "number": "17",+        "name": "VREG",+        "type": "power_out",+        "description": "Regulated output voltage of 1.8 V for SPIRIT1 internal use only, requires 100 nF decoupling capacitor and cannot supply other devices; -0.3 to 1.4 V absolute maximum."+      },+      {+        "number": "18",+        "name": "GPIO3",+        "type": "bidirectional",+        "description": "Configurable general purpose I/O programmable for MCU clock output, FIFO status flags, wake-up input, battery level detector, TX-RX external switch control, antenna diversity control, or temperature sensor output; 0-VDD V operating range."+      },+      {+        "number": "19",+        "name": "GPIO2",+        "type": "bidirectional",+        "description": "Configurable general purpose I/O programmable for MCU clock output, FIFO status flags, wake-up input, battery level detector, TX-RX external switch control, antenna diversity control, or temperature sensor output; 0-VDD V operating range."+      },+      {+        "number": "20",+        "name": "GPIO1",+        "type": "bidirectional",+        "description": "Configurable general purpose I/O programmable for MCU clock output, FIFO status flags, wake-up input, battery level detector, TX-RX external switch control, antenna diversity control, or temperature sensor output; 0-VDD V operating range."+      },+      {+        "number": "21",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection and exposed pad for heat dissipation and ground reference; -0.3 to 3.9 V absolute maximum."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 104,+        "cost_usd": 0.883,+        "at": "2026-09-23T13:19:09"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588941848257290240",+        "pages": 104,+        "sha256": "2ed30e6860d67a45",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 21,+        "described": 21,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file