SG2525AP013TR

@@ -26,7 +26,9 @@       "model_3d_step": "sg2525ap013tr.step",       "lbr": "sg2525ap013tr.lbr"     },-    "distributor_links": {},+    "distributor_links": {+      "lcsc": "C62812"+    },     "pins": [       {         "number": "1",@@ -38,7 +40,7 @@         "number": "2",         "name": "N.I.INPUT",         "type": "input",-        "description": "Non-inverting input of the error amplifier. Typical input bias current 1 µA, input offset voltage 0.5 mV."+        "description": "Non-inverting input of the error amplifier. Typical input bias current 1 \u00b5A, input offset voltage 0.5 mV."       },       {         "number": "3",@@ -56,25 +58,25 @@         "number": "5",         "name": "CT",         "type": "passive",-        "description": "Oscillator timing capacitor connection. External CT to ground (0.001 µF to 0.1 µF) sets the oscillator frequency together with RT per f = 1/(CT·(0.7·RT + 3·RD))."+        "description": "Oscillator timing capacitor connection. External CT to ground (0.001 \u00b5F to 0.1 \u00b5F) sets the oscillator frequency together with RT per f = 1/(CT\u00b7(0.7\u00b7RT + 3\u00b7RD))."       },       {         "number": "6",         "name": "RT",         "type": "passive",-        "description": "Oscillator timing resistor connection. External RT to ground (2 kΩ to 150 kΩ) sets the CT charging current, defining the oscillator frequency (100 Hz to 400 kHz range)."+        "description": "Oscillator timing resistor connection. External RT to ground (2 k\u03a9 to 150 k\u03a9) sets the CT charging current, defining the oscillator frequency (100 Hz to 400 kHz range)."       },       {         "number": "7",         "name": "DISCHARGE",         "type": "passive",-        "description": "Deadtime / discharge resistor terminal. A resistor RD (0 to 500 Ω) between CT (pin 5) and DISCHARGE sets the CT discharge time, providing adjustable deadtime between the two outputs."+        "description": "Deadtime / discharge resistor terminal. A resistor RD (0 to 500 \u03a9) between CT (pin 5) and DISCHARGE sets the CT discharge time, providing adjustable deadtime between the two outputs."       },       {         "number": "8",         "name": "SOFT-START",         "type": "passive",-        "description": "Soft-start capacitor terminal. Internally source-pulled (~50 µA typical) to charge an external capacitor and ramp the PWM duty cycle from zero on start-up; also discharged during shutdown."+        "description": "Soft-start capacitor terminal. Internally source-pulled (~50 \u00b5A typical) to charge an external capacitor and ramp the PWM duty cycle from zero on start-up; also discharged during shutdown."       },       {         "number": "9",@@ -86,13 +88,13 @@         "number": "10",         "name": "SHUTDOWN",         "type": "input",-        "description": "PWM shutdown input. A positive signal (threshold 0.6-1 V, typical 0.8 V) immediately terminates PWM output via the latch and begins discharging the soft-start capacitor (150 µA sink). Should not be left floating; tie low if unused."+        "description": "PWM shutdown input. A positive signal (threshold 0.6-1 V, typical 0.8 V) immediately terminates PWM output via the latch and begins discharging the soft-start capacitor (150 \u00b5A sink). Should not be left floating; tie low if unused."       },       {         "number": "11",         "name": "OUTPUT A",         "type": "output",-        "description": "Totem-pole PWM output A. Alternates with OUTPUT B at half the oscillator frequency. Capable of sourcing/sinking >200 mA (peak 400 mA), rise/fall times ~100/50 ns into 1 nF. VOH = VC − 1 V typ at 100 mA source."+        "description": "Totem-pole PWM output A. Alternates with OUTPUT B at half the oscillator frequency. Capable of sourcing/sinking >200 mA (peak 400 mA), rise/fall times ~100/50 ns into 1 nF. VOH = VC \u2212 1 V typ at 100 mA source."       },       {         "number": "12",@@ -104,7 +106,7 @@         "number": "13",         "name": "VC",         "type": "power_in",-        "description": "Collector supply for the totem-pole output driver stages. Separate from VI to allow the output drivers to be powered from a different rail (4.5 V to 35 V; absolute max 40 V). Bypass with 0.1 µF close to the pin."+        "description": "Collector supply for the totem-pole output driver stages. Separate from VI to allow the output drivers to be powered from a different rail (4.5 V to 35 V; absolute max 40 V). Bypass with 0.1 \u00b5F close to the pin."       },       {         "number": "14",@@ -122,7 +124,7 @@         "number": "16",         "name": "VREF",         "type": "power_out",-        "description": "Internal 5.1 V reference output (trimmed to ±1 %). Short-circuit limited to ~80 mA typical; load current 0 to 20 mA. Bypass with 0.1 µF to ground close to the pin."+        "description": "Internal 5.1 V reference output (trimmed to \u00b11 %). Short-circuit limited to ~80 mA typical; load current 0 to 20 mA. Bypass with 0.1 \u00b5F to ground close to the pin."       }     ],     "provenance": {