← Commit history
page.json+10−7@@ -38,25 +38,25 @@ "number": "2", "name": "PROG", "type": "passive",- "description": "Constant-current program and charge-current monitor pin. A resistor R_PROG from PROG to GND sets the fast-charge current: I_BAT = (V_PROG / R_PROG) \u00d7 1200, with V_PROG \u2248 1.0 V in constant-current mode (0.1 V during trickle). Pin voltage may be read to monitor instantaneous charge current. Max sink current 1200 \u00b5A; 2.0 \u00b5A internal pull-up."+ "description": "Constant-current program and charge-current monitor pin. A resistor R_PROG from PROG to GND sets the fast-charge current: I_BAT = (V_PROG / R_PROG) × 1200, with V_PROG ≈ 1.0 V in constant-current mode (0.1 V during trickle). Pin voltage may be read to monitor instantaneous charge current. Max sink current 1200 µA; 2.0 µA internal pull-up." }, { "number": "3", "name": "GND", "type": "power_in",- "description": "Device ground. Also serves as the thermal reference; connect the SOP-8 exposed pad to this net with a low-impedance copper pour to meet the 130 \u00b0C/W \u03b8JA assumed in the datasheet."+ "description": "Device ground. Also serves as the thermal reference; connect the SOP-8 exposed pad to this net with a low-impedance copper pour to meet the 130 °C/W θJA assumed in the datasheet." }, { "number": "4", "name": "Vcc", "type": "power_in",- "description": "Input supply from a USB port or wall adapter, 4.0 V typ 5 V max 6 V (abs-max \u22120.3 V to 7 V). Powers the internal circuitry and the pass FET (R_ON \u2248 650 m\u03a9). When (Vcc \u2212 V_BAT) drops below \u224830 mV the part enters low-power shutdown and the BAT pin sinks less than 2 \u00b5A. Decouple with 10 \u00b5F near the pin."+ "description": "Input supply from a USB port or wall adapter, 4.0 V typ 5 V max 6 V (abs-max −0.3 V to 7 V). Powers the internal circuitry and the pass FET (R_ON ≈ 650 mΩ). When (Vcc − V_BAT) drops below ≈30 mV the part enters low-power shutdown and the BAT pin sinks less than 2 µA. Decouple with 10 µF near the pin." }, { "number": "5", "name": "BAT", "type": "power_out",- "description": "Charge current output to the positive terminal of the single-cell Li-ion / Li-polymer battery. Regulates to the 4.2 V float voltage (4.137-4.263 V) and delivers up to 1200 mA (abs-max) charge current. Leakage into the battery is <2 \u00b5A when the chip is disabled or in sleep. Auto-recharge triggers when V_BAT falls \u2265150 mV below V_FLOAT."+ "description": "Charge current output to the positive terminal of the single-cell Li-ion / Li-polymer battery. Regulates to the 4.2 V float voltage (4.137-4.263 V) and delivers up to 1200 mA (abs-max) charge current. Leakage into the battery is <2 µA when the chip is disabled or in sleep. Auto-recharge triggers when V_BAT falls ≥150 mV below V_FLOAT." }, { "number": "6",@@ -68,13 +68,13 @@ "number": "7", "name": "CHRG", "type": "output",- "description": "Open-drain charge-in-progress indicator (active-low, name is bar-CHRG). Pulled low while the charger is delivering current to the battery; Hi-Z otherwise. With a 10 \u00b5F cap on BAT and no battery installed, pulses at \u22481-4 s to signal a missing battery. V_OL 0.2 V typ at 3 mA sink; abs-max 10 V."+ "description": "Open-drain charge-in-progress indicator (active-low, name is bar-CHRG). Pulled low while the charger is delivering current to the battery; Hi-Z otherwise. With a 10 µF cap on BAT and no battery installed, pulses at ≈1-4 s to signal a missing battery. V_OL 0.2 V typ at 3 mA sink; abs-max 10 V." }, { "number": "8", "name": "CE", "type": "input",- "description": "Chip enable input. Logic high enables normal charging; logic low disables the charger and inhibits current into BAT. TTL and CMOS compatible; abs-max \u22120.3 V to 10 V. Tie to Vcc for always-on operation."+ "description": "Chip enable input. Logic high enables normal charging; logic low disables the charger and inhibits current into BAT. TTL and CMOS compatible; abs-max −0.3 V to 10 V. Tie to Vcc for always-on operation." } ], "provenance": {@@ -138,5 +138,8 @@ "docs/pt4056-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }