component
SN74LV541ATPWR
Public Made by Adomby adom
Texas Instruments Buffers, Drivers, Receivers, Transceivers, TSSOP-20. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+56@@ -0,0 +1,56 @@+# SN74LV541ATPWR++**Texas Instruments** · Buffers, Drivers, Receivers, Transceivers · TSSOP-20++SN74LV541ATPWR from Texas Instruments, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OE1 | input | Active-low output enable for the first buffer group; if OE1 or OE2 is high, all corresponding outputs are placed in the high-impedance state, and OE should be tied to VCC through a pullup resistor to keep outputs high-impedance during power up or power down. |+| 2 | A1 | input | Data input to buffer channel 1, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND. |+| 3 | A2 | input | Data input to buffer channel 2, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND. |+| 4 | A3 | input | Data input to buffer channel 3, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND. |+| 5 | A4 | input | Data input to buffer channel 4, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND. |+| 6 | A5 | input | Data input to buffer channel 5, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND. |+| 7 | A6 | input | Data input to buffer channel 6, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND. |+| 8 | A7 | input | Data input to buffer channel 7, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND. |+| 9 | A8 | input | Data input to buffer channel 8, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND. |+| 10 | GND | power_in | Ground reference pin for the device. |+| 11 | Y8 | tri_state | Noninverting 3-state output of channel 8 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high. |+| 12 | Y7 | tri_state | Noninverting 3-state output of channel 7 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high. |+| 13 | Y6 | tri_state | Noninverting 3-state output of channel 6 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high. |+| 14 | Y5 | tri_state | Noninverting 3-state output of channel 5 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high. |+| 15 | Y4 | tri_state | Noninverting 3-state output of channel 4 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high. |+| 16 | Y3 | tri_state | Noninverting 3-state output of channel 3 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high. |+| 17 | Y2 | tri_state | Noninverting 3-state output of channel 2 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high. |+| 18 | Y1 | tri_state | Noninverting 3-state output of channel 1 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high. |+| 19 | OE2 | input | Active-low output enable for the second buffer group; if OE1 or OE2 is high, all corresponding outputs are placed in the high-impedance state, and OE should be tied to VCC through a pullup resistor to keep outputs high-impedance during power up or power down. |+| 20 | VCC | power_in | Positive supply, specified for 4.5 V to 5.5 V operation with absolute maximum of 7 V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-20 |+| Category | Logic |+| Pins | 20 |++## CAD (KiCad official)++- Symbol: `SN74LV541ATPWR`+- Footprint: `Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm`+- 3D model: TSSOP-20 (KiCad packages3D, STEP)+- 3D model files: `sn74lv541atpwr-etched.step` / `sn74lv541atpwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `sn74lv541atpwr.step` / `sn74lv541atpwr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/sn74lv541at.pdf) (22 pp, sha256 `edf51e98d825a642`, retrieved 2026-10-08, tier: manufacturer)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/sn74lv541atpwr-datasheet.pdf)
page.jsonadded+271@@ -0,0 +1,271 @@+{+ "slug": "sn74lv541atpwr",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments Buffers, Drivers, Receivers, Transceivers, TSSOP-20. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "logic",+ "sn74lv541atpwr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "sn74lv541atpwr.kicad_sym",+ "sn74lv541atpwr.kicad_mod",+ "sn74lv541atpwr.glb",+ "sn74lv541atpwr.step",+ "sn74lv541atpwr.lbr",+ "docs/hero.png",+ "docs/sn74lv541atpwr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "sn74lv541atpwr-hero.glb",+ "sn74lv541atpwr-hero.overlay.json"+ ],+ "component": {+ "mpn": "SN74LV541ATPWR",+ "manufacturer": "Texas Instruments",+ "package": "TSSOP-20",+ "pin_count": 20,+ "category": "Logic",+ "subcategory": "Buffers, Drivers, Receivers, Transceivers",+ "datasheet": "https://www.ti.com/lit/ds/symlink/sn74lv541at.pdf",+ "parts": {+ "symbol": "sn74lv541atpwr.kicad_sym",+ "footprint": "sn74lv541atpwr.kicad_mod",+ "model_3d": "sn74lv541atpwr-hero.glb",+ "model_3d_plain": "sn74lv541atpwr.glb",+ "model_3d_step": "sn74lv541atpwr-etched.step",+ "model_3d_step_plain": "sn74lv541atpwr.step",+ "lbr": "sn74lv541atpwr.lbr"+ },+ "distributor_links": {+ "lcsc": "C544577",+ "digikey": "296-18698-2-ND",+ "mouser": "595-SN74LV541ATPWR"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T18:26:40Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "296-18698-2-ND",+ "status": "found"+ },+ "mouser": {+ "pn": "595-SN74LV541ATPWR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "OE1",+ "type": "input",+ "description": "Active-low output enable for the first buffer group; if OE1 or OE2 is high, all corresponding outputs are placed in the high-impedance state, and OE should be tied to VCC through a pullup resistor to keep outputs high-impedance during power up or power down."+ },+ {+ "number": "2",+ "name": "A1",+ "type": "input",+ "description": "Data input to buffer channel 1, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND."+ },+ {+ "number": "3",+ "name": "A2",+ "type": "input",+ "description": "Data input to buffer channel 2, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND."+ },+ {+ "number": "4",+ "name": "A3",+ "type": "input",+ "description": "Data input to buffer channel 3, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND."+ },+ {+ "number": "5",+ "name": "A4",+ "type": "input",+ "description": "Data input to buffer channel 4, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND."+ },+ {+ "number": "6",+ "name": "A5",+ "type": "input",+ "description": "Data input to buffer channel 5, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND."+ },+ {+ "number": "7",+ "name": "A6",+ "type": "input",+ "description": "Data input to buffer channel 6, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND."+ },+ {+ "number": "8",+ "name": "A7",+ "type": "input",+ "description": "Data input to buffer channel 7, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND."+ },+ {+ "number": "9",+ "name": "A8",+ "type": "input",+ "description": "Data input to buffer channel 8, TTL-voltage compatible with VCC of 4.5 V to 5.5 V; unused inputs must be held at VCC or GND."+ },+ {+ "number": "10",+ "name": "GND",+ "type": "power_in",+ "description": "Ground reference pin for the device."+ },+ {+ "number": "11",+ "name": "Y8",+ "type": "tri_state",+ "description": "Noninverting 3-state output of channel 8 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high."+ },+ {+ "number": "12",+ "name": "Y7",+ "type": "tri_state",+ "description": "Noninverting 3-state output of channel 7 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high."+ },+ {+ "number": "13",+ "name": "Y6",+ "type": "tri_state",+ "description": "Noninverting 3-state output of channel 6 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high."+ },+ {+ "number": "14",+ "name": "Y5",+ "type": "tri_state",+ "description": "Noninverting 3-state output of channel 5 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high."+ },+ {+ "number": "15",+ "name": "Y4",+ "type": "tri_state",+ "description": "Noninverting 3-state output of channel 4 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high."+ },+ {+ "number": "16",+ "name": "Y3",+ "type": "tri_state",+ "description": "Noninverting 3-state output of channel 3 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high."+ },+ {+ "number": "17",+ "name": "Y2",+ "type": "tri_state",+ "description": "Noninverting 3-state output of channel 2 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high."+ },+ {+ "number": "18",+ "name": "Y1",+ "type": "tri_state",+ "description": "Noninverting 3-state output of channel 1 that provides noninverted data when enabled and is high-impedance when OE1 or OE2 is high."+ },+ {+ "number": "19",+ "name": "OE2",+ "type": "input",+ "description": "Active-low output enable for the second buffer group; if OE1 or OE2 is high, all corresponding outputs are placed in the high-impedance state, and OE should be tied to VCC through a pullup resistor to keep outputs high-impedance during power up or power down."+ },+ {+ "number": "20",+ "name": "VCC",+ "type": "power_in",+ "description": "Positive supply, specified for 4.5 V to 5.5 V operation with absolute maximum of 7 V."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The PW (TSSOP-20) pin map is not printed as a clean numbered list in the extracted text; the names a; Pin types for the Y outputs are given as tri_state (3-state outputs per the datasheet). The datashee"+ ],+ "pages_sent": 22,+ "cost_usd": 0.0873,+ "at": "2026-10-08T18:26:18"+ },+ "datasheet": {+ "url": "https://www.ti.com/lit/ds/symlink/sn74lv541at.pdf",+ "pages": 22,+ "sha256": "edf51e98d825a642",+ "source_tier": "mfr"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 20,+ "described": 20,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "sn74lv541atpwr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 6.5,+ 1.2+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "97339947f3a7196470ec2f1d9f9b92bb2fc2ab66ad53be0cf105192585ef3c9a",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "sn74lv541atpwr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 6.5,+ 1.2+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "c903341e987f6d1b920a1889942e55adf394f16040fa0a0902139efa842f9a20",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}