← Commit history
README.md+36−24
@@ -2,7 +2,7 @@  **Texas Instruments** · Linear Voltage Regulators (LDO) · SOT-223-4 -REG1117 from Texas Instruments, in a SOT-223-4. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.+REG1117 from Texas Instruments, in a SOT-223-4. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.  ## Pinout @@ -11,7 +11,6 @@ REG1117 from Texas Instruments, in a SOT-223-4. Pinout and pin descriptions extr | 1 | ADJ | power_in | Ground terminal on fixed-voltage models and the Adj. feedback terminal on adjustable models, where the output is set by R1 and R2 with about 50µA typical adjustable pin current (120µA max at IO=10mA). | | 2 | VOUT | power_out | Regulated output that needs an output capacitor, with a 10µF tantalum recommended and ESR below 0.5Ω, and it sources up to 800mA (REG1117) or 1A (REG1117A). | | 3 | VIN | power_in | Unregulated input with an absolute maximum of +15V, and dropout is 1.2V max at 800mA for REG1117 or 1.3V max at 1A for REG1117A. |-| 4 | TAB | power_out | Mounting tab electrically connected to VOUT that must be soldered to a copper area to act as the main heat-sink path. |  ## Key specifications @@ -20,7 +19,7 @@ REG1117 from Texas Instruments, in a SOT-223-4. Pinout and pin descriptions extr | Manufacturer | Texas Instruments | | Package | SOT-223-4 | | Category | Power Supply Chip |-| Pins | 4 |+| Pins | 3 |  ## Electrical characteristics @@ -28,26 +27,39 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  | Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page | |---|---|---|---|---|---|---|---|-| Input voltage (absolute maximum) |  |  |  | 15 | V |  | 2 |+| Reference voltage (adjustable), IO=10mA |  | 1.238 | 1.25 | 1.262 | V | IO = 10mA, VIN − VO = 2V | 4 |+| Reference voltage (adjustable), over temperature |  | 1.225 | 1.25 | 1.28 | V | See Note 1: IO = 10 to 800mA, VIN − VO = 1.4 to 10V | 4 |+| Current limit, REG1117 models |  | 800 | 950 | 1200 | mA | VIN − VO = 5V | 5 |+| Dropout voltage, all models |  |  | 1 | 1.1 | V | IO = 100mA | 4 |+| Dropout voltage, all models |  |  | 1.05 | 1.15 | V | See Note 1: IO = 500mA | 4 |+| Dropout voltage, REG1117 models |  |  | 1.1 | 1.2 | V | IO = 800mA | 4 |+| Line regulation, REG1117 (adjustable) |  |  | 0.1 | 0.4 | % | IO = 10mA, VIN − VO = 1.5 to 13.75V | 4 |+| Load regulation, REG1117 (adjustable) |  |  | 0.1 | 0.4 | % | IO = 10 to 800mA, VIN − VO = 3V | 4 |+| Minimum load current, adjustable models |  |  | 1.7 | 5 | mA | VIN − VO = 13.75V | 5 |+| Adjustable pin current |  |  | 50 | 120 | µA | IO = 10mA, VIN − VO = 1.4 to 10V | 5 |+| Adjustable pin current change vs load current, REG1117 |  |  | 0.5 | 5 | µA | IO = 10mA to 800mA, VIN − VO = 1.4 to 10V | 5 |+| Thermal regulation, all models |  |  | 0.01 | 0.1 | %/W | 30ms pulse | 5 |+| Input voltage |  |  |  | 15 | V |  | 2 | | Operating junction temperature range | TJ | -40 |  | 125 | °C |  | 2 | | Storage temperature range |  | -65 |  | 150 | °C |  | 2 |-| Lead temperature (soldering) |  |  |  | 300 | °C | 10s | 2 |-| Reference voltage (REG1117 Adjustable) |  | 1.238 | 1.25 | 1.262 | V | IO = 10mA, VIN − VO = 2V | 4 |-| Reference voltage (REG1117 Adjustable), over load and line |  | 1.225 | 1.25 | 1.28 | V | IO = 10 to 800mA, VIN − VO = 1.4 to 10V | 4 |-| Line regulation (REG1117 Adjustable) |  |  | 0.1 | 0.4 | % | IO = 10mA, VIN − VO = 1.5 to 13.75V | 4 |-| Load regulation (REG1117 Adjustable) |  |  | 0.1 | 0.4 | % | IO = 10 to 800mA, VIN − VO = 3V | 4 |-| Dropout voltage (All Models) |  |  | 1 | 1.1 | V | IO = 100mA | 4 |-| Dropout voltage (All Models) |  |  | 1.05 | 1.15 | V | IO = 500mA | 4 |-| Dropout voltage (REG1117 Models) |  |  | 1.1 | 1.2 | V | IO = 800mA | 4 |-| Current limit (REG1117 Models) |  | 800 | 950 | 1200 | mA | VIN − VO = 5V | 5 |-| Minimum load current (Adjustable Models) |  |  | 1.7 | 5 | mA | VIN − VO = 13.75V | 5 |-| Adjustable pin current |  |  | 50 | 120 | µA | IO = 10mA, VIN − VO = 1.4 to 10V | 5 |-| Adjustable pin current change vs load current (REG1117) |  |  | 0.5 | 5 | µA | IO = 10mA to 800mA, VIN − VO = 1.4 to 10V | 5 |-| Thermal regulation (All Models) |  |  | 0.01 | 0.1 | %/W | 30ms pulse | 5 |-| Thermal shutdown activation temperature | TJ |  | 165 |  | °C | approximately (text) | 8 |-| Thermal resistance, junction-to-case at tab, 3-lead SOT-223 | JC |  | 15 |  | °C/W |  | 5 |-| Thermal resistance, junction-to-ambient, SOT-223, without backside copper (Figure 5 layout) | JA |  | 59 |  | °C/W | Without backside copper | 10 |-| Thermal resistance, junction-to-ambient, SOT-223, with solid backside copper (Figure 5 layout) | JA |  | 49 |  | °C/W | With solid backside copper | 10 |+| Lead temperature |  |  |  | 300 | °C | Soldering, 10s | 2 |+| Ripple rejection, all models |  |  | 62 |  | dB | f = 120Hz, VIN − VOUT = 3V + 1VPP ripple | 5 |+| Temperature drift, adjustable models |  |  | 2 |  | % | TJ = 0°C to +125°C | 5 |+| Long-term stability, all models |  |  | 0.3 |  | % | TA = 125°C, 1000Hr | 5 |+| Output noise, rms, all models |  |  | 0.003 |  | % | f = 10Hz to 10kHz | 5 |+| Thermal resistance junction-to-case at tab, 3-lead SOT-223 | JC |  | 15 |  | °C/W | Junction-to-case at tab | 5 |+| Thermal shutdown activation temperature | TJ |  | 165 |  | °C | Approximately | 8 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 46 |  | °C/W | Total PC board area 2500mm2; topside copper 2500mm2; backside copper 2500mm2 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 47 |  | °C/W | Total PC board area 2500mm2; topside copper 1250mm2; backside copper 2500mm2 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 49 |  | °C/W | Total PC board area 2500mm2; topside copper 950mm2; backside copper 2500mm2 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 51 |  | °C/W | Total PC board area 2500mm2; topside copper 2500mm2; backside copper 0 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 53 |  | °C/W | Total PC board area 2500mm2; topside copper 1800mm2; backside copper 0 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 55 |  | °C/W | Total PC board area 1600mm2; topside copper 600mm2; backside copper 1600mm2 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 58 |  | °C/W | Total PC board area 2500mm2; topside copper 1250mm2; backside copper 0 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 59 |  | °C/W | Total PC board area 2500mm2; topside copper 915mm2; backside copper 0 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 67 |  | °C/W | Total PC board area 1600mm2; topside copper 600mm2; backside copper 0 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 72 |  | °C/W | Total PC board area 900mm2; topside copper 340mm2; backside copper 900mm2 | 10 |+| Thermal resistance junction-to-ambient, SOT-223 board configuration | JA |  | 85 |  | °C/W | Total PC board area 900mm2; topside copper 340mm2; backside copper 0 | 10 |  ## Materials and finish @@ -60,7 +72,7 @@ As the datasheet states them (page.json `metadata.appearance`; the 3D model's co ## CAD (KiCad official)  - Symbol: `REG1117`-- Footprint: `Package_TO_SOT_SMD:SOT-223`+- Footprint: `Package_TO_SOT_SMD:SOT-223-3_TabPin2` - 3D model: SOT-223-4 (KiCad packages3D, STEP) - 3D model files: `reg1117-etched.step` / `reg1117-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `reg1117.step` / `reg1117.glb` are the bare package body. @@ -68,8 +80,8 @@ As the datasheet states them (page.json `metadata.appearance`; the 3D model's co  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/reg1117.pdf) (23 pp, sha256 `9612deef2bd34399`, retrieved 2026-10-30, tier: manufacturer)-- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/reg1117.pdf) (23 pp, sha256 `9612deef2bd34399`, retrieved 2026-11-13, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - **CAD:** KiCad official libraries (CC-BY-SA 4.0).  [Datasheet PDF](docs/reg1117-datasheet.pdf)
package.json+15−35
@@ -1,8 +1,8 @@ {   "slug": "reg1117",-  "version": "0.1.0",+  "version": "0.2.0",   "type": "component",-  "description": "Texas Instruments Linear Voltage Regulators (LDO), SOT-223-4. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "description": "Texas Instruments Linear Voltage Regulators (LDO), SOT-223-4. Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.",   "tags": [     "component",     "power supply chip",@@ -28,14 +28,15 @@     "viewers/symbol.html",     "viewers/footprint.html",     "reg1117-hero.glb",-    "reg1117-hero.overlay.json",-    "reg1117-etched.glb"+    "reg1117-hero.overlay.json"   ],   "component": {-    "mpn": "REG1117",+    "mpn": "REG1117/2K5",+    "land_source": "kicad",+    "land_note": "KiCad SOT-223-3_TabPin2: the tab is pad 2, the maker ties it to pin 2's signal; SOT-223 rule (b), part-reviewer / task master 2026-11-13: the maker prints pins 1-3 and ties the tab to pin 2 ('Tab is VOUT')",     "manufacturer": "Texas Instruments",     "package": "SOT-223-4",-    "pin_count": 4,+    "pin_count": 3,     "category": "Power Supply Chip",     "subcategory": "Linear Voltage Regulators (LDO)",     "datasheet": "https://www.ti.com/lit/ds/symlink/reg1117.pdf",@@ -43,7 +44,7 @@       "symbol": "reg1117.kicad_sym",       "footprint": "reg1117.kicad_mod",       "model_3d": "reg1117-hero.glb",-      "model_3d_plain": "reg1117-etched.glb",+      "model_3d_plain": "reg1117.glb",       "model_3d_step": "reg1117-etched.step",       "model_3d_step_plain": "reg1117.step",       "lbr": "reg1117.lbr"@@ -53,7 +54,7 @@       "mouser": "595-REG1117"     },     "distributor_check": {-      "checked_at": "2026-10-30T18:50:13Z",+      "checked_at": "2026-11-13T01:43:50Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": null,@@ -82,31 +83,10 @@         "name": "VIN",         "type": "power_in",         "description": "Unregulated input with an absolute maximum of +15V, and dropout is 1.2V max at 800mA for REG1117 or 1.3V max at 1A for REG1117A."-      },-      {-        "number": "4",-        "name": "TAB",-        "type": "power_out",-        "description": "Mounting tab electrically connected to VOUT that must be soldered to a copper area to act as the main heat-sink path."       }     ],     "provenance": {-      "extractor": "extract_pins 0.3",-      "factory_chain": {-        "factory": "2.0.0",-        "extractor": "extract_pins 0.3",-        "primary_model": "claude-haiku-5-5",-        "primary_mode": "text",-        "consensus_model": "claude-sonnet-5-5",-        "consensus": "agreed",-        "guards": "pin_guards 0.1: passed",-        "guard_notes": [-          "extractor flagged: The extracted text does not print pin numbers 2 and 4 next to their names. The connection diagram li; Pin 1 is ground on fixed-voltage models and the Adj. terminal on the adjustable model. The type is s; The ordering table lists the package as SOT223-3 (DCY), while the package addendum lists it as 4 pin"-        ],-        "pages_sent": 23,-        "cost_usd": 0.0982,-        "at": "2026-10-30T18:50:08"-      },+      "extractor": "ds2sf",       "datasheet": {         "url": "https://www.ti.com/lit/ds/symlink/reg1117.pdf",         "pages": 23,@@ -115,8 +95,8 @@       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {-        "total": 4,-        "described": 4,+        "total": 3,+        "described": 3,         "cites_pages": true,         "refuses_to_fabricate": true       }@@ -142,7 +122,7 @@         "centre_offset_mm": 0.0,         "footprint_binding": "identity",         "sha256": "77ad6dbacc493cb619c728f26d2ddcf461eb0feb6b977b47d01d51e67016f654",-        "checked": "2026-10-30",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -160,8 +140,8 @@         "zmin_mm": -0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "8880c44da7b6d9ca81f87ab4559409024cdff5bfb23b6b07bbe44f7477e4eaea",-        "checked": "2026-10-30",+        "sha256": "5e7e08ba6a79e5bf83915dad2ee34742c2da49d83439380b1aad9ee102d15890",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],
page.json+17−37
@@ -4,7 +4,7 @@   "slug": "reg1117",   "title": "REG1117",   "brief": "Texas Instruments Linear Voltage Regulators (LDO), SOT-223-4. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.2.0",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -14,10 +14,12 @@     "extractor-text"   ],   "component": {-    "mpn": "REG1117",+    "mpn": "REG1117/2K5",+    "land_source": "kicad",+    "land_note": "KiCad SOT-223-3_TabPin2: the tab is pad 2, the maker ties it to pin 2's signal; SOT-223 rule (b), part-reviewer / task master 2026-11-13: the maker prints pins 1-3 and ties the tab to pin 2 ('Tab is VOUT')",     "manufacturer": "Texas Instruments",     "package": "SOT-223-4",-    "pin_count": 4,+    "pin_count": 3,     "category": "Power Supply Chip",     "subcategory": "Linear Voltage Regulators (LDO)",     "datasheet": "https://www.ti.com/lit/ds/symlink/reg1117.pdf",@@ -25,7 +27,7 @@       "symbol": "reg1117.kicad_sym",       "footprint": "reg1117.kicad_mod",       "model_3d": "reg1117-hero.glb",-      "model_3d_plain": "reg1117-etched.glb",+      "model_3d_plain": "reg1117.glb",       "model_3d_step": "reg1117-etched.step",       "model_3d_step_plain": "reg1117.step",       "lbr": "reg1117.lbr"@@ -35,7 +37,7 @@       "mouser": "595-REG1117"     },     "distributor_check": {-      "checked_at": "2026-10-30T18:50:13Z",+      "checked_at": "2026-11-13T01:43:50Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": null,@@ -64,31 +66,10 @@         "name": "VIN",         "type": "power_in",         "description": "Unregulated input with an absolute maximum of +15V, and dropout is 1.2V max at 800mA for REG1117 or 1.3V max at 1A for REG1117A."-      },-      {-        "number": "4",-        "name": "TAB",-        "type": "power_out",-        "description": "Mounting tab electrically connected to VOUT that must be soldered to a copper area to act as the main heat-sink path."       }     ],     "provenance": {-      "extractor": "extract_pins 0.3",-      "factory_chain": {-        "factory": "2.0.0",-        "extractor": "extract_pins 0.3",-        "primary_model": "claude-haiku-5-5",-        "primary_mode": "text",-        "consensus_model": "claude-sonnet-5-5",-        "consensus": "agreed",-        "guards": "pin_guards 0.1: passed",-        "guard_notes": [-          "extractor flagged: The extracted text does not print pin numbers 2 and 4 next to their names. The connection diagram li; Pin 1 is ground on fixed-voltage models and the Adj. terminal on the adjustable model. The type is s; The ordering table lists the package as SOT223-3 (DCY), while the package addendum lists it as 4 pin"-        ],-        "pages_sent": 23,-        "cost_usd": 0.0982,-        "at": "2026-10-30T18:50:08"-      },+      "extractor": "ds2sf",       "datasheet": {         "url": "https://www.ti.com/lit/ds/symlink/reg1117.pdf",         "pages": 23,@@ -97,8 +78,8 @@       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {-        "total": 4,-        "described": 4,+        "total": 3,+        "described": 3,         "cites_pages": true,         "refuses_to_fabricate": true       }@@ -124,7 +105,7 @@         "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "77ad6dbacc493cb619c728f26d2ddcf461eb0feb6b977b47d01d51e67016f654",-        "checked": "2026-10-30",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -142,8 +123,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "8880c44da7b6d9ca81f87ab4559409024cdff5bfb23b6b07bbe44f7477e4eaea",-        "checked": "2026-10-30",+        "sha256": "5e7e08ba6a79e5bf83915dad2ee34742c2da49d83439380b1aad9ee102d15890",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],@@ -495,10 +476,9 @@     "viewers/symbol.html",     "viewers/footprint.html",     "reg1117-hero.glb",-    "reg1117-hero.overlay.json",-    "reg1117-etched.glb"+    "reg1117-hero.overlay.json"   ],-  "visibility": {-    "public": true-  }+  "visibility": "public",+  "description": "Texas Instruments Linear Voltage Regulators (LDO), SOT-223-4. Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file
reg1117-hero.glb
⋯ 1 unchanged line ⋯
reg1117-hero.overlay.json+164−168
@@ -1,172 +1,168 @@ {-  "spec": "adom-hero 1.4",-  "mpn": "REG1117",-  "kind": "component + footprint reference art",-  "board_use": false,-  "plane_z_mm": -0.02,-  "units": "metre",-  "upAxis": "Z",-  "layers": {-    "pad_outlines": {-      "material": "Footprint pads - teal dashed outlines - 50 percent opacity",-      "rgba": [-        0.0,-        0.902,-        0.863,-        0.5-      ],-      "pads": 4,-      "span_mm": 8.4,-      "dash_mm": 0.21,-      "gap_mm": 0.126,-      "pad_stroke_mm": 0.0504-    },-    "silkscreen": {-      "material": "Silkscreen reference lines - 30 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.3-      ],-      "footprint_items": 5,-      "pin1": {-        "source": "footprint silkscreen",-        "pad": "1"-      }-    },-    "signal_names": {-      "material": "Signal names - 50 percent opacity",-      "rgba": [-        0.92,-        0.96,-        1.0,-        0.5-      ],-      "font": "DejaVu Sans Mono",-      "labels": 4,-      "sides": "top + mirrored underside (single-sided)",-      "fallback_to_pad_number": 0-    }+ "spec": "adom-hero 1.4",+ "mpn": "REG1117/2K5",+ "kind": "component + footprint reference art",+ "board_use": false,+ "plane_z_mm": -0.02,+ "units": "metre",+ "upAxis": "Z",+ "layers": {+  "pad_outlines": {+   "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+   "rgba": [+    0.0,+    0.902,+    0.863,+    0.5+   ],+   "pads": 4,+   "span_mm": 8.4,+   "dash_mm": 0.21,+   "gap_mm": 0.126,+   "pad_stroke_mm": 0.0504   },-  "align": {-    "ok": true,-    "centre_offset_mm": 0.0,-    "tolerance_mm": 0.664,-    "orientation_flipped": false,-    "contacts_bbox_mm": [-      -3.5,-      3.5,-      -2.684,-      2.684-    ],-    "pads_bbox_mm": [-      -4.15,-      4.15,-      -3.05,-      3.05-    ],-    "seating_z_mm": 0.0+  "silkscreen": {+   "material": "Silkscreen reference lines - 30 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.3+   ],+   "footprint_items": 5,+   "pin1": {+    "source": "footprint silkscreen",+    "pad": "1"+   }   },-  "sources": {-    "glb": "reg1117-etched.glb",-    "glb_sha256": "fb0546a039fe5069cd7d958e13c6b6ebadc3cb15bcbd7e4a757dff2372745fdb",-    "footprint": "reg1117.kicad_mod",-    "footprint_sha256": "cd4d9acafebc8af47096ec13bdcbb78ddfc4a0db3bacf6989ced0ee482c749b2",-    "pins": "page.json component.pins",-    "pins_sha256": "f41c73b53adf77fbef7cc7f99eb7692a288544c2e09cd394efe034bbf69eb222"-  },-  "generator": "adom-wiki 1.8.2 (component_hero)",-  "labels": [-    {-      "pad": "1",-      "text": "ADJ",-      "x": -4.3,-      "y": -2.3,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "2",-      "text": "VOUT",-      "x": -4.3,-      "y": 0.0,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "3",-      "text": "VIN",-      "x": -4.3,-      "y": 2.3,-      "align": "right",-      "vertical": false,-      "h": 0.6-    },-    {-      "pad": "4",-      "text": "TAB",-      "x": 4.3,-      "y": 0.0,-      "align": "left",-      "vertical": false,-      "h": 0.6-    }+  "signal_names": {+   "material": "Signal names - 50 percent opacity",+   "rgba": [+    0.92,+    0.96,+    1.0,+    0.5+   ],+   "font": "DejaVu Sans Mono",+   "labels": 3,+   "sides": "top + mirrored underside (single-sided)",+   "omitted": null,+   "fallback_to_pad_number": 0+  }+ },+ "align": {+  "ok": true,+  "board_underside": false,+  "electrical_pads_without_contact": [],+  "mounting_pads_left_out": [],+  "centre_offset_mm": 0.0,+  "over_pads": true,+  "tolerance_mm": 0.664,+  "orientation_flipped": false,+  "contacts_bbox_mm": [+   -3.5,+   3.5,+   -2.684,+   2.684+  ],+  "pads_bbox_mm": [+   -4.15,+   4.15,+   -3.05,+   3.05   ],-  "pads": [-    {-      "number": "1",-      "shape": "roundrect",-      "center_mm": [-        -3.15,-        -2.3-      ],-      "size_mm": [-        2.0,-        1.5-      ],-      "rot": 0.0-    },-    {-      "number": "2",-      "shape": "roundrect",-      "center_mm": [-        -3.15,-        0.0-      ],-      "size_mm": [-        2.0,-        1.5-      ],-      "rot": 0.0-    },-    {-      "number": "3",-      "shape": "roundrect",-      "center_mm": [-        -3.15,-        2.3-      ],-      "size_mm": [-        2.0,-        1.5-      ],-      "rot": 0.0-    },-    {-      "number": "4",-      "shape": "roundrect",-      "center_mm": [-        3.15,-        0.0-      ],-      "size_mm": [-        2.0,-        3.8-      ],-      "rot": 0.0-    }-  ]-}+  "seating_z_mm": 0.0+ },+ "sources": {+  "glb": "reg1117-etched.glb",+  "glb_sha256": "fb0546a039fe5069cd7d958e13c6b6ebadc3cb15bcbd7e4a757dff2372745fdb",+  "footprint": "reg1117.kicad_mod",+  "footprint_sha256": "5f6cad94d6c821d01d360a4a09cca4b89e63ae0ce12c33d1dd0ba4e30e86c523",+  "pins": "page.json component.pins",+  "pins_sha256": "0b994e138925263eefd55b81eee80708336253ae6e206dccbf99ff283fe00bdc"+ },+ "generator": "factory/hero_glb.py",+ "labels": [+  {+   "pad": "1",+   "text": "ADJ",+   "x": -4.3,+   "y": -2.3,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "2",+   "text": "VOUT",+   "x": -4.3,+   "y": 0.0,+   "align": "right",+   "vertical": false,+   "h": 0.6+  },+  {+   "pad": "3",+   "text": "VIN",+   "x": -4.3,+   "y": 2.3,+   "align": "right",+   "vertical": false,+   "h": 0.6+  }+ ],+ "pads": [+  {+   "number": "1",+   "shape": "roundrect",+   "center_mm": [+    -3.15,+    -2.3+   ],+   "size_mm": [+    2.0,+    1.5+   ],+   "rot": 0.0+  },+  {+   "number": "2",+   "shape": "roundrect",+   "center_mm": [+    -3.15,+    0.0+   ],+   "size_mm": [+    2.0,+    1.5+   ],+   "rot": 0.0+  },+  {+   "number": "2",+   "shape": "roundrect",+   "center_mm": [+    3.15,+    0.0+   ],+   "size_mm": [+    2.0,+    3.8+   ],+   "rot": 0.0+  },+  {+   "number": "3",+   "shape": "roundrect",+   "center_mm": [+    -3.15,+    2.3+   ],+   "size_mm": [+    2.0,+    1.5+   ],+   "rot": 0.0+  }+ ]+}\ No newline at end of file
reg1117.kicad_mod+32−32
@@ -1,4 +1,4 @@-(footprint "SOT-223"+(footprint "SOT-223-3_TabPin2" 	(version 20260206) 	(generator "pcbnew") 	(generator_version "10.0")@@ -8,7 +8,7 @@ 	(property "Reference" "REF**" 		(at 0 -4.5 0) 		(layer "F.SilkS")-		(uuid "4497a1e1-94b1-4cba-abfc-02d82a04371f")+		(uuid "095b50a5-76ce-476b-aa10-37a37fa441f1") 		(effects 			(font 				(size 1 1)@@ -16,10 +16,10 @@ 			) 		) 	)-	(property "Value" "SOT-223"+	(property "Value" "SOT-223-3_TabPin2" 		(at 0 4.5 0) 		(layer "F.Fab")-		(uuid "222a057b-4f1f-481e-81c0-82276f6e2fbf")+		(uuid "a763838d-1dc3-4eda-bbc0-fbcf1edf1449") 		(effects 			(font 				(size 1 1)@@ -27,12 +27,12 @@ 			) 		) 	)-	(property "Datasheet" "https://www.ti.com/lit/ds/symlink/reg1117.pdf"+	(property "Datasheet" "" 		(at 0 0 0) 		(unlocked yes) 		(layer "F.Fab") 		(hide yes)-		(uuid "cf35375b-a35a-4ccf-b401-52356d4eb3ab")+		(uuid "0fecb949-4744-4c65-8091-70f595847ba4") 		(effects 			(font 				(size 1.27 1.27)@@ -45,7 +45,7 @@ 		(unlocked yes) 		(layer "F.Fab") 		(hide yes)-		(uuid "e0b857b7-85f4-442e-9375-43b7f0b65024")+		(uuid "7dd6192e-e612-428f-816e-6f28697542d5") 		(effects 			(font 				(size 1.27 1.27)@@ -63,7 +63,7 @@ 			(type solid) 		) 		(layer "F.SilkS")-		(uuid "10341b74-de1d-44f8-b919-9dc7b01c77a6")+		(uuid "e98ec803-a6f4-4196-9fa0-d9f7619efa9d") 	) 	(fp_line 		(start -1.85 3.41)@@ -73,7 +73,7 @@ 			(type solid) 		) 		(layer "F.SilkS")-		(uuid "9eaaee9c-d787-4c4e-9409-486f5d803253")+		(uuid "6e43f798-7915-403c-b947-4851bde35045") 	) 	(fp_line 		(start 1.91 -3.41)@@ -83,7 +83,7 @@ 			(type solid) 		) 		(layer "F.SilkS")-		(uuid "668bbda1-c7e1-4e23-9d62-dd4d052018b0")+		(uuid "ddfc40c4-e33c-493e-b735-24282440d539") 	) 	(fp_line 		(start 1.91 3.41)@@ -93,7 +93,7 @@ 			(type solid) 		) 		(layer "F.SilkS")-		(uuid "7b7161b8-bc72-4822-9d67-8c4bc120433f")+		(uuid "79366377-6a9f-460a-b0d1-788467590954") 	) 	(fp_poly 		(pts@@ -105,27 +105,27 @@ 		) 		(fill yes) 		(layer "F.SilkS")-		(uuid "818bd365-7a79-40a2-b037-dacc75b8af05")+		(uuid "27420593-f422-495a-9e17-88a99bcd8a3d") 	) 	(fp_line-		(start -1.85 -2.3)+		(start -1.85 -2.35) 		(end -1.85 3.35) 		(stroke 			(width 0.1) 			(type solid) 		) 		(layer "F.Fab")-		(uuid "2a9ca989-6b38-468d-a714-75a033988b2c")+		(uuid "659fc817-2286-4dd8-ba60-8e62262ce6cc") 	) 	(fp_line-		(start -1.85 -2.3)-		(end -0.8 -3.35)+		(start -1.85 -2.35)+		(end -0.85 -3.35) 		(stroke 			(width 0.1) 			(type solid) 		) 		(layer "F.Fab")-		(uuid "bcb7341f-c5b7-4cf0-ac84-66c574c5e61c")+		(uuid "f393364a-2641-4746-ba4c-6509ea1de503") 	) 	(fp_line 		(start -1.85 3.35)@@ -135,17 +135,17 @@ 			(type solid) 		) 		(layer "F.Fab")-		(uuid "c011dc66-40ad-4f1e-a34f-e251dae0cd31")+		(uuid "27db54e0-f4a8-4972-bcbc-256787416dcd") 	) 	(fp_line-		(start -0.8 -3.35)+		(start -0.85 -3.35) 		(end 1.85 -3.35) 		(stroke 			(width 0.1) 			(type solid) 		) 		(layer "F.Fab")-		(uuid "80711826-0dce-449b-af78-388864936159")+		(uuid "be579ebe-38db-4860-98f0-9f530f704760") 	) 	(fp_line 		(start 1.85 -3.35)@@ -155,12 +155,12 @@ 			(type solid) 		) 		(layer "F.Fab")-		(uuid "a66ee799-671f-4902-ac92-f94d39f82acf")+		(uuid "9d748ff0-f43a-42f3-a9ff-3a463972b1ca") 	) 	(fp_text user "${REFERENCE}" 		(at 0 0 90) 		(layer "F.Fab")-		(uuid "184c46b5-a004-48e0-8f63-d7d63dc324be")+		(uuid "aff1cd04-29c5-47f0-8349-1badf43ec67b") 		(effects 			(font 				(size 0.8 0.8)@@ -173,28 +173,28 @@ 		(size 2 1.5) 		(layers "F.Cu" "F.Mask" "F.Paste") 		(roundrect_rratio 0.25)-		(uuid "ea891fee-0855-44cc-8da9-0c7b9e3b1505")+		(uuid "6c38c733-73aa-46ef-9aa8-0adc47a79448") 	) 	(pad "2" smd roundrect 		(at -3.15 0) 		(size 2 1.5) 		(layers "F.Cu" "F.Mask" "F.Paste") 		(roundrect_rratio 0.25)-		(uuid "2adbaf0f-7617-4618-9438-78a8bd4ec4b2")+		(uuid "553b4aa3-b4fc-45ee-9bbe-5eb8183ee7d8") 	)-	(pad "3" smd roundrect-		(at -3.15 2.3)-		(size 2 1.5)+	(pad "2" smd roundrect+		(at 3.15 0)+		(size 2 3.8) 		(layers "F.Cu" "F.Mask" "F.Paste") 		(roundrect_rratio 0.25)-		(uuid "1b42a1a5-e735-42f2-b87a-1df5a461081d")+		(uuid "118e82e2-9099-4e46-a269-1e2cb8448d5e") 	)-	(pad "4" smd roundrect-		(at 3.15 0)-		(size 2 3.8)+	(pad "3" smd roundrect+		(at -3.15 2.3)+		(size 2 1.5) 		(layers "F.Cu" "F.Mask" "F.Paste") 		(roundrect_rratio 0.25)-		(uuid "023f2cc5-97fb-4421-8e37-e8aa385789b4")+		(uuid "5046df04-2b74-45a5-867e-e33a5e51e59c") 	) 	(embedded_fonts no) 	(model "${KICAD10_3DMODEL_DIR}/Package_TO_SOT_SMD.3dshapes/SOT-223.step"
