← Commit history

Initial commit: component/pl5500

Ray ·e720d978fd ·
2 files changed +107
README.mdadded+73
@@ -0,0 +1,73 @@+# PL5500++**POWLICON** · DC-DC Converters · QFN-32-EP(4x4)++PL5500 from POWLICON, in a QFN-32-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VADJ | input | Programs the voltage reference on VREF using a 0-2 V analog voltage or PWM signal. Tying VADJ to VDD forces VREF to a constant 2 V. |+| 2 | IADJ | input | Programs the current-limit reference on IREF using a 0-2 V analog voltage or PWM signal. Tying IADJ to VDD forces IREF to 2 V. |+| 3 | VSET | bidirectional | In charge mode (OTG low): a resistor from VSET to GND selects battery cell full-charge voltage (4.2/4.35/4.4/4.5 V). In discharge mode (OTG > 1.2 V): VSET outputs a voltage proportional to V(CSP2)-V(CSN2) for host monitoring of discharge current. |+| 4 | IREF | passive | Reference-voltage node for the input and output current-limit loops. Typically bypassed with a small capacitor to GND. |+| 5 | VREF | passive | Reference-voltage node for the voltage-control loop (2 V in discharge, 1.8 V in charge when VADJ = VDD). Typically bypassed to GND. |+| 6 | BRCOM | output | Battery internal-resistance compensation output. Voltage on this pin is proportional to V(CSP1)-V(CSN1) so the host can monitor charging current. |+| 7 | MODE | input | CCM/DCM mode select. Float (weak internal pull-up) selects DCM at light load; tie to GND to force CCM. |+| 8 | STAT | output | Status output. Reports charging status when OTG = Low, and functions as a PGOOD (power-good) indicator when OTG = High. |+| 9 | FREQ | input | Sets switching frequency: tie to GND for 150 kHz, tie to VDD for 300 kHz, or use a resistor divider between VDD/GND for 600 kHz (0.4-0.85 V) or 1200 kHz (0.85-1.8 V). |+| 10 | COMP | passive | Error-amplifier output / loop-compensation node. External RC network to GND sets loop dynamics. |+| 11 | VREG | input | Programs VBUS regulation voltage via a resistor divider. During heavy charging, when VBUS falls near the VREG setpoint the VREG loop takes over and reduces charging current. Not active in discharge mode. |+| 12 | FB2 | input | VBUS voltage feedback in discharge mode. A resistor divider from VBUS to GND sets the regulated VBUS voltage (VFB2 regulation = 2 V). |+| 13 | CSN2 | input | Negative input of the output (VBUS-side) current-sense amplifier. Max V(CSP2)-V(CSN2) is 0.6 V. |+| 14 | CSP2 | input | Positive input of the output (VBUS-side) current-sense amplifier. Max V(CSP2)-V(CSN2) is 0.6 V. |+| 15 | VBUS | power_in | VBUS power rail (3.6-32 V operating, 40 V abs max). Sense/supply for the output-side of the buck-boost stage. |+| 16 | HG2 | output | High-side gate drive 2 (VBUS-side high-side MOSFET). Integrated 2 A driver, referenced to SW2, powered from BST2. |+| 17 | BST2 | passive | Bootstrap capacitor node for HG2. Connect capacitor from BST2 to SW2; abs max BST2-to-SW2 = 7 V. |+| 18 | SW2 | passive | Switching node 2 (VBUS-side inductor terminal / bootstrap return). Abs max -0.3 V to 40 V. |+| 19 | LG2 | output | Low-side gate drive 2 (VBUS-side low-side MOSFET). Integrated 2 A driver referenced to GND, powered from VCC. |+| 20 | VCC | power_in | 5.0 V supply for the high-side and low-side gate drivers. Bypass to GND with a low-ESR capacitor. |+| 21 | LG1 | output | Low-side gate drive 1 (VBAT-side low-side MOSFET). Integrated 2 A driver referenced to GND, powered from VCC. |+| 22 | SW1 | passive | Switching node 1 (VBAT-side inductor terminal / bootstrap return). Abs max -0.3 V to 40 V. |+| 23 | BST1 | passive | Bootstrap capacitor node for HG1. Connect capacitor from BST1 to SW1; abs max BST1-to-SW1 = 7 V. |+| 24 | HG1 | output | High-side gate drive 1 (VBAT-side high-side MOSFET). Integrated 2 A driver, referenced to SW1, powered from BST1. |+| 25 | VBAT | power_in | Battery/input power rail (3.6-32 V operating, 40 V abs max). Also acts as output rail during OTG discharge operation. |+| 26 | CSP1 | input | Positive input of the input/battery-side current-sense amplifier. Max V(CSP1)-V(CSN1) is 0.6 V. |+| 27 | CSN1 | input | Negative input of the input/battery-side current-sense amplifier. Max V(CSP1)-V(CSN1) is 0.6 V. |+| 28 | EN | input | Enable input. Logic high enables the converter; logic low disables the entire PL5500. Weak internal pull-up; threshold ≈1.2 V with 200 mV hysteresis. |+| 29 | CELLS | input | Battery cell-count programming input. Resistor divider between VDD and GND sets 1-6 cells per V(CELLS) bins (0-0.9V=1, 4.5-5.5V=2, 0.9-1.8V=3, 1.8-2.7V=4, 2.7-3.6V=5, 3.6-4.5V=6). |+| 30 | OTG | input | Direction/mode select. Tie to GND for battery charging mode; drive above 1.2 V (e.g. to MODE) for battery discharging (OTG) mode. Hysteresis 200 mV. |+| 31 | TS | input | Battery temperature-sense input (NTC thermistor divider). Used for JEITA-style thermal qualification of charging. |+| 32 | VDD | power_in | 5.4 V internal LDO output that powers the PL5500 control core. Bypass to GND with a low-ESR capacitor. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | POWLICON |+| Package | QFN-32-EP(4x4) |+| Category | Power Supply Chip |+| Pins | 32 |++## Ordering variants++Same part, different packaging or reel option.++- `PL5500IQN32A`++## CAD (KiCad official)++- Symbol: `PL5500`+- Footprint: `Package_DFN_QFN:QFN-32-1EP_4x4mm_P0.4mm_EP2.9x2.9mm`+- 3D model: QFN-32-EP(4x4) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [POWLICON datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588917961151426560) (19 pp, sha256 `351bf4738852f535`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/pl5500-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "pl5500",+  "version": "0.1.0",+  "type": "component",+  "description": "POWLICON DC-DC Converters, QFN-32-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power supply chip",+    "pl5500"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "pl5500.kicad_sym",+    "pl5500.kicad_mod",+    "pl5500.glb",+    "pl5500.step",+    "pl5500.lbr",+    "docs/hero.png",+    "docs/pl5500-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file