← Commit history
README.mdadded+60@@ -0,0 +1,60 @@+# SG3525A++**IDCHIP** · AC-DC Controllers and Regulators · SOP-16++SG3525A from IDCHIP, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | Inv. Input | input | Inverting input of the on-chip error amplifier. Common-mode range 1.5 V to 5.2 V (covers the internal Vref = 5.1 V so no external resistor divider is required for reference-based feedback). Input offset 2 mV typ, input bias 1 µA typ. |+| 2 | Noninv. Input | input | Non-inverting input of the on-chip error amplifier. Common-mode range 1.5 V to 5.2 V; open-loop gain 75 dB typ, CMRR 75 dB typ, PSRR 60 dB typ. |+| 3 | Sync | bidirectional | Oscillator sync pin - can be driven by an external clock (~3.5 V, ~1 mA typ, 2.0 V threshold typ) to synchronize the SG3525A to a master clock, or used as a master output to slave additional devices. |+| 4 | OSC. Output | output | Oscillator clock output (3.0-3.5 V amplitude typ). Provides a buffered version of the internal clock for external monitoring or slaving other devices. |+| 5 | CT | passive | Oscillator timing capacitor connection. Recommended range 0.001 µF to 0.2 µF. Together with RT and RD sets oscillator frequency (100 Hz to 400 kHz). |+| 6 | RT | passive | Oscillator timing resistor connection. Recommended range 2.0 kΩ to 150 kΩ. Sets oscillator charging current (2.0 mA typ at IRT = 2.0 mA). |+| 7 | Discharge | passive | Oscillator discharge / dead-time pin. External resistor RD (0 to 500 Ω) between CT (pin 5) and Discharge sets the dead-time (blanking interval) between the two outputs. |+| 8 | Soft-Start | passive | Soft-start capacitor connection. Internal 50 µA current source charges an external capacitor at power-up to ramp the PWM duty cycle from 0 % to maximum, giving controlled start-up. Soft-start current 25-80 µA (50 µA typ). |+| 9 | Compensation | output | Error-amplifier output / PWM comparator input; loop-compensation node. Connect RC network here for feedback loop shaping. PWM comparator thresholds: 0.9 V (zero duty) to 3.3 V (max duty). |+| 10 | Shutdown | input | Active-high shutdown input. A high level (>2.0 V) immediately latches both outputs off via the PWM latch and begins discharging the soft-start capacitor (~100 µA). Should not be left floating due to noise-coupling risk. Input current 0.4 mA typ at 2.5 V. |+| 11 | Output A | output | Totem-pole PWM output A (one of two alternating outputs). ±400 mA peak drive; VOH ≈ 18 V and VOL ≈ 0.2 V at 20 mA (VCC = 20 V). Rise/fall times ~100/50 ns typ into 1 nF. Drives MOSFET gates or bipolar bases directly. |+| 12 | Ground | power_in | Signal and power ground return for the device. |+| 13 | VC | power_in | Output-stage collector supply (separate from VCC). Recommended range 4.5 V to 35 V; allows the output-driver rail to be sourced from a different supply than the control-section VCC. |+| 14 | Output B | output | Totem-pole PWM output B (alternates with Output A each oscillator cycle). ±400 mA peak drive; same VOH/VOL and switching characteristics as Output A. |+| 15 | VCC | power_in | Main IC supply. Recommended range 8.0 V to 35 V (absolute max 40 V). Under-voltage lockout trips at 6.0-8.0 V (7.0 V typ). Supply current ~14 mA typ at VCC = 35 V. |+| 16 | Vref | power_out | Internal 5.1 V ± 1 % voltage reference output. Rated 0-20 mA load; short-circuit current 80 mA typ. Bypass with 0.1 µF to ground; may be tied to error-amp input for reference-based feedback. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | IDCHIP |+| Package | SOP-16 |+| Category | PMIC |+| Pins | 16 |++## Ordering variants++Same part, different packaging or reel option.++- `SG3525ADW`+- `SG3525AN`+- `SG3527AN`++## CAD (KiCad official)++- Symbol: `SG3525A`+- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`+- 3D model: SOP-16 (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [IDCHIP datasheet](docs/sg3525a-datasheet.pdf) (7 pp, sha256 `7bf1f64c1c7ad0d3`, retrieved 2026-08-17, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/sg3525a-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "sg3525a",+ "version": "0.1.0",+ "type": "component",+ "description": "IDCHIP AC-DC Controllers and Regulators, SOP-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "pmic",+ "sg3525a"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "sg3525a.kicad_sym",+ "sg3525a.kicad_mod",+ "sg3525a.glb",+ "sg3525a.step",+ "sg3525a.lbr",+ "docs/hero.png",+ "docs/sg3525a-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}