component
RT9048GSP
Public Made by Adomby adom
Richtek Tech Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, SOIC-8. Pinout extracted from the datasheet, KiCad symbol/footprint/3D.
← Commit history
page.json+9−6@@ -38,13 +38,13 @@ "number": "2", "name": "EN", "type": "input",- "description": "Enable control input (Active-High). Pulling below 0.4V turns the regulator off, reducing quiescent current to ~1.5\u03bcA. Enable threshold typ. 1.08V rising / 1.02V falling at VIN=3.3V. Device is enabled if left open; connect to VIN if not used."+ "description": "Enable control input (Active-High). Pulling below 0.4V turns the regulator off, reducing quiescent current to ~1.5μA. Enable threshold typ. 1.08V rising / 1.02V falling at VIN=3.3V. Device is enabled if left open; connect to VIN if not used." }, { "number": "3", "name": "VIN", "type": "power_in",- "description": "Supply voltage input. For full-load regulation, input must be between (VOUT + 0.5V) and 6V. Minimum input voltage is 1.4V. Place a large bulk cap plus at least a 10\u03bcF ceramic capacitor directly at this pin."+ "description": "Supply voltage input. For full-load regulation, input must be between (VOUT + 0.5V) and 6V. Minimum input voltage is 1.4V. Place a large bulk cap plus at least a 10μF ceramic capacitor directly at this pin." }, { "number": "4",@@ -62,13 +62,13 @@ "number": "6", "name": "VOUT", "type": "power_out",- "description": "Regulated output voltage, adjustable from 0.5V up to VIN \u2212 VDROP, sourcing up to 2A. Place a minimum 10\u03bcF ceramic capacitor directly at this pin for stability."+ "description": "Regulated output voltage, adjustable from 0.5V up to VIN − VDROP, sourcing up to 2A. Place a minimum 10μF ceramic capacitor directly at this pin for stability." }, { "number": "7", "name": "ADJ", "type": "input",- "description": "Feedback voltage input, VADJ = 0.5V (typ). If tied to VOUT, output is set to 0.5V. Otherwise VOUT = 0.5V \u00d7 (1 + R1/R2) via an external resistor divider. Very low IADJ (~20nA) permits divider resistors up to 800k\u03a9."+ "description": "Feedback voltage input, VADJ = 0.5V (typ). If tied to VOUT, output is set to 0.5V. Otherwise VOUT = 0.5V × (1 + R1/R2) via an external resistor divider. Very low IADJ (~20nA) permits divider resistors up to 800kΩ." }, { "number": "8",@@ -80,7 +80,7 @@ "number": "9", "name": "GND", "type": "power_in",- "description": "Exposed thermal pad (bottom of package). Must be soldered to a large PCB ground plane and connected to GND for maximum power dissipation (\u03b8JA = 49\u00b0C/W on a 4-layer JEDEC board)."+ "description": "Exposed thermal pad (bottom of package). Must be soldered to a large PCB ground plane and connected to GND for maximum power dissipation (θJA = 49°C/W on a 4-layer JEDEC board)." } ], "provenance": {@@ -144,5 +144,8 @@ "docs/rt9048gsp-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }