← Commit history
README.mdadded+118@@ -0,0 +1,118 @@+# RTS5411T-GR++**Realtek Semicon** · USB Converters · QFN-76(9x9)++RTS5411T-GR from Realtek Semicon, in a QFN-76(9x9). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | RREF | passive | Bandgap reference. Connect an external 6.2K ohm (+/-1%) resistor from this pin to reference GND. |+| 2 | BPWR_DET | input | Upstream VBUS power detection pin. Active High (5V input buffer). 0 = upstream VBUS absent, 1 = upstream VBUS present. |+| 3 | DV11 | power_in | 1.1V power supply for digital circuits. |+| 4 | DV33 | power_in | 3.3V power supply for digital circuits (2.97-3.63V). |+| 5 | DSP2_DP | bidirectional | USB 2.0 D+ signal of Downstream Port 2. |+| 6 | DSP2_DM | bidirectional | USB 2.0 D- signal of Downstream Port 2. |+| 7 | AV11 | power_in | 1.1V power supply for analog circuits. |+| 8 | DSP2_SSTX+ | output | USB 3.2 Gen1x1 SuperSpeed TX+ of Downstream Port 2. |+| 9 | DSP2_SSTX- | output | USB 3.2 Gen1x1 SuperSpeed TX- of Downstream Port 2. |+| 10 | OCP2 | input | Over-current protection flag for downstream port 2. 5V input buffer with internal 10K pull-up (valid in 'power switch' mode). Active low by default (F/W-configurable). 0 = over-current detected. |+| 11 | DSP2_SSRX+ | input | USB 3.2 Gen1x1 SuperSpeed RX+ of Downstream Port 2. |+| 12 | DSP2_SSRX- | input | USB 3.2 Gen1x1 SuperSpeed RX- of Downstream Port 2. |+| 13 | AV11 | power_in | 1.1V power supply for analog circuits. |+| 14 | DSP3_SSTX+ | output | USB 3.2 Gen1x1 SuperSpeed TX+ of Downstream Port 3. |+| 15 | DSP3_SSTX- | output | USB 3.2 Gen1x1 SuperSpeed TX- of Downstream Port 3. |+| 16 | OCP3 | input | Over-current protection flag for downstream port 3. 5V input buffer with internal 10K pull-up (valid in 'power switch' mode). Active low by default. 0 = over-current detected. |+| 17 | DSP3_SSRX+ | input | USB 3.2 Gen1x1 SuperSpeed RX+ of Downstream Port 3. |+| 18 | DSP3_SSRX- | input | USB 3.2 Gen1x1 SuperSpeed RX- of Downstream Port 3. |+| 19 | AV11 | power_in | 1.1V power supply for analog circuits. |+| 20 | DSP3_DP | bidirectional | USB 2.0 D+ signal of Downstream Port 3. |+| 21 | DSP3_DM | bidirectional | USB 2.0 D- signal of Downstream Port 3. |+| 22 | DV33 | power_in | 3.3V power supply for digital circuits. |+| 23 | DSP4_DP | bidirectional | USB 2.0 D+ signal of Downstream Port 4. |+| 24 | DSP4_DM | bidirectional | USB 2.0 D- signal of Downstream Port 4. |+| 25 | AV11 | power_in | 1.1V power supply for analog circuits. |+| 26 | DSP4_SSTX+ | output | USB 3.2 Gen1x1 SuperSpeed TX+ of Downstream Port 4. |+| 27 | DSP4_SSTX- | output | USB 3.2 Gen1x1 SuperSpeed TX- of Downstream Port 4. |+| 28 | OCP4 | input | Over-current protection flag for downstream port 4. 5V input buffer with internal 10K pull-up. Active low by default. 0 = over-current detected. |+| 29 | DSP4_SSRX+ | input | USB 3.2 Gen1x1 SuperSpeed RX+ of Downstream Port 4. |+| 30 | DSP4_SSRX- | input | USB 3.2 Gen1x1 SuperSpeed RX- of Downstream Port 4. |+| 31 | AV11 | power_in | 1.1V power supply for analog circuits. |+| 32 | GPIO0/SMBCL | bidirectional | General purpose I/O with weak internal 200K pull-up, 3.3V buffer. Default: LED for downstream port transmit/receive activity. Configurable as the SMBus clock (SMBCL) pin. |+| 33 | GPIO1/SMBDA | bidirectional | General purpose I/O with weak internal 200K pull-up, 3.3V buffer. Default: LED for downstream port over-current condition. Configurable as the SMBus data (SMBDA) pin. |+| 34 | GPIO2/SCL | bidirectional | General purpose I/O with weak internal 200K pull-up, 3.3V buffer. Default: LED for downstream port transmit/receive activity. Configurable as the I2C clock (SCL) pin. |+| 35 | GPIO3/SDA | bidirectional | General purpose I/O with weak internal 200K pull-up, 3.3V buffer. Default: LED for downstream port over-current condition. Configurable as the I2C data (SDA) pin. |+| 36 | GPIO4 | bidirectional | General purpose I/O with weak internal 200K pull-up, 3.3V buffer. Default: LED for downstream port transmit/receive activity. Leave floating if unused. |+| 37 | GPIO5 | bidirectional | General purpose I/O with weak internal 200K pull-up, 3.3V buffer. Default: LED for downstream port over-current condition. |+| 38 | GPIO6 | bidirectional | General purpose I/O with weak internal 200K pull-up, 3.3V buffer. Default: LED for downstream port transmit/receive activity. |+| 39 | GPIO7 | bidirectional | General purpose I/O with weak internal 200K pull-up, 3.3V buffer. Default: LED for downstream port over-current condition. |+| 40 | DSP1_PWR | output | External VBUS power switch enable for downstream port 1. Open-drain output, active low by default (F/W can configure active high; then uses 3.3V push-pull). 0 = VBUS on, 1 = VBUS off. Leave floating if unused. |+| 41 | DSP2_PWR | output | External VBUS power switch enable for downstream port 2. Open-drain, active low by default. 0 = VBUS on, 1 = VBUS off. |+| 42 | DSP3_PWR | output | External VBUS power switch enable for downstream port 3. Open-drain, active low by default. 0 = VBUS on, 1 = VBUS off. |+| 43 | DSP4_PWR | output | External VBUS power switch enable for downstream port 4. Open-drain, active low by default. 0 = VBUS on, 1 = VBUS off. |+| 44 | SCK | output | SPI clock output to external Serial Flash memory. 3.3V bi-directional buffer. |+| 45 | SCS | output | SPI chip-select output to external Serial Flash memory. 3.3V bi-directional buffer. Also sampled at power-on reset as a strap: 0 = execute code from internal ROM, 1 = execute code from external Serial Flash. |+| 46 | MISO | input | SPI data input from external Serial Flash memory. 3.3V bi-directional buffer. |+| 47 | MOSI | output | SPI data output to external Serial Flash memory. 3.3V bi-directional buffer. |+| 48 | DV33 | power_in | 3.3V power supply for digital circuits. |+| 49 | DV11 | power_in | 1.1V power supply for digital circuits. |+| 50 | DV11 | power_in | 1.1V power supply for digital circuits. |+| 51 | SWR_GND | power_in | Reference ground for the internal 1.1V switching regulator. |+| 52 | SWR_OUT | power_out | 5V-to-1.1V internal switching regulator output. Leave floating if internal switching regulator is not used. |+| 53 | SWR_V5_IN | power_in | 5V-to-1.1V switching regulator input (3.1-5.5V). Connect to LDO_V5_IN when internal switching regulator is not used. |+| 54 | LDO_V5_IN | power_in | 5V-to-3.3V internal LDO input (4.5-5.5V). Short to DV33 when on-chip LDO is not used. |+| 55 | V33_OUT | power_out | 3.3V output from the internal 5V-to-3.3V LDO. Short to DV33 when on-chip LDO is not used. |+| 56 | USP_DP | bidirectional | USB 2.0 D+ signal of the Upstream Port. |+| 57 | USP_DM | bidirectional | USB 2.0 D- signal of the Upstream Port. |+| 58 | AV11 | power_in | 1.1V power supply for analog circuits. |+| 59 | USP_SSTX- | output | USB 3.2 Gen1x1 SuperSpeed TX- of the Upstream Port. |+| 60 | USP_SSTX+ | output | USB 3.2 Gen1x1 SuperSpeed TX+ of the Upstream Port. |+| 61 | GND | power_in | Reference ground. |+| 62 | USP_SSRX- | input | USB 3.2 Gen1x1 SuperSpeed RX- of the Upstream Port. |+| 63 | USP_SSRX+ | input | USB 3.2 Gen1x1 SuperSpeed RX+ of the Upstream Port. |+| 64 | AV11 | power_in | 1.1V power supply for analog circuits. |+| 65 | DSP1_SSTX+ | output | USB 3.2 Gen1x1 SuperSpeed TX+ of Downstream Port 1. |+| 66 | DSP1_SSTX- | output | USB 3.2 Gen1x1 SuperSpeed TX- of Downstream Port 1. |+| 67 | OCP1 | input | Over-current protection flag for downstream port 1. 5V input buffer with internal 10K pull-up. Active low by default. 0 = over-current detected. |+| 68 | DSP1_SSRX+ | input | USB 3.2 Gen1x1 SuperSpeed RX+ of Downstream Port 1. |+| 69 | DSP1_SSRX- | input | USB 3.2 Gen1x1 SuperSpeed RX- of Downstream Port 1. |+| 70 | AV11 | power_in | 1.1V power supply for analog circuits. |+| 71 | DSP1_DP | bidirectional | USB 2.0 D+ signal of Downstream Port 1. |+| 72 | DSP1_DM | bidirectional | USB 2.0 D- signal of Downstream Port 1. |+| 73 | DV33 | power_in | 3.3V power supply for digital circuits. |+| 74 | XTLI | input | 12 MHz crystal oscillator input. 3.3V clock interface. |+| 75 | XTLO | output | 12 MHz crystal oscillator output/drive. 3.3V clock interface. |+| 76 | SPWR_DET | input | Self-power detection pin. 5V input buffer, active high. 0 = bus-power setting, 1 = self-power setting. |+| EP | E-PAD | power_in | Exposed thermal pad on the bottom of the package. Must be connected to reference ground for thermal dissipation and electrical grounding. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Realtek Semicon |+| Package | QFN-76(9x9) |+| Category | Interface |+| Pins | 77 |++## Ordering variants++Same part, different packaging or reel option.++- `RTS5411T-GR`++## CAD (KiCad official)++- Symbol: `RTS5411T-GR`+- Footprint: `Package_DFN_QFN:QFN-76-1EP_9x9mm_P0.4mm_EP3.8x3.8mm`+- 3D model: QFN-76(9x9) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Realtek Semicon datasheet](docs/rts5411t-gr-datasheet.pdf) (32 pp, sha256 `371452f35b4a4904`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/rts5411t-gr-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "rts5411t-gr",+ "version": "0.1.0",+ "type": "component",+ "description": "Realtek Semicon USB Converters, QFN-76(9x9). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "interface",+ "rts5411t-gr"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "rts5411t-gr.kicad_sym",+ "rts5411t-gr.kicad_mod",+ "rts5411t-gr.glb",+ "rts5411t-gr.step",+ "rts5411t-gr.lbr",+ "docs/hero.png",+ "docs/rts5411t-gr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}