reg1117.kicad_sym+1−5
@@ -16,11 +16,7 @@       (name "VOUT" (effects (font (size 1.27 1.27))))       (number "2" (effects (font (size 1.27 1.27))))     )-    (pin power_out line (at 17.78 0.00 180) (length 5.08)-      (name "TAB" (effects (font (size 1.27 1.27))))-      (number "4" (effects (font (size 1.27 1.27))))-    )-    (pin power_in line (at 17.78 -2.54 180) (length 5.08)+    (pin power_in line (at 17.78 0.00 180) (length 5.08)       (name "VIN" (effects (font (size 1.27 1.27))))       (number "3" (effects (font (size 1.27 1.27))))     )
reg1117.lbr+8−10
@@ -52,12 +52,12 @@ <library> <description>Texas Instruments Linear Voltage Regulators (LDO), SOT-223-4. Pinout cross-checked by two models against the datasheet</description> <packages>-<package name="SOT-223">+<package name="SOT-223-3_TabPin2">   <description>4 pads, 8.3 x 6.1 mm. module CMS SOT223 4 pins</description>   <smd name="1" x="-3.1500" y="2.3000" dx="2.0000" dy="1.5000" layer="1" roundness="50"/>   <smd name="2" x="-3.1500" y="-0.0000" dx="2.0000" dy="1.5000" layer="1" roundness="50"/>+  <smd name="2@2" x="3.1500" y="-0.0000" dx="2.0000" dy="3.8000" layer="1" roundness="50"/>   <smd name="3" x="-3.1500" y="-2.3000" dx="2.0000" dy="1.5000" layer="1" roundness="50"/>-  <smd name="4" x="3.1500" y="-0.0000" dx="2.0000" dy="3.8000" layer="1" roundness="50"/>   <polygon width="0.1200" layer="21">     <vertex x="-3.1300" y="3.3100"/>     <vertex x="-3.3700" y="3.6400"/>@@ -68,10 +68,10 @@   <wire x1="-1.8500" y1="-3.4100" x2="1.9100" y2="-3.4100" width="0.1200" layer="21"/>   <wire x1="1.9100" y1="3.4100" x2="1.9100" y2="2.1500" width="0.1200" layer="21"/>   <wire x1="1.9100" y1="-3.4100" x2="1.9100" y2="-2.1500" width="0.1200" layer="21"/>-  <wire x1="-1.8500" y1="2.3000" x2="-1.8500" y2="-3.3500" width="0.1000" layer="51"/>-  <wire x1="-1.8500" y1="2.3000" x2="-0.8000" y2="3.3500" width="0.1000" layer="51"/>+  <wire x1="-1.8500" y1="2.3500" x2="-1.8500" y2="-3.3500" width="0.1000" layer="51"/>+  <wire x1="-1.8500" y1="2.3500" x2="-0.8500" y2="3.3500" width="0.1000" layer="51"/>   <wire x1="-1.8500" y1="-3.3500" x2="1.8500" y2="-3.3500" width="0.1000" layer="51"/>-  <wire x1="-0.8000" y1="3.3500" x2="1.8500" y2="3.3500" width="0.1000" layer="51"/>+  <wire x1="-0.8500" y1="3.3500" x2="1.8500" y2="3.3500" width="0.1000" layer="51"/>   <wire x1="1.8500" y1="3.3500" x2="1.8500" y2="-3.3500" width="0.1000" layer="51"/>   <text x="0" y="4.010" size="1.27" layer="25" align="bottom-center">&gt;NAME</text>   <text x="0" y="-4.010" size="1.27" layer="27" align="top-center">&gt;VALUE</text>@@ -88,8 +88,7 @@   <text x="0.0000" y="-7.6200" size="1.27" layer="96" align="center">&gt;VALUE</text>   <pin name="ADJ" x="-17.78" y="0" length="middle" direction="pwr"/>   <pin name="VOUT" x="-17.78" y="-2.54" length="middle" direction="out"/>-  <pin name="TAB" x="17.78" y="0" length="middle" direction="out" rot="R180"/>-  <pin name="VIN" x="17.78" y="-2.54" length="middle" direction="pwr" rot="R180"/>+  <pin name="VIN" x="17.78" y="0" length="middle" direction="pwr" rot="R180"/> </symbol> </symbols> <devicesets>@@ -99,11 +98,10 @@     <gate name="G$1" symbol="REG1117" x="0" y="0"/>   </gates>   <devices>-    <device name="" package="SOT-223">+    <device name="" package="SOT-223-3_TabPin2">       <connects>         <connect gate="G$1" pin="ADJ" pad="1"/>-        <connect gate="G$1" pin="VOUT" pad="2"/>-        <connect gate="G$1" pin="TAB" pad="4"/>+        <connect gate="G$1" pin="VOUT" pad="2 2@2"/>         <connect gate="G$1" pin="VIN" pad="3"/>       </connects>       <technologies>